Just curious, what type of tail wheel spring do you have. Wow everybody flying
but me.
Steve Bedford
Kr2s Builder
Sent from my LG Mobile
-- Original message--
From: Gary via KRnet
List-Post: krnet@list.krnet.org
Date: Sat, Oct 29, 2016 4:41 PM
To: KRnet;
Cc: Gary;
Problem with
t the side of the aircraft
caused a problem. Would a handle on top at the rear also cause a problem? If
someone with a better understanding could explain the aerodynamics. Thanks in
advance. I generally don't answer responses to keep the list cleaner and thanks
Mark for this list.
Steven Be
Mark,
This is a iefis g3 firmware upgrade from mgl?s website. I believe it was ported
to the g2 iefis what is probably what you have.
Hope this helps?.
Steve Bedford
Woodland Park, CO
www.mglavionics.co.za
1 December 2015 version A 1.0.2.6
Added: Spread spectrum clocking on all peripherals,
> I don't have that but I do have an extra corvair mount in my Hanger which I
> will turn loose $cheap$ just to get it outta my way.
>
> Mike Turner
> Edgewood, NM (1n1)
Mike, I would be interested in your corvair mount, you can email me personally.
Thank you,
Steven
and deform.
Study the plans and make sure you micro slurry the foam and squeegee the
cloth into the foam and make sure there is good contact between the spars
and resin/cloth.
Steven Bedford
Kr2s Builder
s1bedford at msn.com
ark's templates I don't think that it was much more than an 1/8"
difference using the recommended
parts on several builders websites.
Steven Bedford
Kr2s Builder
s1bedford at msn.com
believe
there is a flying kr super2. It was derived from the plans of a kr2s but
uses foam and fiberglass for the fuselage section instead of spruce and
plywood.
Steven Bedford
kr2s builder
s1bedford at msn.com
believe
there is a flying kr super2. It was derived from the plans of a kr2s but
uses foam and fiberglass for the fuselage section instead of spruce and
plywood.
Steven Bedford
kr2s builder
s1bedford at msn.com
acs and used aeropoxy resin. I would not be
concerned about buying the cloth from an aircraft supply store. I am a
fiberglass novice also but didn't have any problems laying up the horizontal
stab using Mark's clear plastic layup method. I recommend it, thanks again
Mark.
Steven Bedford
will check that when I get the engine on but shouldn't be a
problem.
That is a good note for the rest of us builders out there.
Thanks again,
Steven Bedford
Kr2s
-Original Message-
From: joe.kr2s.buil...@juno.com
Sent: Tuesday, November 22, 2011 4:21 PM
To: kr...@mylist.net
Subject: Fw: Re: KR
etups that are available with a factory nitrided
crank. If someone is interested you can email me off list.
Thanks for all the great info.
Steven Bedford s1bedf...@msn.com
Kr2s
etups that are available with a factory nitrided
crank. If someone is interested you can email me off list.
Thanks for all the great info.
Steven Bedford
Kr2s
Thank you for the information,
It is a 32mm aerocarb, 12 gallon RR fuel tank, stock cid corvair, and the
vent is a 5/16" aluminum tube
under the fuselage about an inch bent into the air stream.
Steven Bedford
Kr2s
a
problem with this carb. Should I be using just a vented cap instead.
Steven Bedford
Kr2s builder
Hello all,
I have a new left hand 58" 3 blade warp drive prop for sale with paper work and
protractor.
Contact me off list if interested. Thank you.
Steven Bedford s1bedf...@msn.com
Kr2s builder
Derek,
I just received my antenna kit Friday. I had ordered it back in March.
Steven Bedford
--
From: "Derek Lewis" <numskul...@netzero.net>
Sent: Monday, July 04, 2011 7:17 PM
To: <kr...@mylist.net>
Subject: KR> RST Engi
of the fuel tank.
I also have a freshly rebuilt subaru ea-81 turbo engine for sale that
came with my project if anyone is interested. Email me off list if
anyone is interested.
Thanks again
Steven Bedford
s1bedf...@msn.com
ught I
would ask. Good job on your wing tanks I have been following your progress.
Thanks
Steven Bedford
s1bedf...@msn.com
oe spars or would
I have to completely remove the old spars and start over? or install oil
impregnated bushings
into the existing 3 hinges and fly sooner?
Thanks in advance,
Steven Bedford
s1bedf...@msn.com
Jon,
Checkout Jeff Scott's website click on tail mods.
http://jscott.comlu.com/KR/KRmods.html
Was that your subarsonic in contact magazine? Very nice.
Steven Bedford
s1bedf...@msn.com
In search of a kr2s kit or project
--
From: "Jon Finle
Mark, sorry for the late response, checkout anywheremap.com I bought the
software when it was $90 and used a older hp pocket pc. I believe it runs
on
a pc with the correct version of software. I run mine with a wireless
bluetooth gps reciever.
Steven Bedford
In search of a Kr2s kit
Hello Walt,
I would be interested in the kr-2 spruce kit and plywood. Has anyone made a
firm agreement of picking it up?
Where in Texas are you located? You can email me at s1bedf...@msn.com.
Thanks
Steven Bedford
> Long story short--I have asked for and received help in trying to ident
Hello Walt,
I would be interested in the kr-2 spruce kit and plywood. Has anyone made a
firm agreement of picking it up?
Where in Texas are you located? You can email me at s1bedf...@msn.com.
Thanks
Steven Bedford
> Long story short--I have asked for and received help in trying to ident
Hello all, My name is Steven Bedford I am new to the list
I also have sent a cashiers check for kr2s plans set to Rand Robinson.
I am not in a hurry due to the cold winter but it has been 10 weeks.
Thanks for all the great information that is available from this list
and builder websites.
24 matches
Mail list logo