Hello,
I have just installed Seawolf on a VERY powerful Intel Xeon based
machine, and I am having a couple of problems. I've searched the
archives, and while I can find a few similar issues, nothing quite
fits. First, the machine:
SuperMicro S2QR6 Motherboard
4 Pentium III Xeon 700 Mhz CPUs
8 GB of RAM (16 512 MB registered ECC PC 100 DIMMs by Viking)
ATI Xpert 128 Video card ( 16 MB of RAM, PCI)
2 Ultra 160 SCSI Seagate Drives (36 GB a piece, 80 pin SCA interface.
They plug into the built in Adaptec 7899 controller on the motherboard)
Various other components (Asus CD ROM, Yamaha Burner, floppy, etc.)
Now the problems:
1) X refuses to work. The X based graphical installer works fine, other
than the fact that is cannot test the X configuration you setup for
after the install. Attempts to use Xconfigurator result in it
generating a complete XF86Config file, but upon trying to test it
bringing up a message that "There is an Error in you XF86Config file"
and offering you a choice to go back and try again (never works) or
exit. startx looks like it working but fails after a few seconds. I
have attached my log file from a "startx", but I think the critical
lines are:
(II) Primary Device is: PCI 01:04:0
(--) Assigning Device section with no busID to primary device
(EE) No devices detected
X doesn't seem to be finding the card. My best bet is that there is
some kind of IRQ conflict, but video cards don't seem to be listed in
/proc/interrupts (at least not on any of my machines), so I can't tell.
The card is autodetected by both anaconda and Xconfigurator. Any help
would be greatly appreciated
2) Everything is very slow. The thing takes between 3 and five second
to start each service on boot. The kernel startup goes quite quickly,
but services are deadly slow. My Pentium 133 with 32 megs of RAM boots
quicker. Commands take several seconds to execute. I was going to
compile a new kernel for it to see if I could improve performance (and
maybe fix X), but it has been working for most of an hour on the
compile, my PII 400 is faster on a kernel compile. I suspect the new
kernel (or at least recompiled kernel) is the only way to fix this
problem, but if anyone can offer a suggestion to speed it up BEFORE I
compile, I'd appreciate it (because looking back, I think I messed up
the SCSI config on this one, so I shall have to do it again). I am
attaching the results of a dmesg command as "bootlog".
Thanks in advance for any help anyone can give. This is by far the most
trouble I've had with an install in years. I assume that the high end
hardware is causing problems, but I'd really like to fix them.
--
Thank you,
Trevor Antczak
Network Administrator II
Tulane University Math Dept.
[EMAIL PROTECTED]
(504) 862-3457
XFree86 Version 4.0.3 / X Window System
(protocol Version 11, revision 0, vendor release 6400)
Release Date: 16 March 2001
If the server is older than 6-12 months, or if your card is
newer than the above date, look for a newer version before
reporting problems. (See http://www.XFree86.Org/FAQ)
Operating System: Linux 2.2.17-8smp i686 [ELF]
Module Loader present
(==) Log file: "/var/log/XFree86.0.log", Time: Tue Aug 7 13:14:09 2001
(==) Using config file: "/etc/X11/XF86Config-4"
Markers: (--) probed, (**) from config file, (==) default setting,
(++) from command line, (!!) notice, (II) informational,
(WW) warning, (EE) error, (??) unknown.
(==) ServerLayout "XFree86 Configured"
(**) |-->Screen "Screen0" (0)
(**) | |-->Monitor "CPD-E500"
(**) | |-->Device "ATI Rage 128"
(**) |-->Input Device "Mouse0"
(**) |-->Input Device "Keyboard0"
(**) Option "XkbLayout" "us"
(**) XKB: layout: "us"
(**) FontPath set to "unix/:7100"
(==) RgbPath set to "/usr/X11R6/lib/X11/rgb"
