On 07/06/2013 07:55 AM, Adrian wrote:
> Mark,
>
> I wouldn't replace a 20V cap with an only 10V rated one, especially when the
> nominal working voltage is alrady 10V. That would be a very bad idea.
> You can always use caps with higher voltage ratings as replacements which is
> good for reliabilit
Sent: Sunday, 7 July 2013 9:29 AM
To: time-nuts@febo.com
Subject: Re: [time-nuts] HP 5370B Leds pulsing slowly, buttons selecting
normally, PB LEDS scannning and appears to be reading o/k
Check with your power company. They may be able to switch taps on the
transformer to reduce the voltage. I
ainability.
marki
-Original Message-
From: time-nuts-boun...@febo.com [mailto:time-nuts-boun...@febo.com] On Behalf
Of Jim Lux
Sent: Sunday, 7 July 2013 8:01 AM
To: Discussion of precise time and frequency measurement
Subject: Re: [time-nuts] HP 5370B Leds pulsing slowly, buttons selecting
ssage-
From: time-nuts-boun...@febo.com [mailto:time-nuts-boun...@febo.com] On Behalf
Of Jim Lux
Sent: Sunday, 7 July 2013 8:01 AM
To: Discussion of precise time and frequency measurement
Subject: Re: [time-nuts] HP 5370B Leds pulsing slowly, buttons selecting
normally, PB LEDS scannnin
On 7/6/13 2:46 PM, Mark C. Stephens wrote:
Hopefully HP Voltage "Derated" the Cap as well so it can handle our
250V here.. We are across the road from the main transformer for the
area so the voltage is highest at our place, I checked the meter box
this morning - it is 255-258V on all 3 phases,
g problems.
-Original Message-
From: time-nuts-boun...@febo.com [mailto:time-nuts-boun...@febo.com] On Behalf
Of Orin Eman
Sent: Sunday, 7 July 2013 2:12 AM
To: Discussion of precise time and frequency measurement
Subject: Re: [time-nuts] HP 5370B Leds pulsing slowly, buttons selecting
normall
>
> -Original Message-
> From: time-nuts-boun...@febo.com [mailto:time-nuts-boun...@febo.com] On
> Behalf Of Mark C. Stephens
> Sent: Saturday, 6 July 2013 8:18 PM
> To: time-nuts@febo.com
> Subject: [time-nuts] HP 5370B Leds pulsing slowly, buttons selecting
> nor
You wouldn't even need a UPS, check Google for mains voltage conditioners.
APC's kit, for example, should be available worldwide and they make a
range that, here in the UK anyway, starts for under 50 GBP.
Regards
Nigel
GM8PZR
In a message dated 06/07/2013 13:26:06 GMT Daylight Time,
Running load might not be quite as bad as you'd expect, switching them all
on at exactly the same time would probably cause a nice fat pulse but
perhaps that's a bit extreme:-), allowing an adequate margin though is always
a
good idea.
If you could tap into the supply and get an idea of ru
is
Sent: Saturday, 6 July 2013 11:05 PM
To: Discussion of precise time and frequency measurement
Subject: Re: [time-nuts] HP 5370B Leds pulsing slowly, buttons selecting
normally, PB LEDS scannning and appears to be reading o/k
Mark C. Stephens wrote:
> Correct, C3 (17000uf @ 10v) is measuring
arki
-Original Message-
From: time-nuts-boun...@febo.com [mailto:time-nuts-boun...@febo.com] On Behalf
Of Adrian
Sent: Saturday, 6 July 2013 10:55 PM
To: Discussion of precise time and frequency measurement
Subject: Re: [time-nuts] HP 5370B Leds pulsing slowly, buttons selecting
norma
Mark C. Stephens wrote:
Correct, C3 (17000uf @ 10v) is measuring 39uf :)
I have a 29000@10V, same dimensions, do you think the rectifiers can hack that
big fella?
Without a blush!
Except for the 10V part. (Which I missed on the first post)
You have to use a capacitor that is at least 2x the
Mark C. Stephens wrote:
Correct, C3 (17000uf @ 10v) is measuring 39uf :)
I have a 29000@10V, same dimensions, do you think the rectifiers can hack that
big fella?
Without a blush!
-Chuck Harris
1uf is quite a bit more.
___
time-nuts mailing li
boun...@febo.com [mailto:time-nuts-boun...@febo.com] On Behalf
Of Mark C. Stephens
Sent: Saturday, 6 July 2013 8:18 PM
To: time-nuts@febo.com
Subject: [time-nuts] HP 5370B Leds pulsing slowly, buttons selecting normally,
PB LEDS scannning and appears to be reading o/k
I went to use my 5370B todayt
Message-
From: time-nuts-boun...@febo.com [mailto:time-nuts-boun...@febo.com] On Behalf
Of Adrian
Sent: Saturday, 6 July 2013 9:19 PM
To: Discussion of precise time and frequency measurement
Subject: Re: [time-nuts] HP 5370B Leds pulsing slowly, buttons selecting
normally, PB LEDS scannning and
there.
-marki
-Original Message-
From: time-nuts-boun...@febo.com [mailto:time-nuts-boun...@febo.com] On Behalf
Of gandal...@aol.com
Sent: Saturday, 6 July 2013 9:37 PM
To: time-nuts@febo.com
Subject: Re: [time-nuts] HP 5370B Leds pulsing slowly, buttons selecting
normally, PB ...
As per
ark C. Stephens
Sent: Saturday, 6 July 2013 8:18 PM
To: time-nuts@febo.com
Subject: [time-nuts] HP 5370B Leds pulsing slowly, buttons selecting
normally, PB LEDS scannning and appears to be reading o/k
I went to use my 5370B todayt and noticed the LEDS on the display are
slowly sort of pulsing b
...
-marki
-Original Message-
From: time-nuts-boun...@febo.com [mailto:time-nuts-boun...@febo.com] On Behalf
Of Mark C. Stephens
Sent: Saturday, 6 July 2013 8:18 PM
To: time-nuts@febo.com
Subject: [time-nuts] HP 5370B Leds pulsing slowly, buttons selecting normally,
PB LEDS scannning and
gt;
> -Original Message-
> From: time-nuts-boun...@febo.com [mailto:time-nuts-boun...@febo.com] On
> Behalf Of Mark C. Stephens
> Sent: Saturday, 6 July 2013 8:18 PM
> To: time-nuts@febo.com
> Subject: [time-nuts] HP 5370B Leds pulsing slowly, buttons selecting
> nor
C. Stephens
Sent: Saturday, 6 July 2013 8:18 PM
To: time-nuts@febo.com
Subject: [time-nuts] HP 5370B Leds pulsing slowly, buttons selecting normally,
PB LEDS scannning and appears to be reading o/k
I went to use my 5370B todayt and noticed the LEDS on the display are slowly
sort of pulsing
] HP 5370B Leds pulsing slowly, buttons selecting normally,
PB LEDS scannning and appears to be reading o/k
I went to use my 5370B todayt and noticed the LEDS on the display are slowly
sort of pulsing bright one after another.
Also all the push button LEDS are going on and off one by one.
The
I went to use my 5370B todayt and noticed the LEDS on the display are slowly
sort of pulsing bright one after another.
Also all the push button LEDS are going on and off one by one.
The strangest thing is that it appears to be working o/k via HPIB.
I don't have extender boards but I do have a sig
22 matches
Mail list logo