Re: [wsjt-devel] WSJT-X 2.3.0 sound card dongle issue

Yes, my computer has been rebooted several times. I am told that the "default device" soundcard was deleted despite that having been what I had been using.  I was told that too many people had not bothered to configure the sound so were transmitting too much garbage and so you (developers) remo

Re: [wsjt-devel] wsjtx v2.3-rc4

On 27/01/2021 20:46, Christoph Berg wrote: Re: jeff millar WSJTX starts, starts receiving, responds to Tune every thing is normal. But on Enable Tx and start of a Tx cycle, it keys, but no transmit tones. Tune works but Tx does not. the messages look right. There have been reports that using T

Re: [wsjt-devel] Heads up to Raspberry Pi users - was Re: WSJT-X 2.3.0 GA Release

Hi Bill, I did have to reboot after regenerating the locales. 73, -- Dave Slotter, W3DJS On Thu, Feb 4, 2021 at 5:55 PM Bill Somerville wrote: > Hi Dave, > > thanks for spotting that typo! > > I didn't have to reboot after using the locale-gen command, I didn't

Re: [wsjt-devel] Heads up to Raspberry Pi users - was Re: WSJT-X 2.3.0 GA Release

Hi Dave, thanks for spotting that typo! I didn't have to reboot after using the locale-gen command, I didn't try the GUI tool so not sure with that route. 73 Bill G4WJS. On 04/02/2021 22:44, Dave Slotter, W3DJS wrote: Note: The instruction of "sudo dpk-reconfigure locales" has a typo. It sh

Re: [wsjt-devel] Heads up to Raspberry Pi users - was Re: WSJT-X 2.3.0 GA Release

Note: The instruction of "sudo dpk-reconfigure locales" has a typo. It should be "sudo dpkg-reconfigure locales" (missing a "g") Also note that you may have to reboot after performing this operation. -- Dave Slotter, W3DJS On Mon, Feb 1, 2021 at 2:43 PM Bill Somer

[wsjt-devel] Release 2.4.0...

Hello, I would like to know if as happens normally,  2.4.0 will supersedes 2.3.0 in the future. Asking this because I never used the new modes (FST4 FST4W  and now Q65)  introduced recently in WSJT-X, nor I think to be going to use them at all. Of cour

Re: [wsjt-devel] WSJT-X 2.3.0 sound card dongle issue

I have had similar thing happen to me several times during new installs. I found that in WSJT-X if I clicked on the sound card choice, (which says “Blank” I think) it will show the correct sound card as a choice ….simply choose the correct sound card and all is back to normal. Ken K8HTL Sent

Re: [wsjt-devel] Bug report WSJT-X v2.4.0 rc1

On 04/02/2021 13:25, David Schmocker wrote: Good morning: Operating system:  Mac OS Mojave 10.14.6 Software version: WSJT-X v 2.4.0 rc1 Issue/behavior:  Program self closes (all windows) and     Unable to move outside of 15 second periods for this mode Steps re

Re: [wsjt-devel] WSJT-X 2.3.0 sound card dongle issue

On 03/02/2021 23:51, Jim Pruitt wrote: I was using WSJT-X 2.2.2 on my Windows 7 box but earlier today I got notice of release 2.3.0 and installed it. When I did the new version has no clue about my USB sound card dongle that I was using successfully with 2.2.2.  It shows the Audio input device

Re: [wsjt-devel] FST4 160M Dial Frequency

Please keep in mind that 1838.0 to 1838.2 is the low power WSPR spectrum. It should be protected from other signals and intermodulation, as well as suppressed SSB carriers, like they often can be found on 1840.0 (FT8 dial). I agree that the FST4 dial frequency could be a bit lower, but there sh

Re: [wsjt-devel] 2.4.0 RC1 - Decodes show no callsign

One feature in FT8 that I would love to see is a TX ratio setting similar to wspr or fst4w where 1/4 1/5 1/6 ratios can be selected allowing more cool down time with little loss in contacts made. I use those on 630m to good effect. On Thu, 4 Feb 2021, 7:52 pm Alan Groups, wrote: > Keeping therma

[wsjt-devel] 2.3.0 - Unexpected program exit in WSPR mode

Hi, I observed a number of unexpected program exits with release 2.3.0 in WSPR mode / band hopping mode. The exit is reproducible, the timing of when it happens however, is not. The radio setting is : Hamlib NET rigctl, connected to a network server (SparkSDR), PTT : CAT, Transmit Audio source :

Re: [wsjt-devel] 2.4.0 RC1 - Decodes show no callsign

Keeping thermal stress on the system - rig and PSU - by turning power down at least a bit from full output makes sense to me with these modes, whether or not rig ratings demand it, particularly as any reduction in received signal strength will be minor. More heat = more risk of failure regardl

Re: [wsjt-devel] 2.4.0 RC1 - Decodes show no callsign

Hi! If your rig has FM and has full output power there without warnings of FM TX period lengths the PA should handle it. FM, or CW carrier on, are most closest to continuous tone modulated SSB. As Reino says AM must have smaller carrier for modulation reasons. Reino Talarmo kirjoitti 3.2.2021