(==) ModulePath set to "/usr/X11R6/lib/modules"
(--) using VT number 7
(WW) Cannot open APM
(II) Module ABI versions:
XFree86 ANSI C Emulation: 0.1
XFree86 Video Driver: 0.3
XFree86 XInput driver : 0.1
XFree86 Server Extension : 0.1
XFree86 Font Renderer : 0.2
(II) Loader running on linux
(II) LoadModule: "bitmap"
(II) Loading /usr/X11R6/lib/modules/fonts/libbitmap.a
(II) Module bitmap: vendor="The XFree86 Project"
compiled for 4.0.3, module version = 1.0.0
Module class: XFree86 Font Renderer
ABI class: XFree86 Font Renderer, version 0.2
(II) Loading font Bitmap
(II) LoadModule: "pcidata"
(II) Loading /usr/X11R6/lib/modules/libpcidata.a
(II) Module pcidata: vendor="The XFree86 Project"
compiled for 4.0.3, module version = 0.1.0
ABI class: XFree86 Video Driver, version 0.3
(II) PCI: Probing config type using method 1
(II) PCI: Config type is 1
(II) PCI: stages = 0x03, oldVal1 = 0x800018e0, mode1Res1 = 0x80000000
(II) PCI: PCI scan (all values are in hex)
(II) PCI: 00:00:0: chip 1166,0008 card 0000,0000 rev 21 class 06,00,00 hdr 80
(II) PCI: 00:00:1: chip 1166,0008 card 0000,0000 rev 01 class 06,00,00 hdr 80
(II) PCI: 00:00:2: chip 1166,0006 card 0000,0000 rev 00 class 06,00,00 hdr 80
(II) PCI: 00:00:3: chip 1166,0006 card 0000,0000 rev 00 class 06,00,00 hdr 80
(II) PCI: 00:01:0: chip 1102,0002 card 1102,8027 rev 08 class 04,01,00 hdr 80
(II) PCI: 00:01:1: chip 1102,7002 card 1102,0020 rev 08 class 09,80,00 hdr 80
(II) PCI: 00:03:0: chip 8086,1229 card 8086,100c rev 08 class 02,00,00 hdr 00
(II) PCI: 00:0f:0: chip 1166,0200 card 1166,0200 rev 51 class 06,01,00 hdr 80
(II) PCI: 00:0f:1: chip 1166,0211 card 0000,0000 rev 00 class 01,01,8a hdr 80
(II) PCI: 00:0f:2: chip 1166,0220 card 1166,0220 rev 04 class 0c,03,10 hdr 80
(II) PCI: 01:04:0: chip 1002,5050 card 1002,0008 rev 00 class 03,00,00 hdr 00
(II) PCI: 01:05:0: chip 9005,00cf card 9d15,0001 rev 01 class 01,00,00 hdr 80
(II) PCI: 01:05:1: chip 9005,00cf card 9d15,0001 rev 01 class 01,00,00 hdr 80
(II) PCI: End of PCI scan
(II) LoadModule: "scanpci"
(II) Loading /usr/X11R6/lib/modules/libscanpci.a
(II) Module scanpci: vendor="The XFree86 Project"
compiled for 4.0.3, module version = 0.1.0
ABI class: XFree86 Video Driver, version 0.3
(II) UnloadModule: "scanpci"
(II) Unloading /usr/X11R6/lib/modules/libscanpci.a
(II) Host-to-PCI bridge:
(II) Host-to-PCI bridge:
(II) Host-to-PCI bridge:
(II) Host-to-PCI bridge:
(II) PCI-to-ISA bridge:
(II) Bus 0: bridge is at (0:0:0), (-1,0,0), BCTRL: 0x00 (VGA_EN is cleared)
(II) Bus 0 I/O range:
[0] -1 0x00000000 - 0x0000ffff (0x10000) IX[B]
(II) Bus 0 non-prefetchable memory range:
[0] -1 0x00000000 - 0xffffffff (0x0) MX[B]
(II) Bus 0 prefetchable memory range:
[0] -1 0x00000000 - 0xffffffff (0x0) MX[B]
(II) Bus 1: bridge is at (0:0:0), (-1,1,0), BCTRL: 0x00 (VGA_EN is cleared)
(II) Bus 1 I/O range:
[0] -1 0x00000000 - 0x0000ffff (0x10000) IX[B]
(II) Bus 1 non-prefetchable memory range:
[0] -1 0x00000000 - 0xffffffff (0x0) MX[B]
(II) Bus 1 prefetchable memory range:
[0] -1 0x00000000 - 0xffffffff (0x0) MX[B]
(II) Bus -1: bridge is at (0:0:0), (-1,-1,0), BCTRL: 0x00 (VGA_EN is cleared)
(II) Bus -1 I/O range:
[0] -1 0x00000000 - 0x0000ffff (0x10000) IX[B]
(II) Bus -1 non-prefetchable memory range:
[0] -1 0x00000000 - 0xffffffff (0x0) MX[B]
(II) Bus -1 prefetchable memory range:
[0] -1 0x00000000 - 0xffffffff (0x0) MX[B]
(II) Bus -1: bridge is at (0:0:0), (-1,-1,0), BCTRL: 0x00 (VGA_EN is cleared)
(II) Bus -1 I/O range:
[0] -1 0x00000000 - 0x0000ffff (0x10000) IX[B]
(II) Bus -1 non-prefetchable memory range:
[0] -1 0x00000000 - 0xffffffff (0x0) MX[B]
(II) Bus -1 prefetchable memory range:
[0] -1 0x00000000 - 0xffffffff (0x0) MX[B]
