[Flexradio] COM port keying -

Disconnect everything from com1. Measure the voltage POLARITY at each pin number. (Com1) As soon as one hooks up the Ground lead to any pin (4,6, or 8 I think) this will key the rig. One needs an interface that isolates the ground. Use an optoisolator . Mark Tyler K5GQ

[Flexradio] K2 has ONLY 80dB of third order dynamic range vs SDR-1000 98dB

From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] Sent: Saturday, September 10, 2005 11:20 AM To: Mark Tyler; [EMAIL PROTECTED] Subject: K2 has ONLY 80dB of third order dynamic range vs SDR-1000 98dB In a message dated 9/10/2005 11:25:53 A.M. Eastern

[Flexradio] CW - missing dits. with external keyboard on COM1

K5GQ From: Eric Wachsmann - FlexRadio [mailto:[EMAIL PROTECTED] Sent: Friday, September 09, 2005 3:14 PM To: Mark Tyler Subject: RE: CW - missing dits. What are your buffer sizes set to? (Audio, DSP, D44 DMA) I would suggest trying 512, 512, 512 and see if that improves th

[Flexradio] CW - Paddle Src - Com1

On the Keyer tab of the DSP tab under Setup. The COM1 is selected as the "Paddle Src", 4 -Comm, 6-Dit, 8-Dash Have not: checked Device Manager Expand the Ports tree. see (COM1 through COM#) ? other thoughts Mark Tyler K5gq

[Flexradio] serial com port keyer - Common pin 4, dit pin 6 and dash pin 8 in a DB9

I am trying to operate CW -- 25 to 35 wpm -- If one plugs into the key input of the radio and uses an external computer to key rig, Software set for Parallel the result is the output drops dits; just as it sounds on the monitor. Not able to key with serial port of computer. It is the SDR a

[Flexradio] Thanks - RE: WriteLog -

Thanks For now - I am running two computers for CW. WriteLog on laptop to key output goes to SDR key input. Mark Tyler -Original Message- From: Bob Tracy [mailto:[EMAIL PROTECTED] Sent: Thursday, August 04, 2005 12:23 PM To: Mark Tyler; [EMAIL PROTECTED] Subject: RE: [Flexradio

[Flexradio] WriteLog -

Are there written instructions for getting writelog to work? SDR Setting Kenwood TS50 Others? WriteLog Setting Which serial port for communication to Rig Can also key.. Computer: Load virtual serial port. Change ini To what ? - If I loaded the virtual seria

[Flexradio] CW with ver 1.4.4

Tried to work the QRP CW Spartian Sprint last night. -- Upgraded to 1.4.4 15 minutes before contest. when one tunes in a cw station, one gets noise from audio output on one side and cw on other; before both sides. -- sidetone volume when preamp is changed sidetone level is the same. I be

[Flexradio] New Install - USB- Parallel PROBLEMS -

ERAL tab selected USB to parallel. Port address did not appear to be critical. Radio is in stand by mode. Receives as soon mode changed to operate. K5GQ Mark Tyler Houston, TX 77043 Fax 713 461 1435

[Flexradio] source radio control subsystem -- 'hamlib' (www.hamlib.org).

>From WriteLog Reflector - Re: [WriteLog] CAT Support from [Darren Hatcher] [Permanent Link][Original] To: <[EMAIL PROTECTED]> Subject: Re: [WriteLog] CAT Support From: "Darren Hatcher" <[EMAIL PROTECTED]> Reply-to: [EMAIL PROTECTED] Date: Thu, 23 Jun 2005 20:40:58 +0100 List-post:

[Flexradio] Anyone using WriteLog with SDR-1000

I am currently using WriteLog with FT900 in the mobile. (While someone else drives.) The Heil headset mic goes into the mic input of the computer. (Computer sound card supplies voltage for the electrect condenser microphone.) The computer speaker output goes to the digital input in the rear of t