Eric,
did you consider the Terratec Phase 26 USB already? I try to find out if the
input configuration will need our demands - - - without just buying one ...
73 - Klaus, DK7XL
"Eric" <[EMAIL PROTECTED]> schrieb:
> We have not yet found a suitable replacement for the MP3+ and the Extigy
> mainl
Frank,
I recall from my early RTTY days that switching between two tone generators
produces "non coherent" RTTY while shifting the tone of a single generator
gives "coherent" RTTY. Coherent vs non-coherent has to do with the
continuity of the AC waveform of the tone, where coherent is a conti
Folks
Although I guess I could figure it out, but does anyone have
the setup connections and perhaps beginning parameters for using the Berringer
802 with the SDR-1000. Would help if some of these diagrams were in addendums
to the manual.
Thanks
Eric
Eric, What specifically do you need to know? The actual
settings depend on the microphone you are using.
Use the first column of controls. Disregard all other controls except as
noted below.
Set all controls to the detent [default] position, or 12 o'clock
position.
Connect microphone ca
John,
If the calibration went well, the rig is working properly. Check the PWR
control on the console to make sure it is set to 100.
Gerald
> -Original Message-
> From: [EMAIL PROTECTED]
> [mailto:[EMAIL PROTECTED] Behalf Of John M. Belstner
> Sent: Wednesday, August 03, 2005 9:42 PM
> To
You will want to slew it slower than that. The bandwidth for (say)
45.45 baud with
170 Hz shift with a 4 ms slew rate would be almost 500 Hz. I think
10ms is more
like it as the minimum rate would be slewing over 20 ms.
Bob
Frank Brickle wrote:
I'm working on transforming the keyer into
I need a list of programs and HOW they key the radio. Some key the
radio through the same port they send CW. We have been using CW to key
the radio not keying and then sending CW. All of these settings (for
CW Type, etc.) can be configureable and it would be best if you send to
eric at flex
Are there written instructions for getting writelog to work?
SDR Setting
Kenwood TS50
Others?
WriteLog Setting
Which serial port for communication to Rig
Can also key..
Computer:
Load virtual serial port.
Change ini
To what ?
-
If I loaded the virtual seria
Mark,
I have never been able to test WriteLog with the current serial port/CAT
setup. I've had a little correspondence with the WriteLog folks but so far,
no real info on how to make it work with the SDR-1000. I just sent them
another query (and a copy of the latest CAT command dictionary) after
Thanks
For now -
I am running two computers for CW.
WriteLog on laptop to key output goes to SDR key input.
Mark Tyler
-Original Message-
From: Bob Tracy [mailto:[EMAIL PROTECTED]
Sent: Thursday, August 04, 2005 12:23 PM
To: Mark Tyler; [EMAIL PROTECTED]
Subject: RE: [Flexradio]
Good news. Phil C has confirmed that we may open all serial "things"
for 5 bit data with all of the usual stop bits so baudot will be
immediate after I install the controls, Frank gets done with the phase
continuous slewing modulator. The phase continuity really is imperative
for bandwidth c
I cannot use the Flex Radio/Ahti/Sami tool for an application I have
(Linux running SDR AMSAT transponder prototype) so who is using a USB to
DB25 adapter NOT from Flex and what is the model #?
Thanks in advance,
Bob
John
Thanks very much that should do me to get
connected up and running. I know that you had published before but I couldn’t
find it. I have several mics that I will try, however, I think in light of the Belize contest
I will end up with the Heil boomset. Which element should I get if I
Not sure how Ham Radio Deluxe does it, but you just enter the offset for
whatever frequency you dial to (after setting up the offset bands) and then
whenever you "tune to that frequency, it applies that offset. So you can
use one of the various signal sources to find the error for that band, a
John
Also if you are assuming that the Tune is the power out you will get on CW
it is incorrect. Confused me at first but in setup, you set the output level
for the Tun control on the front panel.
Eric - AA4SW
-Original Message-
From: [EMAIL PROTECTED]
[mailto:[EMAIL PROTECTED] On Behalf
It's taking a while but all the things are coming together. With a 100
Watt PA & & ATU coming in, I thought I would connect my Iambic paddle
via RS232 on COM 1.