(II) Bus -1: bridge is at (0:15:0), (0,-1,0), BCTRL: 0x00 (VGA_EN is cleared)
(II) Bus -1 I/O range:
(II) Bus -1 non-prefetchable memory range:
(II) Bus -1 prefetchable memory range:
(--) PCI:*(1:4:0) ATI unknown chipset (0x5050) rev 0, Mem @ 0xf8000000/26,
0xfeafc000/14, I/O @ 0xd800/8
(II) Addressable bus resource ranges are
[0] -1 0x00000000 - 0xffffffff (0x0) MX[B]
[1] -1 0x00000000 - 0x0000ffff (0x10000) IX[B]
(II) OS-reported resource ranges:
[0] -1 0xffe00000 - 0xffffffff (0x200000) MX[B](B)
[1] -1 0x00100000 - 0x3fffffff (0x3ff00000) MX[B]E(B)
[2] -1 0x000f0000 - 0x000fffff (0x10000) MX[B]
[3] -1 0x000c0000 - 0x000effff (0x30000) MX[B]
[4] -1 0x00000000 - 0x0009ffff (0xa0000) MX[B]
[5] -1 0x00000000 - 0x000001ff (0x200) IX[B]E
(II) Active PCI resource ranges:
[0] -1 0xfeaa0000 - 0xfeabffff (0x20000) MX[B]
[1] -1 0xfea80000 - 0xfea9ffff (0x20000) MX[B]
[2] -1 0xfe9ff000 - 0xfe9fffff (0x1000) MX[B]
[3] -1 0xfe800000 - 0xfe8fffff (0x100000) MX[B]
[4] -1 0xfe9fe000 - 0xfe9fefff (0x1000) MX[B]
[5] -1 0xfeac0000 - 0xfeadffff (0x20000) MX[B](B)
[6] -1 0xfeafc000 - 0xfeafffff (0x4000) MX[B](B)
[7] -1 0xf8000000 - 0xfbffffff (0x4000000) MX[B](B)
[8] -1 0x0000d400 - 0x0000d4ff (0x100) IX[B]
[9] -1 0x0000d000 - 0x0000d0ff (0x100) IX[B]
[10] -1 0x0000ffa0 - 0x0000ffaf (0x10) IX[B]
[11] -1 0x0000c800 - 0x0000c83f (0x40) IX[B]
[12] -1 0x0000cff0 - 0x0000cff7 (0x8) IX[B]
[13] -1 0x0000cf80 - 0x0000cf9f (0x20) IX[B]
[14] -1 0x0000d800 - 0x0000d8ff (0x100) IX[B](B)
(II) Active PCI resource ranges after removing overlaps:
[0] -1 0xfeaa0000 - 0xfeabffff (0x20000) MX[B]
[1] -1 0xfea80000 - 0xfea9ffff (0x20000) MX[B]
[2] -1 0xfe9ff000 - 0xfe9fffff (0x1000) MX[B]
[3] -1 0xfe800000 - 0xfe8fffff (0x100000) MX[B]
[4] -1 0xfe9fe000 - 0xfe9fefff (0x1000) MX[B]
[5] -1 0xfeac0000 - 0xfeadffff (0x20000) MX[B](B)
[6] -1 0xfeafc000 - 0xfeafffff (0x4000) MX[B](B)
[7] -1 0xf8000000 - 0xfbffffff (0x4000000) MX[B](B)
[8] -1 0x0000d400 - 0x0000d4ff (0x100) IX[B]
[9] -1 0x0000d000 - 0x0000d0ff (0x100) IX[B]
[10] -1 0x0000ffa0 - 0x0000ffaf (0x10) IX[B]
[11] -1 0x0000c800 - 0x0000c83f (0x40) IX[B]
[12] -1 0x0000cff0 - 0x0000cff7 (0x8) IX[B]
[13] -1 0x0000cf80 - 0x0000cf9f (0x20) IX[B]
[14] -1 0x0000d800 - 0x0000d8ff (0x100) IX[B](B)
(II) OS-reported resource ranges after removing overlaps with PCI:
[0] -1 0xffe00000 - 0xffffffff (0x200000) MX[B](B)
[1] -1 0x00100000 - 0x3fffffff (0x3ff00000) MX[B]E(B)
[2] -1 0x000f0000 - 0x000fffff (0x10000) MX[B]
[3] -1 0x000c0000 - 0x000effff (0x30000) MX[B]
[4] -1 0x00000000 - 0x0009ffff (0xa0000) MX[B]
[5] -1 0x00000000 - 0x000001ff (0x200) IX[B]E
(II) All system resource ranges:
[0] -1 0xffe00000 - 0xffffffff (0x200000) MX[B](B)
[1] -1 0x00100000 - 0x3fffffff (0x3ff00000) MX[B]E(B)
[2] -1 0x000f0000 - 0x000fffff (0x10000) MX[B]
[3] -1 0x000c0000 - 0x000effff (0x30000) MX[B]
[4] -1 0x00000000 - 0x0009ffff (0xa0000) MX[B]
[5] -1 0xfeaa0000 - 0xfeabffff (0x20000) MX[B]
[6] -1 0xfea80000 - 0xfea9ffff (0x20000) MX[B]
[7] -1 0xfe9ff000 - 0xfe9fffff (0x1000) MX[B]
[8] -1 0xfe800000 - 0xfe8fffff (0x100000) MX[B]
[9] -1 0xfe9fe000 - 0xfe9fefff (0x1000) MX[B]
[10] -1 0xfeac0000 - 0xfeadffff (0x20000) MX[B](B)
[11] -1 0xfeafc000 - 0xfeafffff (0x4000) MX[B](B)
[12] -1 0xf8000000 - 0xfbffffff (0x4000000) MX[B](B)
[13] -1 0x00000000 - 0x000001ff (0x200) IX[B]E
[14] -1 0x0000d400 - 0x0000d4ff (0x100) IX[B]
[15] -1 0x0000d000 - 0x0000d0ff (0x100) IX[B]
[16] -1 0x0000ffa0 - 0x0000ffaf (0x10) IX[B]
[17] -1 0x0000c800 - 0x0000c83f (0x40) IX[B]
[18] -1 0x0000cff0 - 0x0000cff7 (0x8) IX[B]
[19] -1 0x0000cf80 - 0x0000cf9f (0x20) IX[B]
[20] -1 0x0000d800 - 0x0000d8ff (0x100) IX[B](B)
(II) LoadModule: "dbe"
(II) Loading /usr/X11R6/lib/modules/extensions/libdbe.a
