plex gear in both the fine and the medium gear sets is the same
>> gear that I made the tooth numbers you can get by counting the teeth of the
>> legacy gears I showed you said you had the standard gear set ,the index
>> gear of my medium gear package is legacys .25 gear set index
ber of the teeth on the little index gear
> is15 teeth
>
>
>
> Bill
>
>
>
> *From:* legacy-orna...@googlegroups.com *On
> Behalf Of *cdkr...@gmail.com
> *Sent:* Thursday, September 7, 2023 11:43 AM
> *To:* Legacy Ornamental Mills
> *Subject:* Re: Verification of underst
the tooth count I will send later I’m not in my shop now I will have to count
them the number of the teeth on the little index gear is15 teeth
Bill
From: legacy-orna...@googlegroups.com On
Behalf Of cdkr...@gmail.com
Sent: Thursday, September 7, 2023 11:43 AM
To: Legacy Ornamental Mill
t in my shop now I
> will have to count them the number of the teeth on the little index gear
> is15 teeth
>
>
>
> Bill
>
>
>
> *From:* legacy-orna...@googlegroups.com *On
> Behalf Of *cdkr...@gmail.com
> *Sent:* Thursday, September 7, 2023 11:43 AM
>
: Legacy Ornamental Mills
Subject: Re: Verification of understanding
Bill, you did such a professional job I thought those gears were produced at
the factory! That combined with my bad memory of what you said at the time. My
bad.
I understand that you modeled your duplex gears after
d the small tooth side is
>> the number of teeth from a standard duplex gear I modelled my fine gear
>> set duplex gear from those 2 gears 😊
>>
>>
>>
>> Bill
>>
>>
>>
>> *From:* legacy-orna...@googlegroups.com
>> *On Behalf
fine gear
> set duplex gear from those 2 gears 😊
>
>
>
> Bill
>
>
>
> *From:* legacy-orna...@googlegroups.com *On
> Behalf Of *cdkr...@gmail.com
> *Sent:* Thursday, September 7, 2023 8:19 AM
> *To:* Legacy Ornamental Mills
> *Subject:* Re: Verific
Of cdkr...@gmail.com
Sent: Thursday, September 7, 2023 8:17 AM
To: Legacy Ornamental Mills
Subject: Re: Verification of understanding
Ha! I understand like a grown up! So you made custom gearsh.
So, in the picture of the fine gear set, there are two gears stacked to the
right of
, September 7, 2023 2:08 AM
To: Legacy Ornamental Mills
Subject: Re: Verification of understanding
These medium and fine gear sets were from a post here in the past. I don't
know what LOM model they fit, but I included them on my chart because that what
the original spreadsheet from here had
;>> course to make a fine V thread if I wanted.
>>>
>>>
>>>
>>>
>>>
>>> Bill
>>>
>>>
>>>
>>>
>>>
>>> *From:* legacy-orna...@googlegroups.com
>>> *On Behalf Of *cdkr...@gmail.c
ine V thread if I wanted.
>>
>>
>>
>>
>>
>> Bill
>>
>>
>>
>>
>>
>> *From:* legacy-orna...@googlegroups.com
>> *On Behalf Of *cdkr...@gmail.com
>> *Sent:* Wednesday, September 6, 2023 11:08 PM
>> *To:*
gt;
> *From:* legacy-orna...@googlegroups.com *On
> Behalf Of *cdkr...@gmail.com
> *Sent:* Wednesday, September 6, 2023 11:08 PM
> *To:* Legacy Ornamental Mills
> *Subject:* Re: Verification of understanding
>
>
>
> This chart should look familiar. This is where I f
of an inch pitch the .25 gears and the C gear cut a one
> inch pitch not 1/6 please enlighten me what am I not seeing? As far as I
> can tell you would need some serious math and work out what tooth drive
> gear needs to be cut to mill a 1/6 inch pitch
>
>
>
> Bill
>
>
eeing? As far as I can tell you
would need some serious math and work out what tooth drive gear needs to be cut
to mill a 1/6 inch pitch
Bill
From: legacy-orna...@googlegroups.com On
Behalf Of cdkr...@gmail.com
Sent: Wednesday, September 6, 2023 8:18 AM
To: Legacy Ornamental Mills
Subje
ot 1/6 please enlighten me what am I not seeing? As far as I
>> can tell you would need some serious math and work out what tooth drive
>> gear needs to be cut to mill a 1/6 inch pitch
>>
>>
>>
>> Bill
>>
>>
>>
>> *From:* legacy-orna...@goog
ear needs to be cut
to mill a 1/6 inch pitch
Bill
From: legacy-ornamental-mills@googlegroups.com
On Behalf Of cdkr...@gmail.com
Sent: Wednesday, September 6, 2023 8:18 AM
To: Legacy Ornamental Mills
Subject: Re: Verification of understanding
Bill, the wooden thread TPI used most commonly
needs to be cut
to mill a 1/6 inch pitch
Bill
From: legacy-ornamental-mills@googlegroups.com
On Behalf Of cdkr...@gmail.com
Sent: Wednesday, September 6, 2023 8:18 AM
To: Legacy Ornamental Mills
Subject: Re: Verification of understanding
Bill, the wooden thread TPI used most
Oh I get it now I see it upside down lol
Bill
From: legacy-ornamental-mills@googlegroups.com
On Behalf Of cdkr...@gmail.com
Sent: Wednesday, September 6, 2023 8:18 AM
To: Legacy Ornamental Mills
Subject: Re: Verification of understanding
Bill, the wooden thread TPI used most
k in the day was usually
>> a 90 degree V not 60 degree and the threads per inch would be 1.3 if I’m
>> doing my math right.
>>
>>
>>
>> Bill
>>
>>
>>
>> *From:* legacy-orna...@googlegroups.com
>> *On Behalf Of *cdkr...@gmail.com
>>
ter bit ? a wooden v thread back in the day was usually
> a 90 degree V not 60 degree and the threads per inch would be 1.3 if I’m
> doing my math right.
>
>
>
> Bill
>
>
>
> *From:* legacy-orna...@googlegroups.com *On
> Behalf Of *cdkr...@gmail.com
>
@googlegroups.com
On Behalf Of cdkr...@gmail.com
Sent: Wednesday, September 6, 2023 1:47 AM
To: Legacy Ornamental Mills
Subject: Verification of understanding
Hi everyone,
I've been studying all the related pitch information I can find and have
accumulated this into a condensed spreadsheet workbook
Hi everyone,
I've been studying all the related pitch information I can find and have
accumulated this into a condensed spreadsheet workbook with four sheets for
my use with the REVO. I struggled to understand how the various pitches
were arrived at until I finally reduced it to basic specifica
22 matches
Mail list logo