Fahad,
BFD probes directly connected IP neighbors (since it is run over IP) , in case
of L2circuit it will be CE-CE.
803.2ah is scheduled in future JUNOS releases, AFAIK.
I'm still not clear why you need to probe CE-PE link. If BFD/IP SLA probes
would indicate CE-CE connectivity problem on IP le
This can also be an extended LDP discovery issue. Can you possibly share
your ldp configuration for the problem juniper routers, a show ldp database
| match "Input|L2CKT" , and a show l2circuit connections.
That's the simple setup I have
6500-sup720
|
|
Please ignore
___
juniper-nsp mailing list juniper-nsp@puck.nether.net
https://puck.nether.net/mailman/listinfo/juniper-nsp
Alex.Clear me in one thingdoes BFD can probe L2circuit...and this
probing is done from CE to PE?
This is confusing. and if it can probe L2circuit.L2circuit will remain
UP...it didn't depend on the failure of Lastmile of client (when CE connects
to FR Switch/L2 Switch and NNI/Trunk to P
Hi,
Try this configuration:
---
[EMAIL PROTECTED]> show configuration chassis
fpc 0 {
pic 1 {
framing sdh;
}
}
---
[EMAIL PROTECTED]> show configuration interfaces so-0/1/1
hold-time up 50 down 50;
clocking external;
encapsulation cisco-hdlc;
sonet-options {
payload-sc
Hello, and welcome.
Yes, POS is supported on that card:
http://www.juniper.net/techpubs/software/junos/junos82/swconfig82-network-interfaces/html/interfaces-sonet-config31.html#1014875
As an FYI, I think you will want to enable 32 bit fcs, and explicitly disable
payload scrambling on the jni s
Hello ... I am new in this mailing list, i will apreciate so much your
help.
We need to connect a Juniper m10i with a Cisco Router 10008 ( with a STM1)
but the cisco router has a Cisco 6 Port OC3 POS card ( ESR-6OC3/P-SMI ) ,
We have a 4x STM-1 SDH, SMIR module in our Juniper M10 i.I was r
Are the routes also installed as IGP routes?
Due to ordered control, the L2circuit neighbor must be an IGP route.
Do you see labels advertised with show ldp database?
Doug
-Original Message-
From: [EMAIL PROTECTED]
[mailto:[EMAIL PROTECTED] On Behalf Of Christian Malo
Sent: Wednesday, J
That's the simple setup I have
6500-sup720
|
|
|
m5 m20--> bunch of other routers
I have ldp enabled on every router and the m20 has no problems setting up
l2circuits to every router except the m5 and 6500.
I noticed on th
Hi All
for an IQ PIC, when I configure a bandwidth command as follows (from JUNOS
docs), is the traffic shaped first or the traffic put into the scheduler first?
[edit interfaces]
t3-1/0/0:1 {
encapsulation frame-relay;
per-unit-scheduler;
}
[edit class-of-service]
interfaces {
t
Your understanding is correct but let me clear some background issues that i
discuss few days ago..!
Most of our client termination are in a manner that Ethernet clients are
terminated over switch and than truncked to Juniper..and FR clients are
terminated over NNI between FR switch and Junipe
Well Alex it will help in CE-CE link tracking.and PE will never know any
thing.!
But consider a scenario, On PE-A clinet hav two last miles, one primary and
other backup. We configure L2Circuit and set Pri lastmile as primary link
and secondary lastmile as protected one (under the protocol
Hi All,
Has anyone configured load-balancing on the LDP over RSVP tunneling based? Is
M10i chassis support that feature?
Thanks,
Benny
-
Everyone is raving about the all-new Yahoo! Mail beta.
___
juniper-nsp mailing l
Fahad,
If you are looking for End-to-End failure detection for L2VPN where PE-CE links
are Ethernet then You can do it either with BFD or IP SLA Cisco feature. Please
be aware than BFD/IP SLA do not actually bring down the interface/subinterface,
they either tear down IGP adjacencies (BFD), remo
Fahad,
If your Ethernet switch do not support any keep-a-live mechanism (e.g.
eth OAM 802.3ah) there is no way to detect that VLAN is down, when whole
port is up. So, I do not see possiblility to detect problem with CE -PE
logical link. There is just nmo such information available. And, BTW,
t
Thanx Alex!
FREEK worksbut there comes another issue like thatas we transport
VLAN-TCC and VLAN-CCC clients. If there lastmile goes down.VLAN BPDUs
will still recieve over Turnk port (Switch to Juniper). So it coz L2Circuit
to remain up.
I look for the Ethernet/VLAN OAM that defin
16 matches
Mail list logo