Re: [time-nuts] HP10514B Mixers

2010-03-31 Thread EWKehren
Is there a way you can post it on time-nuts? Thank you Bert Kehren In a message dated 3/30/2010 9:10:19 P.M. Eastern Daylight Time, kilodelta4foxm...@gmail.com writes: We'll the As are the package with the BNC connector. The Bs are for OEM equipment, they had 6 pins and a smaller

Re: [time-nuts] HP10514B Mixers

2010-03-31 Thread Brian Kirby
The manual is about a megabyte - the list will not accept it. ewkeh...@aol.com wrote: Is there a way you can post it on time-nuts? Thank you Bert Kehren In a message dated 3/30/2010 9:10:19 P.M. Eastern Daylight Time, kilodelta4foxm...@gmail.com writes: We'll the As are the package

Re: [time-nuts] HP10514B Mixers

2010-03-31 Thread EWKehren
Would you mind sending it direct to me at _ewkeh...@aol.com_ (mailto:ewkeh...@aol.com) as an attachment? You know we are in the test phase of a Dual Mixer and we are also running tests with the 10514 A and B along with the SYPD-1. The next board will accept the footprint of the 10514 B.

Re: [time-nuts] HP10514B Mixers

2010-03-31 Thread Bruce Griffiths
Upload it to the manuals section of Didier's site: http://www.ko4bb.com/cgi-bin/manuals.pl Bruce Brian Kirby wrote: The manual is about a megabyte - the list will not accept it. ewkeh...@aol.com wrote: Is there a way you can post it on time-nuts? Thank you Bert Kehren In a message dated

Re: [time-nuts] HP10514B Mixers

2010-03-31 Thread Brian Kirby
I uploaded the 10514 and 10534 mixer manuals to ko4bb site Bruce Griffiths wrote: Upload it to the manuals section of Didier's site: http://www.ko4bb.com/cgi-bin/manuals.pl Bruce ___ time-nuts mailing list -- time-nuts@febo.com To unsubscribe, go

[time-nuts] HP10514B Mixers

2010-03-30 Thread Mike Feher
I do not believe that I am familiar with the 10514B. I probably have about 6 or so 10514As with BNC connectors (most in a metal case and a few in epoxy), and, I recall from about 40 years ago a 10514A that was a small little black cube with leads for mounting on a PC board. Naturally, I had to

Re: [time-nuts] HP10514B Mixers

2010-03-30 Thread Brian Kirby
We'll the As are the package with the BNC connector. The Bs are for OEM equipment, they had 6 pins and a smaller plastic black case Turns out they have some of the lowest phase noise specs on record I can send the manual, if you like... Brian Mike Feher wrote: I do not believe

Re: [time-nuts] HP10514B Mixers

2010-03-30 Thread Mike Feher
...@febo.com] On Behalf Of Brian Kirby Sent: Tuesday, March 30, 2010 9:11 PM To: Discussion of precise time and frequency measurement Subject: Re: [time-nuts] HP10514B Mixers We'll the As are the package with the BNC connector. The Bs are for OEM equipment, they had 6 pins and a smaller plastic black

Re: [time-nuts] HP10514B Mixers

2010-03-30 Thread Bob Camp
Hi The obvious question is weather you need a real good mixer to make a low noise phase detector. Sorting the diodes as you did resulted in a mixer that performed at a specific level. Better matching would have made it have more isolation as a mixer, it might have helped the conversion loss

Re: [time-nuts] HP10514B Mixers

2010-03-30 Thread Mike Feher
: time-nuts-boun...@febo.com [mailto:time-nuts-boun...@febo.com] On Behalf Of Bob Camp Sent: Tuesday, March 30, 2010 9:25 PM To: Discussion of precise time and frequency measurement Subject: Re: [time-nuts] HP10514B Mixers Hi The obvious question is weather you need a real good mixer to make a low

Re: [time-nuts] HP10514B Mixers

2010-03-30 Thread Bob Camp
time and frequency measurement Subject: Re: [time-nuts] HP10514B Mixers Hi The obvious question is weather you need a real good mixer to make a low noise phase detector. Sorting the diodes as you did resulted in a mixer that performed at a specific level. Better matching would have