(II) Module dbe: vendor="The XFree86 Project"
compiled for 4.0.3, module version = 1.0.0
Module class: XFree86 Server Extension
ABI class: XFree86 Server Extension, version 0.1
(II) Loading extension DOUBLE-BUFFER
(II) LoadModule: "GLcore"
(II) Loading /usr/X11R6/lib/modules/extensions/libGLcore.a
(II) Module GLcore: vendor="The XFree86 Project"
compiled for 4.0.3, module version = 1.0.0
ABI class: XFree86 Server Extension, version 0.1
(II) LoadModule: "dri"
(II) Loading /usr/X11R6/lib/modules/extensions/libdri.a
(II) Module dri: vendor="The XFree86 Project"
compiled for 4.0.3, module version = 1.0.0
ABI class: XFree86 Server Extension, version 0.1
(II) Loading extension XFree86-DRI
(II) Loading sub module "drm"
(II) LoadModule: "drm"
(II) Loading /usr/X11R6/lib/modules/linux/libdrm.a
(II) Module drm: vendor="The XFree86 Project"
compiled for 4.0.3, module version = 1.0.0
ABI class: XFree86 Server Extension, version 0.1
(II) LoadModule: "glx"
(II) Loading /usr/X11R6/lib/modules/extensions/libglx.a
(II) Module glx: vendor="The XFree86 Project"
compiled for 4.0.3, module version = 1.0.0
ABI class: XFree86 Server Extension, version 0.1
(II) Loading extension GLX
(II) Loading sub module "GLcore"
(II) LoadModule: "GLcore"
(II) Reloading /usr/X11R6/lib/modules/extensions/libGLcore.a
(II) LoadModule: "extmod"
(II) Loading /usr/X11R6/lib/modules/extensions/libextmod.a
(II) Module extmod: vendor="The XFree86 Project"
compiled for 4.0.3, module version = 1.0.0
Module class: XFree86 Server Extension
ABI class: XFree86 Server Extension, version 0.1
(II) Loading extension SHAPE
(II) Loading extension MIT-SUNDRY-NONSTANDARD
(II) Loading extension BIG-REQUESTS
(II) Loading extension SYNC
(II) Loading extension MIT-SCREEN-SAVER
(II) Loading extension XC-MISC
(II) Loading extension XFree86-VidModeExtension
(II) Loading extension XFree86-Misc
(II) Loading extension XFree86-DGA
(II) Loading extension DPMS
(II) Loading extension FontCache
(II) Loading extension TOG-CUP
(II) Loading extension Extended-Visual-Information
(II) Loading extension XVideo
(II) LoadModule: "v4l"
(II) Loading /usr/X11R6/lib/modules/drivers/linux/v4l_drv.o
(II) Module v4l: vendor="The XFree86 Project"
compiled for 4.0.3, module version = 0.0.1
ABI class: XFree86 Video Driver, version 0.3
(II) LoadModule: "r128"
(II) Loading /usr/X11R6/lib/modules/drivers/r128_drv.o
(II) Module r128: vendor="The XFree86 Project"
compiled for 4.0.3, module version = 4.0.1
Module class: XFree86 Video Driver
ABI class: XFree86 Video Driver, version 0.3
(II) LoadModule: "ati"
(II) Loading /usr/X11R6/lib/modules/drivers/ati_drv.o
(II) Module ati: vendor="The XFree86 Project"
compiled for 4.0.3, module version = 6.2.3
Module class: XFree86 Video Driver
ABI class: XFree86 Video Driver, version 0.3
(II) LoadModule: "mouse"
(II) Loading /usr/X11R6/lib/modules/input/mouse_drv.o
(II) Module mouse: vendor="The XFree86 Project"
compiled for 4.0.3, module version = 1.0.0
Module class: XFree86 XInput Driver
ABI class: XFree86 XInput driver, version 0.1
(II) v4l driver for Video4Linux
(II) ATI: ATI driver (version 6.2.3) for chipsets: ati, ativga
(II) R128: Driver for ATI Rage 128 chipsets: ATI Rage 128 RE (PCI),
ATI Rage 128 RF (AGP), ATI Rage 128 RG (AGP), ATI Rage 128 RK (PCI),
ATI Rage 128 RL (AGP), ATI Rage 128 Pro PD (AGP),
ATI Rage 128 Pro PF (AGP), ATI Rage 128 Mobility LE (PCI),
ATI Rage 128 Mobility LF (AGP), ATI Rage 128 Mobility MF (AGP),
ATI Rage 128 Mobility ML (AGP)
(II) RADEON: Driver for ATI Radeon chipsets: ATI Radeon QD (AGP),
ATI Radeon QE (AGP), ATI Radeon QF (AGP), ATI Radeon QG (AGP)
(II) Primary Device is: PCI 01:04:0
(--) Assigning device section with no busID to primary device
(EE) No devices detected.
