billy

this is what it says

Format of control line: 3f5.0,f5.2,i5,2f5.1 Information is:
start depth in km, used if no range of start depths specified (see below)
xnear: distance at which distance weighting start
xfar: distance at which distance weighting is zero, beyond xfar, the phase is not used (local events only)
Vp/Vs ratio
number of start depths
start depth of range of start depths
increment in start depths
NB: If these parameters are used, the fixed initial start depth is not used The input at the bottom is reporting agency used for both hypocenter and magnitudes.

is the I5,2i5.1 is the format

This might not be obvious to all who are not programmers so we might have to explain better, so far there has not been complaints about this.

jens

On Thu, 13 Feb 2014, Billy edson Burgoa Rosso wrote:

Hello Jens,

Thank you very much for your help. Now, I could see more reasonble depth
values and as a consecuence, low RMS.

I just checked the seisan manual on page 99 and I noticed that the format
for this control line doesn't take into account the format for:

number of start depths
start depth of range of start depths
increment in start depths

they are only mentioned.

I also checked the hypocenter manual, however, this has neither the name of
this parameters nor the format of them. Could you please let me know the
complete format of this line?

Thanks again.

Regards,


Billy Burgoa





El Jueves, 13 de febrero, 2014 7:30 P.M., Jens Havskov
<[email protected]> escribió:

billy

it is hard for any program to always find the correct minimum,
particularly if you have both shallow and deep events in the same data
set. then a single starting depth can be a problem. hyp therefor has the
option to use a range of starting depths to avoid the local minimum,
second last line of STATION0.HYP. i have modified you STATION0.HYP and now
the deph with lowest rms is found. manual p 99 (but not so easy to find!)

jens



  On Thu, 13 Feb 2014,
Billy edson Burgoa Rosso wrote:

> Hello Jens,
>
> Yes, I meant hyp (hypocenter).
>
> Regards,
>
> Billy Burgoa
>
>
>
> El Jueves, 13 de febrero, 2014 3:06 P.M., Jens Havskov
> <[email protected]> escribió:
> Billy
>
> do you mean locting with hyp ? we do nto have a program hyp2000
>
> jens
>
> On Wed, 12 Feb 2014, Billy edson Burgoa Rosso wrote:
>
> > Hello SeisAn users,
> >
> > I have a good number of events which I have relocated with hyp2000 and I
> > noticed that some solutions that this locator has obtained are not based
> on
> > the minimum RMS.
> > I selected some events which have high RMS value in order to check the
> > RMS-DEPTH plot and I found out these solutions are not based in the
> minimum
> > RMS. Please find attached an image which presents the rms-depth plot for
> one
> > event. The solution that hyp2000 is taking is based on a local RMS
minimum
> > at 30 km depth, nevertheless, the real minimum RMS is about 80 km depth.
> >
> > Could anybody explain me why hyp2000 is using the solution which doesn't
> > agree with the minimum RMS? Is it possible to set or change any
parameter
> > for hyp2000?
> >
> > I know it is possible to fix the depth editing the s-file, however, I
have
> > lots of events; It could take me a while, if I did one by one.
> >
> > Thanks in advance.
> >
> > Billy Burgoa
> >
> >
> >
>
>
>
>



_______________________________________________
seisan mailing list
[email protected]
http://mailman.uib.no/listinfo/seisan

Reply via email to