List,
I am selling my Austron 1250A. The meter readings are all in the OK range and
has a 5 MHz output which I've not calibrated. It's in good cosmetic condition.
It comes with the factory manual,extender board, relay rack mounting brackets,
spare fuses and a AN connector for attaching an
To: time-nuts@febo.com
Subject: [time-nuts] Austron 1250A Tuning tool
Hello
My 1250A has drifted outside the range of the front panel control, so the
coarse adjust needs some fiddling. The manual makes mention of a special
tool to be used for this. I don't have the tool, the closest I can get is a
10
Fantastic, just what I needed. A little gentle persuasion with a knife
coaxed one of my crappy screwdrivers blade to become long enough (or
rather, the handle short enough..) to fit. 5 minute job once I knew what is
on the other end. Thank you!
OleP
___
5:56 AM
To: Discussion of precise time and frequency measurement
Subject: Re: [time-nuts] Austron 1250A Tuning tool
I adjusted my 1250A using a 1/8 brass rod that I got from the hardware store.
I filed down the end to make it into a screwdriver. This worked fine. I could
tell when the tip
Thanks all
I decided to replace the batteries, expecting delivery any minute now.
Surprisingly expensive to replace those NiCd's.. Anyway, after looking at
the schematics a bit, I was able to stop the relay chatter by setting the
unit to charge, and holding down the reset switch for a couple of
Hello
My 1250A has drifted outside the range of the front panel control, so the
coarse adjust needs some fiddling. The manual makes mention of a special
tool to be used for this. I don't have the tool, the closest I can get is a
10 bamboo stick that I cunningly liberated from my wifes sushimaking
-5960 office
908-902-3831 cell
-Original Message-
From: time-nuts [mailto:time-nuts-boun...@febo.com] On Behalf Of Ole Petter
Ronningen
Sent: Wednesday, February 18, 2015 12:47 PM
To: time-nuts@febo.com
Subject: [time-nuts] Austron 1250A
Hello
On a whim I purchased an Austron 1250A off
, February 18, 2015 9:47 AM
To: time-nuts@febo.com
Subject: [time-nuts] Austron 1250A
Hello
On a whim I purchased an Austron 1250A off of eBay, tested for power on only.
I somehow doubt they told the whole truth there, as the unit makes a
*very* noticable buzzing sound when powered on!
The sound
chatter. The crystals are well aged now :-))
Alan
G3NYK
- Original Message -
From: Ole Petter Ronningen olep...@gmail.com
To: time-nuts@febo.com
Sent: Wednesday, February 18, 2015 5:46 PM
Subject: [time-nuts] Austron 1250A
Hello
On a whim I purchased an Austron 1250A off of eBay, tested
Ole
I will guess that without the pack the bus voltage may go high and that
they also used the pack as a filter cap. So you should be able to find a
free manual on one of the sites. KO4BB is a good guess. It may be as simple
to start as a 10,000 uf cap to get going. The oscillating relay may be 60
I have a virgin 5 MHz secondary frequency standard to sell. Before I go the
eBay route, I thought I would post it here. Contact me off-list if
interested.
-Doug Ronald
___
time-nuts mailing list -- time-nuts@febo.com
To unsubscribe, go to
I just put a new (unused - not exactly new), Austron 1250A Crystal Frequency
Standard on eBay should anyone be interested.
-Doug Ronald
___
time-nuts mailing list -- time-nuts@febo.com
To unsubscribe, go to
Did the manual and schematics for the Austron 1250A get scanned to an
archive as suggested earlier?
If so can you please point me to it?
Alternatively can someone email me the pdf file(s)?
Many thanks
John GW3XPK johnrd...@googlemail.com
___
time-nuts
Hi gang,
I just put a scan of the Austron 1250A manual on
the www.to-way.com site. 1.3 MB .pdf 300x300 monochrome.
Had
___
time-nuts mailing list -- time-nuts@febo.com
To unsubscribe, go to
I have a manual for the Austron 1250A and have answered a couple of
questions as to the
schematics. I would like to loan my manual to some one that can scan it
and make it available on the NET
Anyone want that chore. I would want the manual returned after it was
scanned.
Bill K7NOM
Bill,
I would be happy to do it and add it to the to-way.com TF manual archive.
Had, K7MLR
At 02:25 PM 7/6/2008, you wrote:
I have a manual for the Austron 1250A and have answered a couple of
questions as to the
schematics. I would like to loan my manual to some one that can scan it
and
In a message dated 06/07/2008 22:26:29 GMT Daylight Time, [EMAIL PROTECTED]
writes:
I have a manual for the Austron 1250A and have answered a couple of
questions as to the
schematics. I would like to loan my manual to some one that can scan it
and make it available on the NET
Anyone want
[EMAIL PROTECTED] wrote:
In a message dated 06/07/2008 22:26:29 GMT Daylight Time, [EMAIL PROTECTED]
writes:
I have a manual for the Austron 1250A and have answered a couple of
questions as to the
schematics. I would like to loan my manual to some one that can scan it
and make it
In a message dated 07/07/2008 00:12:18 GMT Daylight Time, [EMAIL PROTECTED]
writes:
OK Forget my request as it is already in work.
Thanks Nigel I will refer any future requests to Didier's site
Bill K7NOM
--
Hi Bill
I'm having some fun uploading it right now but have just realised
19 matches
Mail list logo