Fatal server error:
no screens found
When reporting a problem related to a server crash, please send
the full server output, not just the last messages.
This can be found in the log file "/var/log/XFree86.0.log".
Please report problems to [EMAIL PROTECTED]
APIC ID 4, APIC INT 02
Int: type 0, pol 1, trig 1, bus 3, IRQ 03, APIC ID 4, APIC INT 03
Int: type 0, pol 1, trig 1, bus 3, IRQ 04, APIC ID 4, APIC INT 04
Int: type 0, pol 1, trig 1, bus 3, IRQ 06, APIC ID 4, APIC INT 06
Int: type 0, pol 1, trig 1, bus 3, IRQ 07, APIC ID 4, APIC INT 07
Int: type 0, pol 1, trig 1, bus 3, IRQ 08, APIC ID 4, APIC INT 08
Int: type 0, pol 1, trig 1, bus 3, IRQ 0c, APIC ID 4, APIC INT 0c
Int: type 0, pol 1, trig 1, bus 3, IRQ 0d, APIC ID 4, APIC INT 0d
Int: type 0, pol 1, trig 1, bus 3, IRQ 0e, APIC ID 4, APIC INT 0e
Int: type 0, pol 1, trig 1, bus 3, IRQ 0f, APIC ID 4, APIC INT 0f
Lint: type 3, pol 1, trig 1, bus 3, IRQ 00, APIC ID ff, APIC LINT 00
Lint: type 1, pol 1, trig 1, bus 0, IRQ 00, APIC ID ff, APIC LINT 01
Processors: 4
mapped APIC to ffffe000 (fee00000)
mapped IOAPIC to ffffd000 (fec00000)
mapped IOAPIC to ffffc000 (fec01000)
hm, page 01000000 reserved twice.
Kernel command line: auto BOOT_IMAGE=linux ro root=801
BOOT_FILE=/boot/vmlinuz-2.4.2-2enterprise
Initializing CPU#0
Detected 701.623 MHz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 1399.19 BogoMIPS
Memory: 8085212k/8388608k available (1513k kernel code, 143200k reserved, 103k data,
252k init, 7311296k highmem)
Dentry-cache hash table entries: 524288 (order: 10, 4194304 bytes)
Buffer-cache hash table entries: 524288 (order: 9, 2097152 bytes)
Page-cache hash table entries: 524288 (order: 10, 4194304 bytes)
Inode-cache hash table entries: 524288 (order: 10, 4194304 bytes)
VFS: Diskquotas version dquot_6.5.0 initialized
CPU: Before vendor init, caps: 0383fbff 00000000 00000000, vendor = 0
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 1024K
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: After vendor init, caps: 0383fbff 00000000 00000000 00000000
CPU: After generic, caps: 0383fbff 00000000 00000000 00000000
CPU: Common caps: 0383fbff 00000000 00000000 00000000
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
mtrr: v1.37 (20001109) Richard Gooch ([EMAIL PROTECTED])
mtrr: detected mtrr type: Intel
CPU: Before vendor init, caps: 0383fbff 00000000 00000000, vendor = 0
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 1024K
Intel machine check reporting enabled on CPU#0.
CPU: After vendor init, caps: 0383fbff 00000000 00000000 00000000
CPU: After generic, caps: 0383fbff 00000000 00000000 00000000
CPU: Common caps: 0383fbff 00000000 00000000 00000000
CPU0: Intel Pentium III (Cascades) stepping 01
per-CPU timeslice cutoff: 2927.55 usecs.
