[j-nsp] JUNOS OID

Hello ALL Please teach OID concerning the memory utilization of JUNOS. Model:M10i Version:9.6R3.8 ___ juniper-nsp mailing list juniper-nsp@puck.nether.net https://puck.nether.net/mailman/listinfo/juniper-nsp

Re: [j-nsp] IKE gateway within routing-instance

On Tue, Aug 10, 2010 at 01:56:01PM +1000, Ben Dale wrote: Yes - I've been told this is due in 10.4 Not sure of your application, but you can still place your st0 interface inside a routing-instance, but the outgoing-interface specified in the IPSEC GW configuration must be present in

[j-nsp] FPC shell command to disable the interface Tx laser

I have a lab environment and I want to simulate a fiber cut, but I'm not able to physically pull the fibers. I know that if the CLI is used to disable an interface, the code has mechanisms that assist protocol convergence. I saw a JTAC engineer enter a command from the FPC shell that cuts the

[j-nsp] set cli screen-width

Experts, This operational mode command is lost normally at logout and threfore I have to type it again when I relogin. Is there a way to make permanent? Tx. ___ juniper-nsp mailing list juniper-nsp@puck.nether.net

[j-nsp] MS-DPC export flows have 0 as dest interface

All, It has been a bit of a battle for me as a first time Juniper user to get Netflows exported using an MS-DPC. With a tremendous amount (some from this list) of help the flows are being exported. However, The Juniper is not reporting the dest interface and instead putting in a zero. This

Re: [j-nsp] FPC shell command to disable the interface Tx laser

I got the answer offline. On an MX or T-Series router for a 10GE interface, use the following commands: start shell pfe network fpcX test xfp index laser off You can find the XFP index by doing show xfp list from the shell prompt. I haven't seen a method that works for SFP interfaces.

Re: [j-nsp] MS-DPC export flows have 0 as dest interface

On Tue, Aug 10, 2010 at 01:01:48PM -0700, Jim Devane wrote: However, The Juniper is not reporting the dest interface and instead putting in a zero. This is confusing our flow collector (Peakflow SP) Arbor takes the dest intf and source interface both being zero as a drop. The traffic is

Re: [j-nsp] MS-DPC export flows have 0 as dest interface

RAS, 10.0R2 I opened a case and we will see what happens. I have zero issue with moving to new code if it will solve the issue. This router doesn't do a whole lot (and even less without correct flow reporting) Thanks, Jim -Original Message- From: Richard A Steenbergen

[j-nsp] Egress Policing / Layer2

Hi there. I haven't had time to lab this up due to travelling but we are trying to find a way to do egress policing on an EX switch for VLAN's - is there a such thing? I understand there is ingress policing? These are EX4200 switches primarily where a LAN service comes in one port and

[j-nsp] Hi latency in GE interface

Hello , I have a juniper m10i with a GE interface . Running junos 8.2 . The router is connected to an External Router via one GE interface. But the GE interface is reporting hi latency . In a normal working the delay between the two routers is 5 ms. (the m10i router and other external

Re: [j-nsp] Default SRX Behaviour

I just wanted to respond back on-list about this .. thank you to everyone who made suggestions on this issue. The set security flow tcp-session no-syn-check resolved our issue as suggested below. My last question is to understand the risk associated to disabling the syn-check. Does this effect