ShopTalk: Fw: Unable to deliver your message

I have been unable to post a message to the shoptalk group. Robert Latta --- On Fri, 12/18/09, Yahoo! Groups wrote: From: Yahoo! Groups Subject: Unable to deliver your message To: rlatt...@yahoo.com Date: Friday, December 18, 2009, 9:38 AM We are unable to deliver the message from to .

Re: ShopTalk: True Temper Stepless Blanks

Thanks for checking. Do you have a suggestion for a similar shaft? I have some rifles around here that I could use but wanted to match my friends shafts. I re-shafted his Calloway irons about a year and a half ago and he lost his 7 and 8 irons. How much would 50 cost? Thanks, Rob On 4/30/07

Re: ShopTalk: True Temper Stepless Blanks

Hi David, thanks for getting back with me. I only need 2 at the moment but would like to get 12...2 for now and 10 more for my next set of irons. Got some? Rob On 4/27/07, [EMAIL PROTECTED] <[EMAIL PROTECTED]> wrote: In a message dated 4/27/2007 10:17:08 PM Pacific Daylight Time,

ShopTalk: True Temper Stepless Blanks

Hello All, About a year and a half ago I bought some True Temper stepless shaft blanks. I can't for the life of me remember where I got them so I searched the internet and still had no luck finding them. Anyone here know where I might find some? Thanks Rob

Re: ShopTalk: Square Drivers?

Hello All, About a year and a half ago I bought some True Temper stepless shaft blanks. I can't for the life of me remember where I got them so I searched the internet and still had no luck finding them. Anyone here know where I might find some? Thanks Rob

Re: ShopTalk: Square Drivers?

Hello All, About a year and a half ago I bought some True Temper stepless shaft blanks. I can't for the life of me remember where I got them so I searched the internet and still had no luck finding them. Anyone here know where I might find some? Thanks Rob ReThink Solar

Re: ShopTalk: RE: The case for spine finders, (was shaft flex v.s. frequency)

I just created a special folder under my Shop Talk Inbox folder called "Hall of Fame"  and moved this article into it.   Thomson, Jim wrote: Great post ! I've been a member of Spinetalkers Forum for a couple of years and Shoptalk for about a year and I think this is the best (and most con

Re: ShopTalk: RE: The case for spine finders, (was shaft flex v.s.frequency)

Dan, Is there a place online that gives instructions on how to build a Neu-finder?  Or, pictures of one of these devices? Thanks   Dan Neubecker wrote: All, I have enjoyed the discussion of spines and devices to find them. I believe we have missed some critical considerations in this disc

ShopTalk: Definitions of a "cut and gluer"?

experienced club makers to describe a novice who doesn't know as much as he should about the science of it all. Just curious, Rob

ShopTalk: Reshafting Mizuno TZoid Irons with parallel tip shafts

Hi, Sorry to beat a dead horse but does anyone know anything to watch out for when reaming Mizuno irons from taper to parallel? Do I have to start with a smaller reamer and work up to the .370? I don't have the reamers yet...will I be ok ordering must one .370? Thanks in advance. Rob

Re: ShopTalk: Walter Hagen Clubs

Could someone reprint the post where RK was writing about the reamers to go from taper to parallel irons? Or, forward the link. I'd like to have that capability. Thanks! Rob Campbell Harry F. Schiestel wrote: Hi Jack and Jents For leather grips check out http://www.thegripmaste

Re: ShopTalk: Frequency slope

too stiff.  When I miss hit a shot it tends to go left unless of course I block it.  I'd also like to be a better chipper.  I know what that means though. :-) Rob Campbell     ---Original Message---   From: [EMAIL PROTE

ShopTalk: Frequency slope

frequency slope do most of you use when building custom clubs? Rob Campbell   IncrediMail - Email has finally evolved - Click Here

ShopTalk: Soft stepping

What is soft stepping?  I think I have an idea.  Why not go with a softer (more flexible shaft?) to begin with?  Rifle 4.5etc. Rob     >>>I have TFR Rifle shafts (5.0 soft stepped once) The 5.0's were a bit too&

Re: ShopTalk: Forged iron comparison

Thank You! Rob   ---Original Message---   From: [EMAIL PROTECTED] Date: Monday, July 01, 2002 7:10:19 AM To: [EMAIL PROTECTED] Subject: Re: ShopTalk: Forged iron comparison  Rob It is

Re: ShopTalk: Forged iron comparison

This sounds like a great club.  Does anyone know if there is a web site out there that has pictures and specs of these irons?  I did a search for Infinity Golf and came up empty. Thanks     ---Original Message---   From:

Re: ShopTalk: Driver Puzzle

he AJ Tech Z Tour 90 shaft and smoked it to the back center of the range.  I really did not like the feel of the EI-70.  No science there, just a similar experience with that shaft. Rob Campbell      ---Original Message---   From: [

Re: ShopTalk: MacGregor web site

Hi Pat, The website is: http://www.macgregorgolf.com/   I used a search engine and searched for "Macgregor". Rob     ---Original Message---   From: [EMAIL PROTECTED] Date: Tuesday, June 18,

Re: ShopTalk: KZG components

What component companies sell good quality forged iron heads?  I know about Golfsmith but are there any others out there?  Thanks. Rob       >>>>>>There's a hell of a lot of heads out there in the market that a

Re: ShopTalk: KZG components

KZG only sells direct to their authorized dealers.  This is what they told me via email.  If you know otherwise...please enlighten. Thanks Rob    ---Original Message---   From: [EMAIL PROTECTED] Date: Thursday

RE: ShopTalk: KZG components

anyone sell only the heads? Or, does anyone here know anyone who will? Thanks, Rob     > Subject: ShopTalk: KZG components>>>> Who sells KZG heads. I need to find a 12 degree dri