Getting VERSION: 40011
Getting VERSION: 40011
Getting ID: 0
Getting ID: f000000
Getting LVT0: 700
Getting LVT1: 400
enabled ExtINT on CPU#0
ESR value before enabling vector: 00000004
ESR value after enabling vector: 00000000
CPU present map: f
Booting processor 1/1 eip 3000
Setting warm reset code and vector.
1.
2.
3.
Asserting INIT.
Waiting for send to finish...
+Deasserting INIT.
Waiting for send to finish...
+#startup loops: 2.
Sending STARTUP #1.
After apic_write.
Initializing CPU#1
CPU#1 (phys ID: 1) waiting for CALLOUT
Startup point 1.
Waiting for send to finish...
+Sending STARTUP #2.
After apic_write.
Startup point 1.
Waiting for send to finish...
+After Startup.
Before Callout 1.
After Callout 1.
CALLIN, before setup_local_APIC().
masked ExtINT on CPU#1
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
Calibrating delay loop... 1402.47 BogoMIPS
Stack at about c990dfb8
CPU: Before vendor init, caps: 0383fbff 00000000 00000000, vendor = 0
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 1024K
Intel machine check reporting enabled on CPU#1.
CPU: After vendor init, caps: 0383fbff 00000000 00000000 00000000
CPU: After generic, caps: 0383fbff 00000000 00000000 00000000
CPU: Common caps: 0383fbff 00000000 00000000 00000000
OK.
CPU1: Intel Pentium III (Cascades) stepping 01
CPU has booted.
Booting processor 2/2 eip 3000
Setting warm reset code and vector.
1.
2.
3.
Asserting INIT.
Waiting for send to finish...
+Deasserting INIT.
Waiting for send to finish...
+#startup loops: 2.
Sending STARTUP #1.
After apic_write.
Initializing CPU#2
CPU#2 (phys ID: 2) waiting for CALLOUT
Startup point 1.
Waiting for send to finish...
+Sending STARTUP #2.
After apic_write.
Startup point 1.
Waiting for send to finish...
+After Startup.
Before Callout 2.
After Callout 2.
CALLIN, before setup_local_APIC().
masked ExtINT on CPU#2
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
Calibrating delay loop... 1402.47 BogoMIPS
Stack at about c991ffb8
CPU: Before vendor init, caps: 0383fbff 00000000 00000000, vendor = 0
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 1024K
Intel machine check reporting enabled on CPU#2.
CPU: After vendor init, caps: 0383fbff 00000000 00000000 00000000
CPU: After generic, caps: 0383fbff 00000000 00000000 00000000
CPU: Common caps: 0383fbff 00000000 00000000 00000000
OK.
CPU2: Intel Pentium III (Cascades) stepping 01
CPU has booted.
Booting processor 3/3 eip 3000
Setting warm reset code and vector.
1.
2.
3.
Asserting INIT.
Waiting for send to finish...
+Deasserting INIT.
Waiting for send to finish...
+#startup loops: 2.
Sending STARTUP #1.
After apic_write.
Initializing CPU#3
CPU#3 (phys ID: 3) waiting for CALLOUT
Startup point 1.
Waiting for send to finish...
+Sending STARTUP #2.
After apic_write.
Startup point 1.
Waiting for send to finish...
+After Startup.
Before Callout 3.
After Callout 3.
CALLIN, before setup_local_APIC().
masked ExtINT on CPU#3
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
Calibrating delay loop... 1402.47 BogoMIPS
Stack at about c991dfb8
CPU: Before vendor init, caps: 0383fbff 00000000 00000000, vendor = 0
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 1024K
Intel machine check reporting enabled on CPU#3.
CPU: After vendor init, caps: 0383fbff 00000000 00000000 00000000
CPU: After generic, caps: 0383fbff 00000000 00000000 00000000
CPU: Common caps: 0383fbff 00000000 00000000 00000000
OK.
CPU3: Intel Pentium III (Cascades) stepping 01
CPU has booted.
Before bogomips.
Total of 4 processors activated (5606.60 BogoMIPS).
Before bogocount - setting activated=1.
Boot done.
ENABLING IO-APIC IRQs
...changing IO-APIC physical APIC ID to 4 ... ok.
...changing IO-APIC physical APIC ID to 5 ... ok.
Synchronizing Arb IDs.
init IO_APIC IRQs
IO-APIC (apicid-pin) 4-0, 4-5, 4-9, 4-11, 5-2, 5-3, 5-4, 5-5, 5-6, 5-7, 5-8, 5-9,
5-11, 5-13, 5-14 not connected.
..TIMER: vector=49 pin1=2 pin2=0
..MP-BIOS bug: 8254 timer not connected to IO-APIC
...trying to set up timer (IRQ0) through the 8259A ...
..... (found pin 0) ...works.
number of MP IRQ sources: 18.
number of IO-APIC #4 registers: 16.
number of IO-APIC #5 registers: 16.
testing the IO APIC.......................
