It's done !! Thanks a lot !!!
On Sun, Apr 13, 2014 at 6:35 AM, Nick Papior Andersen <[email protected]>wrote: > It seems like your Makefile in the Src directory has been destroyed. > Please restart from a fresh, i.e. delete the siesta directory and > uncompress the tar-file. Then proceed as I suggested. > > > 2014-04-12 16:04 GMT+00:00 jv sharma <[email protected]>: > > Many thanks. I have just prepared in a doc all the output of terminal by >> copy-paste. Attached here.. >> >> >> On Sat, Apr 12, 2014 at 9:23 PM, Nick Papior Andersen < >> [email protected]> wrote: >> >>> Search around for "pipe command to file" in bash/csh (dependent on your >>> shell). >>> >>> Shortly it is: >>> >>> command > command.output 2>&1 >>> >>> which will create the file command.output with the content of the output >>> of the command. >>> >>> >>> 2014-04-12 15:26 GMT+00:00 jv sharma <[email protected]>: >>> >>> sure, but how to export the output of terminal? please.. >>>> >>>> >>>> On Sat, Apr 12, 2014 at 8:44 PM, Nick Papior Andersen < >>>> [email protected]> wrote: >>>> >>>>> Could you please do the previous steps, and between each run the >>>>> command "ls -l" >>>>> Then show us the output of those. >>>>> >>>>> >>>>> 2014-04-12 15:08 GMT+00:00 jv sharma <[email protected]>: >>>>> >>>>> Attached arch.make generated in Obj after following the given steps. >>>>>> Getting the same message again: >>>>>> make: ***No targets. Stop. >>>>>> >>>>>> Please help. >>>>>> >>>>>> >>>>>> On Sat, Apr 12, 2014 at 7:56 PM, Nick Papior Andersen < >>>>>> [email protected]> wrote: >>>>>> >>>>>>> Have you runned: >>>>>>> ../Src/obj_setup.sh? >>>>>>> It is not clear from your mail. >>>>>>> >>>>>>> The order of things: >>>>>>> >>>>>>> $> cd <root of siesta> >>>>>>> $> mkdir -p Obj >>>>>>> $> cd Obj >>>>>>> $> ../Src/configure <options> >>>>>>> $> ../Src/obj_setup.sh >>>>>>> $> make >>>>>>> >>>>>>> That configure is called somewhere else shouldn't matter much. >>>>>>> However, it doesn't clutter your source directory. >>>>>>> >>>>>>> >>>>>>> 2014-04-11 16:12 GMT+00:00 jv sharma <[email protected]>: >>>>>>> >>>>>>> Dear Siesta experts/ users, >>>>>>>> >>>>>>>> I am very new to Siesta. I am trying to compile Siesta-3.2-pl-4 on >>>>>>>> Ubuntu 12.04 LTS. >>>>>>>> My system configuration is: i7 processor, x86_64. >>>>>>>> Everything is going well with the installation. >>>>>>>> Just when it comes to give "make" at the end, I am getting this >>>>>>>> error: >>>>>>>> >>>>>>>> make: ***No targets. Stop. >>>>>>>> >>>>>>>> Attached here the *arch.make* file generated in >>>>>>>> siesta-3.2-pl-4/Src after ./configure >>>>>>>> I have copied this arch.make to siesta-3.2-pl-4/Obj >>>>>>>> >>>>>>>> Please provide some working solution, as I am very eager to work >>>>>>>> with Siesta for some good problems I've in hand. >>>>>>>> Many thanks. >>>>>>>> >>>>>>>> With best regards, >>>>>>>> JVN Sarma, India. >>>>>>>> >>>>>>>> >>>>>>>> >>>>>>>> >>>>>>> >>>>>>> >>>>>>> -- >>>>>>> Kind regards Nick >>>>>>> >>>>>> >>>>>> >>>>> >>>>> >>>>> -- >>>>> Kind regards Nick >>>>> >>>> >>>> >>> >>> >>> -- >>> Kind regards Nick >>> >> >> > > > -- > Kind regards Nick >
