Actually, I am sorry (I have to eat some crow), I found that I was using 
integers rather than floating point for these parameter values (e.g. RESET 
TEST(37) = 10 rather than RESET TEST(37) = 10.0).

Everything works fine for me now.

Thanks again and sorry for the bother,
Seth

From: [email protected] [mailto:[email protected]] On Behalf Of 
Carpenter, Seth
Sent: Friday, February 22, 2013 11:15 AM
To: Ivonne Gabriela Arroyo; [email protected]
Subject: Re: [seisan] hypocenter locations zero depth

Thanks for your help, Ivonne, your STATION0.HYP file was very helpful!

I found a few interesting things while slowly modifying my file to match yours. 
 A couple of RESET TEST calls seem to foul up hypocenter.  Using either RESET 
TEST(37) or RESET TEST(70), even setting them to the default values, causes the 
depth be fixed shallow through the iterations:
RESET TEST(37) fixes the depth to 0.0
RESET TEST(70) yields either 0.1 or 5.0 dpeth, depending on how other 
parameters are set.

I wonder if anyone else has experienced these issues?

Thanks again!
Seth

From: Ivonne Gabriela Arroyo [mailto:[email protected]]
Sent: Friday, February 22, 2013 9:29 AM
To: Carpenter, Seth
Subject: Re: [seisan] hypocenter locations zero depth

Hi Seth,

Have you solved the problem? I've just changed your TEST parameters for the 
ones I use (with some networks)... just so, without much science or checking 
them... And I got a depth of 20 km. I attach the modified STATION0.HYP here in 
case it helps...
Salud,

Ivonne Arroyo


----- Ursprüngliche Nachricht -----
Von: "Carpenter, Seth" <[email protected]<mailto:[email protected]>>
Datum: Mittwoch, 20. Februar 2013, 15:04
Betreff: [seisan] hypocenter locations zero depth
An: "[email protected]<mailto:[email protected]>" 
<[email protected]<mailto:[email protected]>>
> Hi, all,
>
> I am using SEISAN v9.1 on a 64-bit LINUX computer.  When I try to locate an 
> event, either from within eev or on the command line, I always get zero depth 
> - no matter what I do: try fixing depth with 'F' in column 43 on the 
> epicenter line, set starting depth to various depths in the control line of 
> STATION0.HYP, giving the routine a range of trial depths on the control line, 
> making sure that RESET TEST(31)=3.0 and RESET TEST(96)=1.0.  Also, I've tried 
> using 'generic' phase codes (P, S) and specific codes for these crustal 
> phases (Pg, Sg) with no changes.
>
> I am at a loss of what else to try.  If anyone has any ideas, I would greatly 
> appreciate hearing them.  I've included my sfile and STATION0.HYP in case an 
> obvious problem can be seen in them.
>
> =============================================================
> N. Seth Carpenter
> Seismologist
> Kentucky Geological Survey
> 228 MMRB, University of Kentucky
> Lexington, Kentucky 40506-0107
> (859) 323-0563
> [email protected]<mailto:[email protected]>
>

> _______________________________________________
> seisan mailing list
> [email protected]<mailto:[email protected]>
> http://mailman.uib.no/listinfo/seisan

Dr. Ivonne Arroyo
Marine Geodynamik
GEOMAR Helmholtz-Zentrum für Ozeanforschung Kiel
Wischhofstr. 1-3, Geb.8B
24148 Kiel, Germany
------------------------------------------------------------
Tel. +49-431-600-2417
Fax +49-431-600-2922
www.geomar.de<http://www.geomar.de>
http://www.geomar.de/de/mitarbeiter/fb4/gdy/iarroyo/
------------------------------------------------------------
_______________________________________________
seisan mailing list
[email protected]
http://mailman.uib.no/listinfo/seisan

Reply via email to