Re: ShopTalk: putter pendulum tester

2003-09-01 Thread Dave Tutelman
At 11:16 PM 8/27/03 -0400, [EMAIL PROTECTED] wrote: I find myself in need of a putter pendulum tester. Im hoping someone might have access to one I could borrow, rent, or buy. Possibly someone might have plans for one I could build, or someone could create said plans for a fee or barter. David Dav

ShopTalk: WOW!

2003-09-01 Thread Arniesclubs
And all I said was I use Devcon 5 minute epoxy? Did I miss something here? Yes, you missed what is below. You wrote that you use this on graphite shafts not on steel and as I hope you see, the 5 minute cure stuff is not as strong as the longer cure stuff. That's why the 5 minute cure is prone to

RE: ShopTalk: Ping putter w/ ball bearing

2003-09-01 Thread Royce Engler
Hi Keith... If you have to drill it out, use a small drill to come in from the bottom of the hosel. Use a drill bit that matches your smallest pin punch or in a pinch, a finishing nail will do the trick. Drill the hole and use the pin punch to drive the ball out the shaft end. You should then b

RE: ShopTalk: Ping putter w/ ball bearing

2003-09-01 Thread Donald Johnson
Keith: Some folks have had success in drilling out the ball I have not so turn it over and drill a small hole in the hosel and punch out the ball. Fill the hole with epoxy and buff it smooth you will never see it while you're putting. Don Johnson -Original Message- From: [EMAIL

ShopTalk: Ping putter w/ ball bearing

2003-09-01 Thread Keith E. Anderson
Aloha all! I have a ping putter, with the ball bearing, broken off at the hosel. I am going to try the freezing method I've read about here, but I don't have any shaft to put in my puller, and my #4 extractor wont fit snug because of the ball bearing. Any tips? I was brainstorming and thought a

RE: ShopTalk: Re: why bother?

2003-09-01 Thread Mark A Patton
LOL Tom. tell us how you feel Mark A Patton [EMAIL PROTECTED] -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] Behalf Of tflan Sent: Monday, September 01, 2003 2:37 PM To: ShopTalk Subject: Re: ShopTalk: Re: why bother? Hey! Screw Arnie

Re: ShopTalk: Re: why bother?

2003-09-01 Thread tflan
Hey! Screw Arnie! Who the hell is he? A friggin' golf club assembler. What's his station? Pariah? Moses? If a person has an opinion he should voice it without some asshole who thinks he's the only goddam clubmaker who ever "graced" these pages insulting his opinion. Look y'all. What's so goddam

ShopTalk: Golf Meditations

2003-09-01 Thread Robert Baxter
*Golf Meditations* If you really want to get better at golf, go back and take it up at a much earlier age. The game of golf is 90% mental and 10% mental. Since bad shots come in groups of three, a fourth bad shot is actually the beginning of the next group of three. When you look up, causing an a

Re: ShopTalk: Re: why bother?

2003-09-01 Thread Burgess Howell
Don't get Arnie pissed. At 07:24 PM 8/31/03, you wrote: And all I said was I use Devcon 5 minute epoxy? Did I miss something here? --- [EMAIL PROTECTED] wrote: > Go to http://www.devcon.com/techinfo/adhphy.pdf and > you will see that 5 > minute has strength of 1400 psi vs 2400 psi for 10 > minu

Re: ShopTalk: Re: why bother?

2003-09-01 Thread Dan Allan
And all I said was I use Devcon 5 minute epoxy? Did I miss something here? --- [EMAIL PROTECTED] wrote: > Go to http://www.devcon.com/techinfo/adhphy.pdf and > you will see that 5 > minute has strength of 1400 psi vs 2400 psi for 10 > minute > > I will only use 5 minute stuff for bore through