IO APIC #4......
.... register #00: 04000000
....... : physical APIC id: 04
.... register #01: 000F0011
....... : max redirection entries: 000F
....... : IO APIC version: 0011
.... register #02: 00000000
....... : arbitration: 00
.... IRQ redirection table:
NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:
00 00F 0F 0 0 0 0 0 1 1 31
01 00F 0F 0 0 0 0 0 1 1 39
02 000 00 1 0 0 0 0 0 0 00
03 00F 0F 0 0 0 0 0 1 1 41
04 00F 0F 0 0 0 0 0 1 1 49
05 000 00 1 0 0 0 0 0 0 00
06 00F 0F 0 0 0 0 0 1 1 51
07 00F 0F 0 0 0 0 0 1 1 59
08 00F 0F 0 0 0 0 0 1 1 61
09 000 00 1 0 0 0 0 0 0 00
0a 00F 0F 1 1 0 1 0 1 1 69
0b 000 00 1 0 0 0 0 0 0 00
0c 00F 0F 0 0 0 0 0 1 1 71
0d 00F 0F 0 0 0 0 0 1 1 79
0e 00F 0F 0 0 0 0 0 1 1 81
0f 00F 0F 0 0 0 0 0 1 1 89
IO APIC #5......
.... register #00: 05000000
....... : physical APIC id: 05
.... register #01: 000F0011
....... : max redirection entries: 000F
....... : IO APIC version: 0011
.... register #02: 01000000
....... : arbitration: 01
.... IRQ redirection table:
NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:
00 00F 0F 1 1 0 1 0 1 1 91
01 00F 0F 1 1 0 1 0 1 1 99
02 000 00 1 0 0 0 0 0 0 00
03 000 00 1 0 0 0 0 0 0 00
04 000 00 1 0 0 0 0 0 0 00
05 000 00 1 0 0 0 0 0 0 00
06 000 00 1 0 0 0 0 0 0 00
07 000 00 1 0 0 0 0 0 0 00
08 000 00 1 0 0 0 0 0 0 00
09 000 00 1 0 0 0 0 0 0 00
0a 00F 0F 1 1 0 1 0 1 1 A1
0b 000 00 1 0 0 0 0 0 0 00
0c 00F 0F 1 1 0 1 0 1 1 A9
0d 000 00 1 0 0 0 0 0 0 00
0e 000 00 1 0 0 0 0 0 0 00
0f 00F 0F 1 1 0 1 0 1 1 B1
IRQ to pin mappings:
IRQ0 -> 0:2
IRQ1 -> 0:1
IRQ3 -> 0:3
IRQ4 -> 0:4
IRQ6 -> 0:6
IRQ7 -> 0:7
IRQ8 -> 0:8
IRQ10 -> 0:10
IRQ12 -> 0:12
IRQ13 -> 0:13
IRQ14 -> 0:14
IRQ15 -> 0:15
IRQ16 -> 1:0
IRQ17 -> 1:1
IRQ26 -> 1:10
IRQ28 -> 1:12
IRQ31 -> 1:15
.................................... done.
calibrating APIC timer ...
..... CPU clock speed is 701.6032 MHz.
..... host bus clock speed is 100.2288 MHz.
cpu: 0, clocks: 1002288, slice: 200457
CPU0<T0:1002288,T1:801824,D:7,S:200457,C:1002288>
cpu: 1, clocks: 1002288, slice: 200457
cpu: 3, clocks: 1002288, slice: 200457
cpu: 2, clocks: 1002288, slice: 200457
CPU1<T0:1002288,T1:601360,D:14,S:200457,C:1002288>
CPU2<T0:1002288,T1:400912,D:5,S:200457,C:1002288>
CPU3<T0:1002288,T1:200448,D:12,S:200457,C:1002288>
checking TSC synchronization across CPUs: passed.
Setting commenced=1, go go go
PCI: PCI BIOS revision 2.10 entry at 0xfdbb1, last bus=2
PCI: Using configuration type 1
PCI: Probing PCI hardware
PCI: Discovered peer bus 01
PCI->APIC IRQ transform: (B0,I1,P0) -> 26
PCI->APIC IRQ transform: (B0,I3,P0) -> 31
PCI->APIC IRQ transform: (B0,I15,P0) -> 10
PCI->APIC IRQ transform: (B1,I4,P0) -> 28
PCI->APIC IRQ transform: (B1,I5,P0) -> 16
PCI->APIC IRQ transform: (B1,I5,P1) -> 17
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.14)
apm: disabled - APM is not SMP safe.
