I don't know whether 3.3.6 is included with RH 7.3 (it was with all the previous RH
7.x) If it is
you can do as Shane suggested BUT in /etc/X11 NOT in /usr/X11R6/bin (at least in my RH
setup this
is the one which is used...). However, the config file is not anymore the same...
Theoretically
you
I've just upgraded, and have it working fine on my laptop,
but am unable to get anything other than a blank or blinky
screen on my NEC MultiSync LCD1700V monitor. The old
config, which worked under 3.3.6, is attached.
Any insights into how to make this work?
Thanks,
Michael
XF86Config
Desc
the ones included with distributions sometimes don't work perfectly, more
likely to have wider chip coverage if you download X separately, i got it
with slackware and it pooped, i downloaded separate and it works better,
not perfectly, but still. if you try a download of an older version it mig
Hi,
I've installed the NVidia GLX and kernel drivers from the tar
files and everything seems to be set up as described in the installation
instructions provided by NVidia. However X fails to start and my
XFree86.0.log file has the following tail:
(II) NVIDIA(0):
AGP 4X successfully
On Thursday 13 June 2002 7:31 am, [EMAIL PROTECTED] wrote:
> Thanks for your help, but the mouse is still not fully working:
> > If the wheel itself is also a button, you have 3 buttons? The wheel
> > needs 2 extra buttons so you should have;
> > Option "Buttons" "5"
> >
Hi,
I am trying to compile V4.2.0, and on one system I dont have 'cc'
installed. "cc: command not found" What IS this when it's on the dist'
(RH7.3).
Shane
___
Newbie mailing list
[EMAIL PROTECTED]
*** To unsubscribe , or change message options, see:
Dude, this is an XFree86 mailing list! ;)
On Wed, 19 Jun 2002 23:23:47 -0500
Royce Wise <[EMAIL PROTECTED]> wrote:
> Anyone know of a list or mail group for assembly language programing
> for FREEBSD?
> Royce
___
Newbie mailing list
[EMAIL PROTECTED]
--- Lionel Lecoq <[EMAIL PROTECTED]> wrote:
> have you tried 3.3.6?
Umm 3.3.6 what? Sorry but I couldnt get which sw you
mean. The Xfree86 is the version bundled with RH7.3
Thanx for your replies
Spundun
> Lionel
__
Do You Yahoo!?
Yahoo! - Officia
Try what I did earlier today. In /usr/X11R6/bin, replace the
softlink X -> XFree86 with -> XFree86_SVGA. Check that the SVGA server
exists, and install the rpm if it doesn't.
This very simply forces the system to use the 3.3.? server.
Shane
> > > -Original Message-
> > > From: [
It probably isn't much help in this case, but I much prefer
Xconfigurator.it gives YOU the option of selecting different
devices/resolutions/speeds, rather than just reading defaults for your
detected hardware.
Shane
Lionel Lecoq wrote:
>
> have you tried 3.3.6?
> Lionel
> --- Cary Pembleto
PS...
post your XF86Config
and while waiting try using the vesa driver (hack the conf file)
Lionel
--- Spandan Bhatt <[EMAIL PROTECTED]> wrote:
> Platform:RH 7.3
> Device:S3 savage pro chipt set:8d04
> (On motherboard)
>
> I have reformatted the partition and installed lates
> Linux on it and aft
It would be interesting to know which version of X you run (if it's 3.3.x then your
card may be
not supported...) I don't know freeBSD well enough to be of more help as to where the
log is
stored (in Linux it's in /var/log/XFree86.0.log on top is the version number) doing X
-version (in
Linux)
have you tried 3.3.6?
Lionel
--- Cary Pembleton <[EMAIL PROTECTED]> wrote:
> I had a heck of a hard time with that one too. I finally gave up and just bought a
>NVIDIA
> Gforce. It was cheap and did the job. Sorry I can be of no more help than this.
>
>
> -Original Message-
> From: [EMA
Hmm... It might be worth noting, that quite some time
ago I had a similar problem with Mandrake 7.1 being
incredibly draggy (this was with an nVidia Riva TNT2
and XFree86 3.3.6 though). Recompiling the kernel from
vanilla sources fixed it. Try rebuilding first the
kernel, then X, from source. (Can
Imake.tmpl is in directory /usr/X11R6/bin/imake and /usr/bin/X11/imake
PC Networks, Inc. and KY4U, LLC
Cary Pembleton
32 Cove LN
Campbellsville, KY 42718
270-469-4405 Office
270-469-9104 Fax
270-403- Corporate Cell (Corporate Business Only)
mailto:[EMAIL PROTECTED] E-Mail Address
http://www.k
BioChem33, I have a similar problem, take a
look at it:
http://www.nvnews.net/forum/showthread.php?s=&threadid=15640
Trying to resolve now with not very good
future.
Cheers.
cHaMaY
Red Hat 7.3
Kernel 2.4.18-4
-
ZAAPA ZP/3VAAV ATX VIA F
Via
16 matches
Mail list logo
