I have a new box and have been trying to install 7.2 amd64 on it for the
past week. I now see that 8.0-BETA1 is available and would be willing
to install it if it supports my intended config below.
I'm using this page as a guide but am at the console so I'm just using
the Fix It CD:
http://www.f
On 7/14/2005 7:57 AM Pertti Kosunen wrote:
Drew Tomlinson wrote:
So where in the boot sequence is GEOM_STRIPE loaded? I'm starting to
suspect it's being loaded twice. I have it in /boot/loader.conf
which is where I thought it should be. Is there anywhere else to check?
I
On 7/14/2005 5:30 AM Giovanni P. Tirloni wrote:
Drew Tomlinson wrote:
GEOM_STRIPE: Device data created (id=896603271).
GEOM_STRIPE: Disk da0d attached to data.
GEOM_STRIPE: Disk da1d attached to data.
GEOM_STRIPE: Device data activated.
GEOM_STRIPE: Cannot add disk da0s1d to data (error=17
I posted the following on -questions but have not received any
assistance. I also have since tried compiling GEOM_STRIPE support in
the kernel but get the same behavior (except that I can't perform the
kldunload/load workaround). I'm hoping someone here may be able to
point me in the right di
On 3/30/2005 9:30 PM Karl Denninger wrote:
On Wed, Mar 30, 2005 at 10:44:38AM -0800, Drew Tomlinson wrote:
I missed the beginning of this thread and apologize if my question has
already been covered. But can you tell me if this issue might be the
reason my PC locks up intermittently ? I
On 3/30/2005 9:39 AM Karl Denninger wrote:
On Wed, Mar 30, 2005 at 12:07:22PM -0500, Jim Trigg wrote:
On Wed, March 30, 2005 12:43 am, Karl Denninger said:
Here's the diff and some thoughts
[snip, including first diff]
241,243c244,249
<
< /* if reinit succeeded and ret
Since an upgrade from 4.9 to 4.10, I've had problems with vinum. The basic
problem is that upon reboot, two of my vinum drives show up as
"referenced" and
thus create the associated chaos. I've tried many things and fiddled
around
quite a bit so I can't say exactly what I've done. I can includ
I've been happily using 4.9-RELEASE-p4 since April 2004. Last weekend,
I decided to upgrade to 4.10-RELEASE-p3 to fix the pthreads problem
since I had just added an external tape drive to the QLogic SCSI card
that was already in my system.
Anyway, after upgrading, I experienced the same shutdo
On 11/3/2004 7:15 PM Doug White wrote:
On Wed, 3 Nov 2004, Drew Tomlinson wrote:
Can someone please tell me what the aic_recovery process is in my ps
-acux output? Maybe if I can read about this, I can figure out where my
whole problem lies. My original post is below.
They're k
On 11/3/2004 4:16 PM Vivek Khera wrote:
On Nov 3, 2004, at 7:04 PM, Drew Tomlinson wrote:
So, does shutdown complete on your system? I don't know if you read
this thread or not but I'm experiencing the same symptoms.
http://lists.freebsd.org/pipermail/freebsd-current/2003-Decembe
On 11/3/2004 12:52 PM Vivek Khera wrote:
On Nov 3, 2004, at 1:15 PM, Drew Tomlinson wrote:
Can someone please tell me what the aic_recovery process is in my ps
-acux output? Maybe if I can read about this, I can figure out where
my whole problem lies. My original post is below.
I'm not
Can someone please tell me what the aic_recovery process is in my ps
-acux output? Maybe if I can read about this, I can figure out where my
whole problem lies. My original post is below.
Thanks,
Drew
On 11/1/2004 9:04 AM Drew Tomlinson wrote:
I've been happily using 4.9-RELEASE-p4
I've been happily using 4.9-RELEASE-p4 since April 2004. Over the
weekend, I decided to upgrade to 4.10-RELEASE-p3 to fix the pthreads
problem since I had just added an external tape drive to the QLogic SCSI
card that was already in my system.
Anyway, after upgrading, I experienced the same sy
- Original Message -
From: "Jamie Bowden" <[EMAIL PROTECTED]>
To: "Drew Tomlinson" <[EMAIL PROTECTED]>
Cc: <[EMAIL PROTECTED]>
Sent: Monday, November 04, 2002 1:30 PM
Subject: Re: Firewire.
> On Mon, 4 Nov 2002, Drew Tomlinson wrote:
>
>
I have an AMD 486 DX-100 machine that has run flawlessly since
4.0-RELEASE. Although slow, I build custom kernels, and use ports to
build and install software. The software on this machine is minimal
as I use it for my firewall and to serve DHCP requests. Here is the
list of installed ports:
b
15 matches
Mail list logo
