2001 TV VCR wrote:

> Marshall,
>
> Thank you for your response regarding
> the Zapper and Beck units.  I am sorry
> that I have to disagree with some of your
> statements.  The following electrical
> measurements are incorrect:
>
> The average voltage of an AC signal is
> not zero.  The Beck unit outputs approx
> 50 volts peak equal to around 30 volts
> AC RMS (in layman's terms: average
> voltage).
>

The wave is square so the peak voltage is the same as the RMS.  The .707 factor
is only valid for a sine wave, which the BECK unit is not.  The Beck unit
reverses polarity so that the positive is negative and the negative is positive
after the polarity switch.   I stand by my statement that the average is 0, you
can put an integrator on it and see.  The RMS is not 0, it is 50 volts, but I
did not reference the RMS before.  RMS voltage is not the same as average
voltage, in any terms, laymans or otherwise.  They are very distinct mathmatical
constructs.  For the average you take the integral over time, and divide by
time.  For the RMS you take the integral of the square over time, divide by
time, then take the square root.  The former can give any value from negative
infinity to postive infinty, but the latter can only be 0 or positive.  The
latter is useful for power measurements.  The average voltage on a wall outlet
is 0, but the RMS is about 120.

> The Clark unit (Zapper) could supply
> 5 mA uf your skin resistance was as
> low as 1500 ohms.  But your skin
> resistance is usually above 100,000
> ohms ( less than 0.1 mA).
>

Skin resistance cannot be expressed in ohms.  Since we are talking about a
surface phenomenon it must be in ohms per square cm or square inch.  I just took
a digital voltmeter and measured from one hand to the other holding the small
probes.  My hands were dry and I measured about 50K.  I then connected up the
electrodes I use on the Clark unit and measured about 500 ohms, because it was
contacting about 100 times as much surface area.  It kept dropping though
because my hands would immediately start sweating.  I then wrapped wet paper
towels around each electrode and measured the resistance when I held them in
each hand.  The resistance was around 5 ohms (3 to 10), depending on how hard I
held them.

I stand by my statement before that when holding a large electrode with a wet
paper towel on it, skin resistance is so low as to be virtually irrelevent.

> With skin resistance at 1500 ohms,
> contacting a car battery's terminals
> would be a very shocking experience
> ( yet you don't even feel anything).
>

That is true, because it is DC only.  But both units have an AC component and
thus a tingling can be felt.

> The Clark unit does not put out any
> form of AC.  The 555 timer circuit
> inside is not capable of doing that.
> The output is pulsating DC (no AC).
>

Pulsing DC is by definition the same as AC plus DC.  A 10 volt pulsing DC is
exactly the same thing as a 10 volt square wave AC riding on a DC offset of 5
volts.  They are equivalent and simply two different ways to express the same
thing.  A capacitor will pass AC but not DC.  Put a capacitor in series with the
Clark unit and you will end up with a +/- 4 volt square wave AC signal.  All the
capacitor does is block the DC component.

Marshall


--
The silver-list is a moderated forum for discussion of colloidal silver.

To join or quit silver-list or silver-digest send an e-mail message to: 
[email protected]  -or-  [email protected]
with the word subscribe or unsubscribe in the SUBJECT line.

To post, address your message to: [email protected]
Silver-list archive: http://escribe.com/health/thesilverlist/index.html
List maintainer: Mike Devour <[email protected]>