I have been having some monitor delay problems before. Somewhat
corrected with the Delta 44 board set to 512.
Now I know that Eric, N4
Sid
Check the PTT setting in Setup. It cannot be disabled. Check that and you
should be good to go on any of the sources.
Eric - AA4SW
-Original Message-
From: [EMAIL PROTECTED]
[mailto:[EMAIL PROTECTED] On Behalf Of Sid Leben
Sent: Thursday, August 04, 2005 7:04 PM
To: FlexRadio
Subje
Eric and Bob - In answer to your request, my favorite program for keying CW
is MixW. MixW toggles my COM 1 serial port via the DTR line. That DTR line
toggles my external (Heathkit) keyer which toggles my SDR via the CW port on
the back panel of the SDR.
John Denson, AI6A
- Original Mes
Favorite programs are DX4Win for logging, psk, and cw. Keys through
serial or parallel port. Digipan for psk, MMTTY for rtty and
Hellscreiber by IZ8BLY which use the N8VB virtual serial ports.
73,
Dale AA5XE
Robert W McGwier wrote:
I need a list of programs and HOW they key the radio. Some k
Here I use MRP 40 from http://www.polar-electric.com/Morse/MRP40-EN/ -- he
uses DTR for PTT and RTS for keying, that configuration can be
reversed.My hope is to be able to use this via an N8VB vComm port so I
need to be able to tell PowerSDR to look at DSR for PTT and CTS for
keying. I
Hello all, I was considering using a DB 15
connector, appropriate plugs and shielded cable to interface between the SDR and
the Delta 44, bypassing the breakout box altogether. I thought this would
make a little cleaner setup here (not that this has mattered much before,
hi). I traced out
Bob
Several of us plan to use N1MM logger with SDR-1000 during the cqww phone
contest in October from Belize as well as doing some operation b4 and after.
According to the documentation with n1mm
Pin 7 RTS - PTT
Pin 4 CW - DTR
Pin 5 Common - GND
Can use com 1 - 8
Eric
-Original Message
Don
Yea!!! Thanks for the information! I have
Tony – KB9YIG awaiting a word to go ahead with 15 pin connector board
kits to interface directly to the Delta 44 with 1/8 inch stereo cables or
jacks. without external box etc. I have a mass of wires running all over the
place with infernal
CW-TYPE (www.dxsoft.com) uses DTR for PTT and RTS for Keying.
Mel, K0PFX
- Original Message -
From: "Bill Tracey" <[EMAIL PROTECTED]>
To: "Robert W McGwier" <[EMAIL PROTECTED]>; "Flexradio Reflector"
Sent: Thursday, August 04, 2005 10:22 PM
Subject: Re: [Flexradio] Serial keying, vi
Don
There are some real high dollar sound cards that are really and truly balanced,
but they cost as much as the SDR-1K. We use them extensively at work since all
our spots (commercials) all the drops (cute sound effects the jocks and talk
hosts play) and most of the music we play are on hard d
Eric
I have a drawing of exactly what you are asking for. Its in PDF form and I'll
be glad to send it to you. I can also send it in Visio (.vsd) or Autocad (.dwg)
format if you desire. At least one other list member is using my breakout box /
ground loop eliminator, and is happy with the result
Hi Bill, thanks for the info. I'm sorry I
missed your post, back on the 1st of July. Its amazing how much more money
it takes to set up an op-amp for diff. input vs single (Hi-end vs ours) input,
just a couple more resisters! Yes, I agree its a great card for SDR
use. Perhaps the reason
At 08:43 PM 8/4/2005, ecellison wrote:
Don
Yea!!! Thanks for the information! I have Tony KB9YIG awaiting a word
to go ahead with 15 pin connector board kits to interface directly to the
Delta 44 with 1/8 inch stereo cables or jacks. without external box etc.
I have a mass of wires running al
Thanks for all your replies.
The PWR control on the main console is set to 100. The Tune setting only puts
out 1W which is all that is necessary for an automatic antenna tuner.
I did notice that the CW keydown power jumped to 25W when I unplugged the
speakers (I'm using amplified PC speakers),
29 matches
Mail list logo
