Actually, 'IT' was quite dirty to start with.
I try to stay clean.
Joe
-Original Message-
From: time-nuts-boun...@febo.com [mailto:time-nuts-boun...@febo.com] On
Behalf Of J. L. Trantham
Sent: Saturday, August 29, 2009 11:16 PM
To: 'Discussion of precise time and frequency measurement'
S
I recently purchased a 5065A that did not work but was 'fixed' by unseating
all the PC cards and reseating them. I was quite dirty to start with
though.
Joe
-Original Message-
From: time-nuts-boun...@febo.com [mailto:time-nuts-boun...@febo.com] On
Behalf Of Stan
Sent: Saturday, August 29
Hi Tim - I don't have the app note, but the HP Journal article is on line
at, among many locations:
http://www.gamearchive.com/General/Test_Equipment/HP/HPJMay77.pdf
Regards, John K1AE
PS: I think that the availability of logic analyzers in the late 70's may
have affected the adoption of signa
I have placed a scanned manual for the HP5245L frequency counter at
http://www.kennethkuhn.com/hpmuseum/scans/
Brian - KD4FM
___
time-nuts mailing list -- time-nuts@febo.com
To unsubscribe, go to https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts
Anyone happen to know where to find a service manual for a 1998? I already
have a users manual.
I also like to put my hands on such a document!
73, Alf OH2QM
___
time-nuts mailing list -- time-nuts@febo.com
To unsubscribe, go to https://www.febo.com/
Stan,
I'd recommend putting it in open loop and removing top and bottom covers.
Place on it's left side and hook a scope to the tp1 test point on the
bottom of the A7 assy. (.5v/cm)
Place the scope synch in external and use the variable time base ajust in
conjunction with time base step switch t
Hi Stan,
It gets like a broken record, but the first place I always go when a
formerly working piece of test equipment stops working is the power
supply.
Check the power supply voltages for both value, and ripple.
Then check all of the electrolytic capacitors for ESR. It only takes
one, in a l
I have a "late model" (s/n 2816A01565) 5065A that had been running fine for
quite a while in my lab at home. About two years ago I had to power it down
and store it away in climate-controlled storage during a remodeling project.
Last night I got it back out of storage and powered it up. Initially,
Magnus Danielson wrote:
swingbyte wrote:
Poul-Henning Kamp wrote:
In message <72c46d68028c463ebdb775ee14fb9...@laptop>, "Roy Phillips"
writes:
Tim
I have recently acquired a 5370B and find your comments of
interest. So in addition, what was the intention of designing the
mother-board to ha
swingbyte wrote:
Hi all,
I have looked through the archives and found that the 5370B has a better
front end and dacs and consolidated the ram and mpu onto one card.
However, can someone tell me how much better? these changes make the
5370B?
It is my understanding that the changes in the B m
At 04:25 AM 8/29/2009, swingbyte wrote...
What effect upon measurements does the new front end have over that
of the 5370A?
The input changes affected the /1 input dynamic and operating ranges.
100 mV - 1.0 V / -2.5 - 1.0 V p-p vs. 100 mV - 4.0 V / -4.0 - 4.0 V
p-p.
Does it mean significan
swingbyte wrote:
Poul-Henning Kamp wrote:
In message <72c46d68028c463ebdb775ee14fb9...@laptop>, "Roy Phillips"
writes:
Tim
I have recently acquired a 5370B and find your comments of interest.
So in addition, what was the intention of designing the mother-board
to have no less than three add
In a message dated 29/08/2009 13:18:16 GMT Daylight Time,
swingb...@exemail.com.au writes:
p.s. Did my original post make the newsgroup, or just one person?
Hi Tim
It made it to the list, just not many answers yet:-)
regards
Nigel
GM8PZR
_
Poul-Henning Kamp wrote:
In message <72c46d68028c463ebdb775ee14fb9...@laptop>, "Roy Phillips" writes:
Tim
I have recently acquired a 5370B and find your comments of interest. So in
addition, what was the intention of designing the mother-board to have no
less than three additional (and in m
In message <72c46d68028c463ebdb775ee14fb9...@laptop>, "Roy Phillips" writes:
>Tim
>I have recently acquired a 5370B and find your comments of interest. So in
>addition, what was the intention of designing the mother-board to have no
>less than three additional (and in my case,unused) pcb slots fo
Tim
I have recently acquired a 5370B and find your comments of interest. So in
addition, what was the intention of designing the mother-board to have no
less than three additional (and in my case,unused) pcb slots following the
uP and Display interface, marked ROM, MEM(optional) and SERVICE(AID
Hi all,
I have looked through the archives and found that the 5370B has a better
front end and dacs and consolidated the ram and mpu onto one card.
However, can someone tell me how much better? these changes make the
5370B? What effect upon measurements does the new front end have over
that
17 matches
Mail list logo