[Flexradio] frequency

Hi I always find that I like the sound of a station on SSB when I tune 100 Hz off .. ie: 50.109900 instead of 50.110. Is there an easy way to put this 100Hz offset into the powerSDR setup? 73 Kevin ___ FlexRadio Systems Mailing List FlexRadio@fl

[Flexradio] Wanted internal Factory Tuner for 5000A

Hi; Recently purchased a 5000A ,I'm looking for a used factory internal tuner. 73 Dan K8ICB in Florida ___ FlexRadio Systems Mailing List FlexRadio@flex-radio.biz http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz Archives: http://www.

[Flexradio] 5K PA and Driver bias readings

I have the preliminary 2007-2008 service manual for the 5K and am running the BITE tests. It states that the bias currents for the driver and PA should be 200 ma and 1.4A, respectively. The actual values I'm getting are considerably higher than that: 1.0A and 2.264A(nominal). These values ar

[Flexradio] v.2.0.22 startup problems

Am having trouble starting up v.2.0.22 on my 5K. There are three scenarios: 1) I double-click on the PSDR icon and nothing happens. When I double-click again, I get error message that other PSDR instances are running. The only way to recover is to restart my computer. 2) After double-clickin

Re: [Flexradio] v.2.0.22 startup problems

On Thu, Jul 14, 2011 at 4:56 PM, Rod Brink wrote: > ... error message that other PSDR instances are running. The only way to > recover is to restart my computer > > = Rod, you can usually recover from this without restarting. Right-click on the Taskbar and click Start Task Manager. A

Re: [Flexradio] 5K PA and Driver bias readings

The service manual has not been updated in this regard. The PA BIAS driver target is 1.0 amps and the PA BIAS Final target is 2.28 amps. These values were change a while back to improve the audio quality of phone modes. Your numbers are dead on target. The values you see in the debug form a

Re: [Flexradio] v.2.0.22 startup problems

Was it ever working with 2.0.22 or is this behavior new? -Tim --- Tim Ellison, W4TME Internet Systems Admin. & Customer Support Engineer FlexRadio Systems^(TM) 4616 W Howard Ln Ste 1-150 Austin, TX 78728 Phone: 512-535-4713 Ext. 223 Email: t...@flexradio.com Web: www.f

Re: [Flexradio] v.2.0.22 startup problems

Rod, Are earlier versions running ok? Reason I ask, you are below the minimum CPU to run PowerSDR, not that it can't work, but it is going to be pretty marginal . If previous versions were 2.x versions, try holding the left shift key, while double clicking PowerSDR, this should bri

Re: [Flexradio] v.2.0.22 startup problems

Tim - The 5K is new to me (second-hand) and v.2.0.22 is my first experience with PSDR. Lee K9WRU has had the same problem and has theorized that it might be a symptom of an "over-the-hill" computer. At his suggestion I am now slow-clicking the PSDR icon to prevent ghost versions from starting

Re: [Flexradio] frequency

Kevin, Make sure that you have followed the frequency calibration for your radio.. then check your radio.. If you must, you can offset the DDS , but that will effect the other frequencies severely. 73, Dudley WA5QPZ On 7/14/2011 10:03 AM, Kevin Hobbs wrote: Hi I always find that I

[Flexradio] Bal line out Mic W2IHY

Hey there guys - I read on the site about connecting my 8-band EQ to my new 5K. W2IHY EQ Plus to balanced audio in cable wiring: DIN pin 1 to 1/4" TRS tip DIN pin 2 to 1/4" TRS ring DIN pin 5 to 1/4" TRS shell What is a TRS plug ? I thought the bal line jack on the back was RCA not what this s

Re: [Flexradio] frequency

Use RIT to give you a 100 Hz offset. -Tim --- Tim Ellison, W4TME Internet Systems Admin. & Customer Support Engineer FlexRadio Systems^(TM) 4616 W Howard Ln Ste 1-150 Austin, TX 78728 Phone: 512-535-4713 Ext. 223 Email: t...@flexradio.com Web: www.flexradio.com

Re: [Flexradio] Bal line out Mic W2IHY

TRS = Tip Ring Sleeve http://en.wikipedia.org/wiki/TRS_connector Tim Ellison, W4TME Internet Systems Admin. & Customer Support Engineer FlexRadio Systems^(TM) 4616 W Howard Ln Ste 1-150 Austin, TX 78728 Phone: 512-535-4713 Ext. 223 Email: t...@flexradio.com Web: www.f

Re: [Flexradio] frequency

Just how does one check the frequency calibration on a F5k? TIA, ~~Guy W6NJX On 7/14/2011 5:45 PM, Dudley Hurry wrote: Kevin, Make sure that you have followed the frequency calibration for your radio.. then check your radio.. If you must, you can offset the DDS , but that will effect

[Flexradio] Bal line out Mic W2IHY

So just as I thought a 1/4" stereo plug... Roger that... Thanks From: Tim Ellison, W4TME Sent: Thursday, July 14, 2011 8:18 PM To: flexradio@flex-radio.biz Subject: Re: [Flexradio] Bal line out Mic W2IHY TRS = Tip Ring Sleeve http://en.wikipedia.org/wiki/TRS_connector On 7/14/2011 9:05 PM

Re: [Flexradio] frequency

On Thu, Jul 14, 2011 at 6:30 PM, Guy Harris wrote: > Just how does one check the frequency calibration on a F5k? > 1. tune in WWV or CHU 2. Setup>general>calibration 3. Select WWV frequency 4. press START 5. go look at the clock offset in setup>general>hardware config>DDS-Expe

Re: [Flexradio] frequency

Or just tim the frequency calibration routine in the Setup form using a WWV Frequency. -Tim Sent from my iPhone On Jul 14, 2011, at 10:13 PM, Brian Lloyd wrote: > On Thu, Jul 14, 2011 at 6:30 PM, Guy Harris wrote: > >> Just how does one check the frequency calibration on a F5k? >

Re: [Flexradio] frequency

On Thu, Jul 14, 2011 at 7:28 PM, Tim Ellison, W4TME wrote: > Or just tim the frequency calibration routine in the Setup form using a WWV > Frequency. > I think he is trying to determine if there is a problem. If PowerSDR is able to self-calibrate the radio to WWV with some kind of reasonable cl

Re: [Flexradio] frequency

Guy, It's really easy with WWV (or you can use any other high calibrated signal) , go to the Calibration tab of Setup, page 132 of the current Owners Guide, click the Expert box, with a good signal on WWV, at least a S5 on the meter, be sure to match the frequency box to the WWV or gen

Re: [Flexradio] frequency

On 15-07-2011 04:13, Brian Lloyd wrote: On Thu, Jul 14, 2011 at 6:30 PM, Guy Harris wrote: Just how does one check the frequency calibration on a F5k? 1. tune in WWV or CHU And with the radio in which mode ? 2. Setup>general>calibration 3. Select WWV frequency 4. press STA