Re: [Repeater-Builder] duplexer pages

That's the one!! Mathew Quaife wrote: Which one do you need?  I have one for the 28-37-2a if needed.   Mathew John Place <[EMAIL PROTECTED]> wrote: Was looking at the site and looking down at the duplexer tuning sheets for the different ones, Wacomm, Sinclair, etc., but di

Re: [Repeater-Builder] Re: system board GE MASTR II

ok Brent if anyone needs uhf receivers i have some ,5 or 6 to spare , gervais,ve2ckn >From: "Brent" <[EMAIL PROTECTED]> >Reply-To: Repeater-Builder@yahoogroups.com >To: >Subject: Re: [Repeater-Builder] Re: system board GE MASTR II >Date: Sat, 7 May 2005 21:15:04 -0500 > >It is a UHF >

Re: [Repeater-Builder] Re: system board GE MASTR II

It is a UHF And Sorry Coy for the poor info and details ... I also have the molex connectors and everything all wired and ready to go just missing a system board. factory complete. all wires are intact just nothing to plug them into. - Original Message - From: "gervais fillion" <[EMAIL PRO

Re: [Repeater-Builder] system board GE MASTR II

Hi Brent: I have a "LIKE NEW" system board that i will sell. E-Mail me off list at [EMAIL PROTECTED] Thanks, Bill N8LXM Brent wrote: >Anybody know where I can locate a system board for a Ge Mastr II repeater >I think the numbers are as follows 19D417205P1 Rev 3 > > >Thanks >Brent > > > >--- >[Th

RE: [Repeater-Builder] Re: system board GE MASTR II

Brent your master 2 is Uhf or Vhf ? 73/s to all here at the group! gervais,ve2ckn >From: "Coy Hilton" <[EMAIL PROTECTED]> >Reply-To: Repeater-Builder@yahoogroups.com >To: Repeater-Builder@yahoogroups.com >Subject: [Repeater-Builder] Re: system board GE MASTR II >Date: Sun, 08 May 2005 02:05:42 -

[Repeater-Builder] Re: system board GE MASTR II

Okay let me see if I have it. What you have is an exciter and a PA (A transmitter only). A receiver from another base or mobile. No system board. Okay, If you can't find a replacment receiver system board, let me know, I'll help you with a work around. At least you have the 10 V regulator in th

Re: [Repeater-Builder] Re: system board GE MASTR II

well I have acquired another Ge Repeater with out the receiver, and I have a receiver but the repeater I acquired no only was missing just the receiver but the actual whole tray, the complete fold out osc, sq/audio board and system board.. Oh no, no bad 10v reg card .. the control shelf is in tac

[Repeater-Builder] Re: system board GE MASTR II

Are you building a radio or, do you have a bad 10 Volt regulator? There are work arounds if you can't find one. Good luck Bret --- In Repeater-Builder@yahoogroups.com, "Brent" <[EMAIL PROTECTED]> wrote: > Anybody know where I can locate a system board for a Ge Mastr II repeater > I think the nu

Re: [Repeater-Builder] duplexer pages

Which one do you need?  I have one for the 28-37-2a if needed.   Mathew John Place <[EMAIL PROTECTED]> wrote: Was looking at the site and looking down at the duplexer tuning sheets for the different ones, Wacomm, Sinclair, etc., but didn't see anything for tuning the txrx series. Nobody have any

Re: [Repeater-Builder] Motorola GTX

At 01:00 PM 5/7/2005, Mike Mullarkey wrote: I have some 900 MHz GTX mobile radios and I seem to have the older software and need the newer version. I have the 01 & 02 version. Does anybody have the newest version for these radios. how do you know which version you need? I also have GTX's but ha

[Repeater-Builder] 1.2 g handheld

Anyone know where I can get a clean Standard C628A twin-band handheld? Don Yahoo! Groups Links <*> To visit your group on the web, go to: http://groups.yahoo.com/group/Repeater-Builder/ <*> To unsubscribe from this group, send an email to: [EMAIL PROTECTED] <*> Your use of Yaho

[Repeater-Builder] system board GE MASTR II

Anybody know where I can locate a system board for a Ge Mastr II repeater I think the numbers are as follows 19D417205P1 Rev 3 Thanks Brent --- [This E-mail scanned for viruses at TNWEB LLC] Yahoo! Groups Links <*> To visit your group on the web, go to: http://groups.yahoo.com/grou

Re: [Repeater-Builder] duplexer pages

Don't know about txrx. but tell me where you found Sinclair, also I have tuned Wacomms the txrx should not be much different. Bruce. KD4BOH. - Original Message - From: "John Place" <[EMAIL PROTECTED]> To: "Repeater-Builder" Sent: Saturday, May 07, 2005 10:54 AM Subject: [Repeater-Builder

