Isidoro,
the SSD must be jumpered to SLAVE.
The onboard CF is already master and thus you get this error message
(PAGE FAULT).
The other error message you have when you set it to SLAVE is probably
because you have no active partition on the SSD (did you re-install
junos on the SSD?).
Please jum
Hi all,
We have disk errors again. We bought a SSD ( TS8GSSD25-S ) to replace
the HDD with problems. If we connect the SSD the router does not boot,
the following error appears:
/_- SSD as CS or Slave:_
Will try to boot from :
PCMCIA ATA Flash Card...
Dear Isidoro,
glad it worked for you that way.
Please keep in mind that the Fujitsu MHT2030AT are long time end-of-life
and the disk you purchased was likely used already. Also the -AT Fujitsu
drives are not rated for 24x7 operation thus are a potential problem.
Only the -AS series are classified
Dear Jonas,
Two weeks ago we replaced the HDD(
http://juniper.cluepon.net/Replacing_the_harddisk_with_solid_state_flash
).
We bought a identical HDD ( P/N MHT2030AT)and copy the data 1:1 (
using the windows software "EASEUS Todo Backup Free 3.0" ),
The cloning process took 35 mi
e-
From: juniper-nsp-boun...@puck.nether.net
[mailto:juniper-nsp-boun...@puck.nether.net] On Behalf Of Jonas Frey (Probe
Networks)
Sent: Thursday, 22 September 2011 12:52
To: Isidoro Cristobal
Cc: juniper-nsp@puck.nether.net
Subject: Re: [j-nsp] HDD Write Error
Dear Isidoro,
you ca
gt; > > Failed attribute: (200)Write Error Rate
> > > /
> > >
> > > Could this be related?.
> > >
> > > Best Regards
> > >
> > > Isidoro
> > >
> > >
> > >
> > > El 22/09/2011 8:05
.net
Subject: Re: [j-nsp] HDD Write Error
Dear Isidoro,
you cant copy the data 1:1atleast not without alot of work.
The best thing would be if you reinstall JunOS via a install media (pcmcia/cf
card) once you replaced the hard disk.
Its very easy to replace the hard disk on either RE2/3/4/5
22/09/2011 8:05, Josh Farrelly escribió:
> > Could you put them both in a Linux box and just 'dd if' them?
> >
> > -Original Message-
> > From: juniper-nsp-boun...@puck.nether.net
> > [mailto:juniper-nsp-boun...@puck.nether.net] On Behalf Of Jon
Of Jonas Frey (Probe
Networks)
Sent: Thursday, 22 September 2011 12:52
To: Isidoro Cristobal
Cc: juniper-nsp@puck.nether.net
Subject: Re: [j-nsp] HDD Write Error
Dear Isidoro,
you cant copy the data 1:1atleast not without alot of work.
The best thing would be if you reinstall JunOS via a install me
uniper-nsp@puck.nether.net
Subject: Re: [j-nsp] HDD Write Error
Dear Isidoro,
you cant copy the data 1:1atleast not without alot of work.
The best thing would be if you reinstall JunOS via a install media (pcmcia/cf
card) once you replaced the hard disk.
Its very easy to replace the hard disk
Dear Isidoro,
you cant copy the data 1:1atleast not without alot of work.
The best thing would be if you reinstall JunOS via a install media
(pcmcia/cf card) once you replaced the hard disk.
Its very easy to replace the hard disk on either RE2/3/4/5...its
normally only secured by 4 screens on
Hi,
you are correct, the disk exceeded the maximum write errors permitted by
the SMART value and thus is marked as bad. Prepare for a complete
failure of the drive soon (1-30 days likely).
May be the right time to upgrade the harddisk to a SSD.
http://juniper.cluepon.net/Replacing_the_harddisk_wit
Hi all,
From yesterday at the log of my M20 are the following message :
smartd[2595]: Device: /dev/ad1a, Failed attribute: (200)Write
Error Rate
It´s informative, but i think that there is a problem with my HDD ( I
still have to run the smartd commands ) .
Somebody had this pr
13 matches
Mail list logo
