Thanks for your input Chris.
Now I have also installed the latest SVN and also the New K6JCA console
program.
You are right. I can confirm that this long delay on the transmitted audio,
after using TUNE, in digimodes has gone completely in both these versions.
Many thanks to all the hard worki
isten to a second receiver, or watch the current of the power supply.
>
> Eddy ON5UQ.
>
> - Original Message -
> From: "Tim Ellison" <[EMAIL PROTECTED]>
> To: "Van de Velde Eddy" <[EMAIL PROTECTED]>; "NU8Z"
> <[EMAIL PROTECTE
rrent of the power supply.
Eddy ON5UQ.
- Original Message -
From: "Tim Ellison" <[EMAIL PROTECTED]>
To: "Van de Velde Eddy" <[EMAIL PROTECTED]>; "NU8Z"
<[EMAIL PROTECTED]>;
Sent: Sunday, January 20, 2008 2:50 PM
Subject: RE: [Flexradio]
Gentlemen,
Indeed, this problem was on the reflector before. But, as far as I know, it
got no attention. I tried to get help on the HRD forums but no luck either.
As it was said before, this long delay comes up after using the Tune button
in PowerSDR. It can be fixed by clicking VAC off and on
Using SDR-1000 and PowerSDR v1.10.3 and Delta-44 sound card.
When I leave the USA band plan in PowerSDR.mdb file. No problems with the PA
calibration routine.
However, when I have imported Region1BandText.mdb into PowerSDR.mdb file with
PowerSDR Data Import Utility, there is no RF output on 60
I installed PowerSDR v1.10.0 and have successfully imported the
Region1BandBandTextTable into the PowerSDR.mbd file, using Ray K9DUR's new
Database Table Migration Utility v2.2.0.
Thank you very much Ray for your updated software ! And thank you Ahti OH2RZ
and Bodo DJ9CS for providing us with t
Hello Howard,
I have sent the same question to the list. I found I can calibrate the
frequency with the 50 microvolt of the Elecraft XG-2. After calibration to
that signal, I can even as well calibrate on the 1 microvolt signal of the
XG-2. It appears as if the frequency of the SDR is too far o
I seem to have a problem to calibrate the frequency in PowerSDR v1.9.1. Peak is
always out of valid range. Never had this problem with PowerSDR v1.8.0. Using
RWM here to do the calibration wich signal is always S9+. If I do the
calibration in v.1.8.0 and quit and open Beta 1.9.1, then the freque
What is the best way to connect a Kenwood MC-50 microphone ? That is a dynamic
moving coil type, unidirectional 600 Ohm at 1000 Hz.
I have the Delta-44 sound card with break-out box and have INS 3 and 4 from the
break-out box connected to MIC IN of the SDR-1000. There are Pin 7 Mic(-) and
Pin
Ray,
I have installed Data Import utlility version 2.1. Importing
Region1BandText.mdb works perfect now. Thank you very much for your help and
work.
I also want to thank Klaus DK7XL, K6JCA and W4TME for their help to try and
find the cause of this European problem.
73 Eddy ON5UQ.
Ray,
The read only box was not checked in the mbd files.
I downloaded MDAC 2.8 from Windows and tried to install it. This results in
an error "This version is incompatibel with Windows XP SP2. All facilities
of this software are curently used by this version of Windows.
Uninstall and install P
llison" <[EMAIL PROTECTED]>
To: "Van de Velde Eddy" <[EMAIL PROTECTED]>;
Sent: Saturday, January 20, 2007 7:36 PM
Subject: RE: [Flexradio] Error importing Region1bandText.mbd
> Are you using version 2.0 of the SDRDataImport program?
>
> Where in the sequence of
Anyone who can help ?
I tried to import the Region1Bandtext.mbd file using SDRDataImport.exe
following the instructions from the articles of the KB.
This gives the following error :
PowerSDR Data Import Utility
Run-time error '424'
Object required.
Eddy ON5UQ.
-- next part -
The address of the second par. port on my computer is DFF0. This is not in the
pull-down menu of PowerSDR Beta v1.6.3. The computer is a Pentium IV, Windows
XP SP2.
Is there a way to drive my SDR-1000 from this port ? The other port's address
is 0378. So it is odd that the second one is not as
Anyone using an external 10 MHz reference clock for the SDR-1000 ? I bought the
SDR-ERK clock kit. But I could not find any documentation for the modification
on the Knowledge Base.
73 Eddy ON5UQ.
-- next part --
An HTML attachment was scrubbed...
URL:
/pipermail/flexrad
The maximum output of the Elacraft XG-2 is -73 dBm. The manual of the SDR-1000
requests a signal of -50 dBm for the Automatic calibration of the Image Null.
Is the -73 dBm of the XG-2 insufficient for a reliable I mage Null Calibration ?
73 Eddy ON5UQ.
-- next part --
An
Brian,
Problem fixed. I deleted all files of SVN : 670 and downloaded it again.
Calibration is now working perfect. Something must have gone wrong on first
download and install.
I'm a new SDR-1000 user since a month now. I want to thank all people
involved in hard- and software of this great
"Tim Ellison" <[EMAIL PROTECTED]>
Cc: "Van de Velde Eddy" <[EMAIL PROTECTED]>;
Sent: Saturday, September 09, 2006 7:18 PM
Subject: Re: SVN : 668 and SVN : 670
> Just tried it here with 670 and XG-1 and have no problems. What
> signal source and dBm
I seem to have a problem with the RX Level Calibration when using PowerSDR
v.1.6.3 SVN : 668 and also with SVN : 670.
The " calibrating RX level" window opens but no counting at all.
No such problem with Power SDR v.1.6.2.
73 Eddy ON5UQ.
-- next part --
An HTML attachmen
Re : VAC and digimodes.
Thanks very much for all the help in this matter. I unistalled VAC 4.03 and
installed V 3.12 and Ham Radio Deluxe.
CAT control and VAC are now working fine. I have just made my first qso in
psk31 with my new SDR-1000 100 Watts.
73 Eddy ON5UQ.
-- next part -
Anyone using VAC 4.03 with digimodes software ?
I want to use VAC to run my SDR-1000 with software for digital modes like
PSK31 Deluxe and Hamscope. I have looked through all related documents that
I could find. But I cannot fix the problem.
On receive, all works fine and the Control panel show
Hello,
I'm a new SDR-1000 100 watts owner and getting started with this fascinating
hard- and software. Is there anyone using Hamscope and VAC ?
73, Eddy ON5UQ.
-- next part --
An HTML attachment was scrubbed...
URL:
/pipermail/flexradio_flex-radio.biz/attachments/200608
22 matches
Mail list logo