[Repeater-Builder] Motorola GTX

I have some 900 MHz GTX mobile radios and I seem to have the older software and need the newer version. I have the 01 & 02 version. Does anybody have the newest version for these radios.   Thanks  Mike   Oregon Repeater Linking Group Mike Mullarkey 6539 E Street Springfield, OR 974

[Repeater-Builder] Low-Pass Filters for Ferrite Isolators

Steve, There is nothing special about the low-pass filter that might require you to use a particular brand name. A ferrite isolator is a nonlinear device, and therefore it will generate a strong second harmonic which must be attenuated by either a notch filter or a low-pass filter. Notch filt

Re: [Repeater-Builder] Re: Looking for Microwave Associates 7R011T Isolator Tuning Procedure

Steve: The low pass filter is a D4066 and I have found them in flea markets and bought one at Dayton for not much money, but that was many years ago. I have never opened one up, but it is a harmonic low pass filter intended to make up for the distortion of rf going through the isolator. I th

Re: [Repeater-Builder] Spectra-Tac RX cable

Bob, The TKN6759A cable has identical seven-pin male plugs on both ends. It is used in SpectraTAC satellite and remote receivers to connect the metering test jack on a MICOR Sensitron receiver board to the backplane of the SpectraTAC unit, so that the receiver functions can be monitored on the Sp

Re: [Repeater-Builder] Spectra-Tac RX cable

Howdy Is this the small connectors or the large connectors for the micor chassie ? ..bob Kevin Berlen, K9HX" wrote: > I am looking for a TKN6759A cable for a Spectra-Tac receiver. This > cable allows a receiver service module to take meter readings from > the receiver RF-IF board installed

Re: [Repeater-Builder] Re: Looking for Microwave Associates 7R011T Isolator Tuning Procedure

Where would one expect to find the low pass filters to use with this isolator? If they are hard to find or are expensive, does anyone have a LPF design the can share which is capable of 50W on 70cm which can be constucted in a die cast aluminum box? I have an ridiculously expensive and bulky K&L

Re: [Repeater-Builder] Re: Looking for Microwave Associates 7R011T Isolator Tuning Procedure

Skipp: Actually, I have two different versions of the same catalog, one is in a red plastic custom binder, the other is a metal binder with cardboard covers. No need to pay for scans.  You have credit because you sent me some photocopies of various circuits that you had many years ago.

[Repeater-Builder] duplexer pages

Was looking at the site and looking down at the duplexer tuning sheets for the different ones, Wacomm, Sinclair, etc., but didn't see anything for tuning the txrx series. Nobody have any? -- No virus found in this outgoing message. Checked by AVG Anti-Virus. Version: 7.0.308 / Virus Database

[Repeater-Builder] Re: Looking for Microwave Associates 7R011T Isolator Tuning Procedure

Don't ever throw that catalog out... If it was worth your time, I'd pay you for some photocopies or page scans. thanks skipp > Micheal Salem <[EMAIL PROTECTED]> ,wrote: > Skip: > > I did look it up when I got home in my ancient M/A-COM > catalog (From 1982, no less. It is hard to throw this

RE: [Repeater-Builder] TKR-820 and the Kenwood KPT-20 Programmer

Mark,   I have one of these programmers also!  I will be interested in any responses!   Paul     -Original Message-From: Repeater-Builder@yahoogroups.com [mailto:[EMAIL PROTECTED]On Behalf Of N9WYSSent: Friday, May 06, 2005 7:01 PMTo: Repeater-Builder@yahoogroups.comSu

Re: [Repeater-Builder] Spectra-Tac RX cable

Kevin, You can purchase the ready-made cable #TKN6759A from Motorola Parts for $ 26.99 each, or you can make your own cable with six wires and two #2884208B01 plugs at $ 2.61 apiece. The SpectraTAC service manual #6881039E45 is still available at just $ 9.78 each- a real bargain. 73, Eric Lemmon

Re: [Repeater-Builder] Converting Use of Duplexer from SingleAntenna to Split Antenna?

a TEE ??? ok when you want both antennas to XMIT & Recieve at the same time a Tee is designed for that purpose, but for repeater that will not fly ! My sugguestion the ARRL Handbook and some primer on repeaters, this stuff is on the Extra Exam BTW Mark Holman [EMAIL PROTECTED] http://www.ab8

Re: [Repeater-Builder] Looking for Microwave Associates 7R011T Isolator Tuning Procedure

At 06:36 PM 5/6/05, you wrote: >Micheal Salem wrote: > > >As a matter of fact, They are attached. > > > >I have uploaded the 7R011 Tuning Instructions to RBTIP. Maybe Mike >Morris would be so kind to add a link or index so folks can find them. >