I believe your husband is incorrect.

Marshall

Daniel and Karen Croom wrote:

> Mike,
> Good answers!  About the last question on guage- I asked my husband
> (which I should have done to start with since he's so smart) and he
> said that it's not really 14 or 16, but   .16 and .14 when you're
> talking guages.  It's the same with shotguns.
> Karen
>
> ----------
> > From: M. G. Devour <[email protected]>
> > To: [email protected] silver
> > Subject: Re: CS>silver wire
> > Date: Thursday, August 05, 1999 3:50 AM
> >
> > > The 16 ga. silver wire I've been using was given to me by someone
> > > who said it was "pure".  I just ordered some 14 ga. .999 myself
> and
> > > was surprised to find that I couldn't tell the difference between
> > > the two in size.  So does the 14 ga. actually last  much longer
> than
> > > the 16 ga. ?  ( A dollar a foot longer!?)
> >
> > According to my ARRL Handbook, 16 gauge is 0.051" diameter and 14
> > gauge is 0.064". So, no there's not a *lot* of difference in
> > thickness. However, the cross-sectional area goes up by almost 60%,
> > though, so there is a decent difference in volume of metal.
> >
> > It took me a long time to see a change in diameter on my 12 gauge
> > wires before I finally replaced them. At least a couple of years.
> >
> > As to cost, you probably don't need to pay more than a few bucks a
> > foot, so it's not too much difference, costwise, no matter what.
> >
> > > Anyway, I noticed that the 14 ga. was somewhat softer than the 16,
>
> > > so I figured the purity must be higher.
> >
> > Softness/hardness can vary depending on the processing of the metal,
>
> > totally independant of purity. It'll depend on how the wire has been
>
> > heated and drawn exactly what hardness state it will be left in.
> > Fully annealed, it'll be soft as butter. Drawing, as in pulling it
> > through a die to change its diameter, will harden it.
> >
> > > How does one get their silver tested? No jeweler or pawn shop
> > > around here could do it. By the way, who came up with the guage
> > > numbers getting SMALLER when the wire gets fatter?
> >
> > Good questions!
> >
> > As far as purity is concerned, if you want to make sure of what you
> > have, buy it from a source that will guarantee and document the
> > purity of the material. This includes a lot of chemical and
> materials
> > supply houses that sell to industry and research. They'll provide an
>
> > analysis by batch, either routinely or by request. Expect to pay
> more
> > for the service, though.
> >
> > Otherwise, just making sure the supplier is sending you "fine" or
> > "extra fine" silver wire, at least .999 pure, rather than sterling,
> > should be enough if they are at all competent and honest.
> >
> > There is enough difference between pure silver and sterling that
> > the jewelers and metal workers buying the stuff would know the
> > difference and raise hell with that supplier if they couldn't tell
> > the difference between "fine" and sterling silver!
> >
> > As to wire gauge? Ahh ... ahem ... cough... I don't know. <GRIN>
> >
> > Be well,
> >
> > Mike D.
> > [Mike Devour, Citizen, Patriot, Libertarian]
> > [[email protected]                       ]
> > [Speaking only for myself...              ]
> >
> >
> > --
> > The silver-list is a moderated forum for discussion of colloidal
> silver.
> >
> > To join or quit silver-list or silver-digest send an e-mail message
> to:
> > [email protected]  -or-
> [email protected]
> > with the word subscribe or unsubscribe in the SUBJECT line.
> >
> > To post, address your message to: [email protected]
> >
> > List maintainer: Mike Devour <[email protected]>