Electrodes:  2/16 inch X ?(flat)
             3 1/4 inches wetted length
             1/2 inch spacing

Power:       16 VDC
             20kHz pulsed frequency
             Web site of Pulsed DC generator used
http://web.idirect.com~showcase/althealth/cspulse.htm

Vessel:      Clear 8oz glass(wider at top) 
             3 1/2 inches tall
Additives:   No salt
             No CS solution starter
             
CS cloud:    Visible around 20 min.

Bubble:      Visible around 15 min.

Procedure:   Wiped electrode every 20 min after
             cloud became visible.

Intial current: .2 - .3 ma mesured at electrodes
Final current:  1.4ma measured at electrodes

Solution color: Initally clear
                3 days later; golden yellow
                No visible signs of fallout

Laser pointer:  Can see some sparkles, I have to 
                look hard to see them.

Filtered:       Solution filtered through white 
                coffee filters.  
                Solution filtered 5 times, using
                different coffee filters each time.


I will try the same procedure again paying closer
attention to time, voltages, current, CS cloud, and bubbles.  Will post
results.

                              Thanks 

                              BillH
   
-----Original Message-----
From: M. G. Devour [mailto:[email protected]]
Sent: Friday, October 22, 1999 3:19 PM
To: [email protected]
Subject: Re: CS>Pulsed DC method


I think it would help us if you'd detail your electrode set up and 
power supply parameters: spacing and wetted length, size of vessel, 
etc. Also, you're not using salt, correct? 

Describe your procedure too. How long before you see the cloud 
around the positive and small bubbles from the other electrode? Are 
you wiping the electrodes once in a while?

You have a meter you can use to monitor current during the run, 
right? What's the initial current? Even having to correct for your 
larger surface area, somebody ought to be able to tell if your water 
is good enough to start with.

>      I took 1 tspn after I made it. It burn my chest bad enough
> that I had to drink some water to stop the burning.

That is interesting. We've noticed that some folks are more sensitive 
to the taste than others, but it should be nothing like you describe.

I'm worried that you're using salt as a starter and running way too 
long, in which case you'd be getting a very high concentration of 
fairly big particles. Okay for topical stuff, maybe, but not 
something to experiment with for long term internal use.

>      I looked at the solution with a laser pointer and saw plenty of
> sparkles(I assume this was silver).?

Visible "sparklies" are probably a bad sign. If it's uniformly small 
particle stuff you'll see the beam but no visible particles.

Here's an easy way to get one answer anyway: let the stuff sit for a 
couple of days more. I bet you'll get visible fallout, in which case 
we'll know you made big particles.

To get the "golden" color requires simply using distilled water, no 
salt for a starter, and being patient. Depending on the initial 
conductivity of your water it'll take many minutes to begin visibly 
generating particles. 

Then you will need to go on that way for at least a few tens of
minutes, occasionally removing the electrodes and wiping them off
and stirring things to disperse the "cloud" that forms around the
postitive wire. 

Do this for a while and you'll probably just start to see the slight 
golden color, at which point it's entirely reasonable to stop. As it 
sits overnight it'll darken slightly more, usually.

You'll have made a good few ppm of a reasonably stable CS that 
should, as one of the others said, have a mildly metallic aftertaste 
that is not overly bad to most people.

Let us know how what you're doing compares to this.

Best of luck.

Mike D.

[Mike Devour, Citizen, Patriot, Libertarian]
[[email protected]                       ]
[Speaking only for myself...              ]


--
The silver-list is a moderated forum for discussion of colloidal silver.

To join or quit silver-list or silver-digest send an e-mail message to: 
[email protected]  -or-  [email protected]
with the word subscribe or unsubscribe in the SUBJECT line.

To post, address your message to: [email protected]

List maintainer: Mike Devour <[email protected]>