Starting kswapd v1.8
pty: 256 Unix98 ptys configured
block: queued sectors max/low 5380368kB/5249296kB, 8192 slots per queue
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
Uniform Multi-Platform E-IDE driver Revision: 6.31
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ServerWorks OSB4: IDE controller on PCI bus 00 dev 79
ServerWorks OSB4: chipset revision 0
ServerWorks OSB4: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xffa0-0xffa7, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xffa8-0xffaf, BIOS settings: hdc:pio, hdd:pio
hda: ASUS CD-S500/A, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Floppy drive(s): fd0 is 1.44M
FDC 0 is a National Semiconductor PC87306
RAMDISK: Compressed image found at block 0
Freeing initrd memory: 361k freed
Serial driver version 5.02 (2000-08-09) with MANY_PORTS MULTIPORT SHARE_IRQ SERIAL_PCI
ISAPNP enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
ttyS01 at 0x02f8 (irq = 3) is a 16550A
Real Time Clock Driver v1.10d
md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
md.c: sizeof(mdp_super_t) = 4096
autodetecting RAID arrays
autorun ...
... autorun DONE.
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 65536 buckets, 512Kbytes
TCP: Hash tables configured (established 524288 bind 65536)
Linux IP multicast router 0.06 plus PIM-SM
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
VFS: Mounted root (ext2 filesystem).
SCSI subsystem driver Revision: 1.00
(scsi0) <Adaptec AIC-7899 Ultra 160/m SCSI host adapter> found at PCI 1/5/0
(scsi0) Wide Channel A, SCSI ID=7, 32/255 SCBs
(scsi0) Downloading sequencer code... 396 instructions downloaded
(scsi1) <Adaptec AIC-7899 Ultra 160/m SCSI host adapter> found at PCI 1/5/1
(scsi1) Wide Channel B, SCSI ID=7, 32/255 SCBs
(scsi1) Downloading sequencer code... 396 instructions downloaded
scsi0 : Adaptec AHA274x/284x/294x (EISA/VLB/PCI-Fast SCSI) 5.2.4/5.2.0
<Adaptec AIC-7899 Ultra 160/m SCSI host adapter>
scsi1 : Adaptec AHA274x/284x/294x (EISA/VLB/PCI-Fast SCSI) 5.2.4/5.2.0
<Adaptec AIC-7899 Ultra 160/m SCSI host adapter>
Vendor: SEAGATE Model: ST336737LC Rev: 0102
Type: Direct-Access ANSI SCSI revision: 03
Vendor: SEAGATE Model: ST336737LC Rev: 0102
Type: Direct-Access ANSI SCSI revision: 03
Vendor: SUPER Model: GEM354 REV001 Rev: 1.04
Type: Processor ANSI SCSI revision: 02
Vendor: YAMAHA Model: CRW2100S Rev: 1.0K
Type: CD-ROM ANSI SCSI revision: 02
Vendor: SUPER Model: GEM354 REV001 Rev: 1.04
Type: Processor ANSI SCSI revision: 02
Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
Attached scsi disk sdb at scsi0, channel 0, id 1, lun 0
(scsi0:0:0:0) Synchronous at 160.0 Mbyte/sec, offset 31.
SCSI device sda: 72176566 512-byte hdwr sectors (36954 MB)
Partition check:
sda: sda1 sda2 < sda5 sda6 sda7 >
(scsi0:0:1:0) Synchronous at 160.0 Mbyte/sec, offset 31.
SCSI device sdb: 72176566 512-byte hdwr sectors (36954 MB)
sdb: sdb1 sdb2 < sdb5 >
VFS: Mounted root (ext2 filesystem) readonly.
change_root: old root has d_count=3
Trying to unmount old root ... okay
Freeing unused kernel memory: 252k freed
Adding Swap: 2048248k swap-space (priority -1)
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
usb-ohci.c: USB OHCI at membase 0xf8955000, IRQ 10
usb-ohci.c: usb-00:0f.2, PCI device 1166:0220 (ServerWorks)
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 4 ports detected
Winbond Super-IO detection, now testing ports 3F0,370,250,4E,2E ...
SMSC Super-IO detection, now testing Ports 2F0, 370 ...
parport0: PC-style at 0x378 [PCSPP]
parport0: cpp_daisy: aa5500ff(38)
parport0: assign_addrs: aa5500ff(38)
parport0: cpp_daisy: aa5500ff(38)
parport0: assign_addrs: aa5500ff(38)
ip_conntrack (8192 buckets, 65536 max)
eepro100.c:v1.09j-t 9/29/99 Donald Becker
http://cesdis.gsfc.nasa.gov/linux/drivers/eepro100.html
eepro100.c: $Revision: 1.36 $ 2000/11/17 Modified by Andrey V. Savochkin
<[EMAIL PROTECTED]> and others
eth0: OEM i82557/i82558 10/100 Ethernet, 00:30:48:10:9D:72, I/O at 0xc800, IRQ 31.
Board assembly 000000-000, Physical connectors present: RJ45
Primary interface chip i82555 PHY #1.
General self-test: passed.
Serial sub-system self-test: passed.
Internal registers self-test: passed.
ROM checksum self-test: passed (0x04f4518b).
