Ivan 
Some time ago I posted a problem I had with CS. My solution was yellow and 
had something like yellow mucus in it. I noticed later that this mucus was 
from a yellow strand (like a thread) coming off the positive electrode to the 
bottom of the jar. At times, the yellow mucus also covered the sludge on the 
negative electrode. Most of the mucus is reabsorbed into the solution 
overnight. There is a good tyndall. No sparklies. 

I thot it might be the water (WalMart). So I used a previous batch which was 
ok. After 1 batch, same problem again.

This only occurs when I try to make 16oz of CS. I have not altered any 
procedure except added water and increased time to 6 hrs or more when I'm out 
shopping. Tried chilled water per Marshall using old and new water but still 
got yellow color with mucus. No problem using your method with either water 
for 8oz, 3 hrs, 12-15 volts output. Except once or twice, always clear 
solution with visible tyndall.

Now for no apparent reason subsequent batches are clear using old water and 
new water for comparison. However, tyndall is very light. My output voltage 
is now 9-12 volts

What do you think?
Wong

I've kept some records. Maybe this will help some Newbies.
           oz      out                                           as of
Date  Water  volts  hrs  color      tyndall     11-30-99           tyndall      
    
7-7     16  12-15   6   clear     medium     clear                yes on all. 
Lite to
7-25    16  12-15   8   clr       med           clr                   medium.
10-6       8    12-15   3   clr       med        lite yellow
10-6        8   12-15   3   clr       med        clr
10-9         8  12-15   3   clr       med           lite yellow                 
10-10      8    12-15   3   clr       med        yellow 
10-10     16    12-15   6   note 1   med           tinge of yellow
10-12     16    12-15   6   note 1   lite             tinge of yellow           
10-12      8    12-15   3   clr       lite             clr              
10-13   16  12-15   7   note 2   lite            clr        
10-14   16  12-15   6   note 3   lite             tinge of yellow
10-14    16 12-15   6   clear     lite           clr    
10-15      8    12-15   3   clear     lite             clr  
10-16   16  12-15   6.3 clear     lite             clr  
10-18   16  9-12    6.3 note 4   lite             clr
10-19    16 9-12    7   note 4   lite              clr
10-20   16  9-12    8   note 4   lite              tinge of yellow
10-21   16  9-12    6.3 note 4   lite              clr
10-22   16  9-12    6.3 note 4   lite              clr
10-23   16  9-12    6.3 note 4   lite              clr  
10-24   16  9-12    9.3 note 4   lite              clr
10-27   16  9-12    7   note 5  lite               clr  
11-15   16  9-12    7   clear   lite               clr  
11-23   16  9-12    8   clear   lite               clr
11-23 16    9-12    8   clear   lite               clr
Note 1. yellow/thick mucus strands
Note 2. yellow/new water used
Note 3. yellow/mucus strands/ 40 degree water/Marshall  
Note 4. clear/yellow strand from anode
Note 5. clear/no detectable mucus   
                    
Wall transformer set @ 9 volts, output 12-15 volts. Set at 7 1/2 volts, 
output 9-12 volts.                                                          
                                                        
                                                            
                                                            
                                                            


Liz 

I got it again. A string of mucus, not treeing, from one of the wires, 
positive I think, almost to the bottom of the jar. I got most of it out with 
a plastic straw (adhesion).
Sure this is silver?
wong

In a message dated 6/17/99 1:25:33 PM Pacific Daylight Time, 
[email protected] writes:

<< Wong: If that "mucus" is coming off one of the wires, it's silver 
sintering off the electrodes.  It tends to look a little like mucus as it 
hangs suspended in the water.  
 
 Liz >>

Subj:    Re: CS>power supply
Date:   10/20/1999 3:33:11 AM Pacific Daylight Time
From:   [email protected] (Ivan Anderson)
Reply-to:   <A HREF="mailto:[email protected]";>[email protected]</A>
To: [email protected], [email protected]

What voltage are you running these days Wong?

The resistor value can be calculated using R = V/I (resistance in ohms
equals the voltage divided by the current in amps. For 12 Volts and
assuming a 2mA  short circuit current then a 6000 ohm (6K0) resistor
will suffice but is probably not necessary.
[ I have found in my system the load resistance (CS solution) is about
20K ohms at 12 to 15 ppm. As the load resistance is higher than the
determined limiting resistor value, the actual current does not reach
the chosen current, in fact the limiting resistor further limits the
current, in this case, to 0.46mA (12V divided sum of load and limiting
resistor) and is therefore not required] The actual current without a
limiting resistor is 0.6mA which I feel is a pretty good maximum.

For  36V in my system an 18K0 resistor will limit the short circuit
current to 2mA. In actual current terms, the current will be 0.95mA,
with a load resistance of 20K ohms.

For a 27V a 7K0 resistor will limit the actual current to 1mA and will
have a short circuit current of about 4mA.

This resistor (just a cheap 1/4 watt resistor from your local electronic
shop) is wired in series, that is, placed between one electrode and its
power source wire. You don't need to solder it, just wrap one leg around
the silver electrode and grab the other leg with the alligator clip of
your power supply lead.

Regards - Ivan.


--
The silver-list is a moderated forum for discussion of colloidal silver.

To join or quit silver-list or silver-digest send an e-mail message to: 
[email protected]  -or-  [email protected]
with the word subscribe or unsubscribe in the SUBJECT line.

To post, address your message to: [email protected]
Silver-list archive: http://escribe.com/health/thesilverlist/index.html
List maintainer: Mike Devour <[email protected]>