Em Qui, 2006-10-19 às 20:00 +0200, Carlos Nieves Ónega escreveu:
From your comment, I guess the refdes attribute position depends on
the
type of the symbol: if it's a resistor or a capacitor then you want it
at one place, but if it's an IC, then you put it at another place. Am
I
right?.
-BEGIN PGP SIGNED MESSAGE-
Hash: SHA1
Icarus Verilog has lacked a User Guide for too long now, so I've
started a documentation Wiki here: http://iverilog.wikia.com.
I've seeded it with some documentation that I've been hoarding
for a while now, and also got the basics of the layout more
One step left before I start taking orders. Almost there!
I've pretty much finished the web page and instructions for the
challenge board project, and would like to request a review.
Specifically, the link marked instruction sheet is the [double
sided] page I'm including with the mailed kits.
2nd paragraph. There's all sorts of things should probably be
There are all sorts of things.
Fixed.
from the time the parts get here should maybe from the time the
parts get there.
I meant *my house*. From the time the parts leave Digikey to the time
you finish assembling your board. I
On 10/20/06, Stephen Williams [EMAIL PROTECTED] wrote:
Icarus Verilog has lacked a User Guide for too long now, so I've
started a documentation Wiki here: http://iverilog.wikia.com.
I've seeded it with some documentation that I've been hoarding
for a while now, and also got the basics of the
John Coppens wrote:
On Fri, 20 Oct 2006 01:35:29 -0400
Dan McMahill [EMAIL PROTECTED] wrote:
% kpsewhich -progname=dvipdfm -format=tfm cmr17
/usr/pkg/share/texmf/fonts/tfm/public/cm/cmr17.tfm
man dvipdfm may give enough info to dig into it. I'm afraid I'm not
going to be able to help much
On Oct 20, 2006, at 7:47 PM, Dan McMahill wrote:
% kpsewhich -progname=dvipdfm -format=tfm cmr17
/usr/pkg/share/texmf/fonts/tfm/public/cm/cmr17.tfm
man dvipdfm may give enough info to dig into it. I'm afraid I'm
not going to be able to help much beyond this.
on6jc ~$ kpsewhich
DJ Delorie wrote:
I've built three so far (two proto, one final). I'm going to use one
or two more finals to try out my new hot plate before I start working
on the expansion board project (the SOJs almost require reflow). So,
I can't wait to get rid of them all ;-) (and I'm not going smaller
On 10/20/06, Dan McMahill [EMAIL PROTECTED] wrote:
John Coppens wrote:
On Fri, 20 Oct 2006 01:35:29 -0400
Dan McMahill [EMAIL PROTECTED] wrote:
% kpsewhich -progname=dvipdfm -format=tfm cmr17
/usr/pkg/share/texmf/fonts/tfm/public/cm/cmr17.tfm
man dvipdfm may give enough info to dig into it.
yeah, I've never liked soldering SOJ's. Although I'd rather do
those than QFN's.
I'd have preferred tsops, but I can do trace-between-pads with SOJ,
and I was kinda limited given the part I needed (5v SRAM).
I wonder if you can hand-solder SOJ if you start by putting solder
paste on the
On Fri, 20 Oct 2006 14:01:23 -0400
DJ Delorie [EMAIL PROTECTED] wrote:
One step left before I start taking orders. Almost there!
I've pretty much finished the web page and instructions for the
challenge board project, and would like to request a review.
Specifically, the link marked
In instructions.pdf, Quantities in the table don't match the board or the
resdef numbers.
C2-5 Qty 2 - should be 4
There are two oscillator configurations, so the schematic has two
places for caps for each oscillator. You only populate one each.
This is noted in the instructions. I added
I'll give some feed back to that. I was planing on ordering ten.
Not that I'm that bad at soldering, but some people at work could use
some practice.
Note that ten packs aren't cut up; you'll need a scroll saw or other
pcb cutter with a narrow kerf. I use a #2 blade. I'm going to cut up
the
Won't two AA's power this rather than messing with a 9V and 7805?
Hey! It works! And no injection locking either.
___
geda-user mailing list
geda-user@moria.seul.org
http://www.seul.org/cgi-bin/mailman/listinfo/geda-user
On Oct 20, 2006, at 10:26 PM, DJ Delorie wrote:
Won't two AA's power this rather than messing with a 9V and 7805?
Hey! It works! And no injection locking either.
Schweet!
-Dave
--
Dave McGuire
Cape Coral, FL
___
geda-user mailing
Hey! It works! And no injection locking either.
Schweet!
Yeah, that was definitely a pleasant surprise.
Not that I can explain it, of course.
But now I have to reconfigure my latest board to use the twin slow
oscillators, so I can see the LEDs throb. That means moving one of
the
On Fri, 20 Oct 2006 20:13:37 -0400
John Luciani [EMAIL PROTECTED] wrote:
Since the DVI file is generated can you view it with xdvi? If you can
I would think
that the problem may be with fontmapping.
Sri... Hadn't noticed that the make script seems to remove the output
(dvi)? As far as I can
17 matches
Mail list logo
