You know, the idea is just wonderful! Colloidal silver is so useful,
it would be great if we could easily make up a batch whenever we wanted
to. All we'd need is a simple off-the-shelf unit, a readily available
catalyst to turn the distilled water into a semiconductor, some
distilled water, and vavoom, there's the colloidal silver. Just think,
you wouldn't have to keep paying high prices for colloidal silver and
you could make as much colloidal silver as you wanted. The idea's great,
if only it were as simple as all that.
OFF-THE-SHELF UNITS
All of the off-the-shelf units made available to the public, so far,
have some serious design flaws. In fact, there are so many flaws, we'd
better go over each major flaw area, one at a time.
Alternating Current (AC) verses Direct Current (DC) - With
direct current, only one of the two plates of silver is giving
off silver particles because the current is only flowing one direction.
With alternating current, the direction of the current changes
back and forth, making it possible for both plates to give off silver
particles, alternately. Most commercial manufacturers who make the
super-Tyndall effect colloidal silver (If you'd like to read more about
the super-Tyndall effect, click What Does Colloidal Mean?.) use alternating
current so that both silver plates contribute silver particles.
Unfortunately, virtually all of the off-the-shelf home units are battery
operated, i.e., using DC. This means, at best, they are working half as
efficiently as their AC counterparts.
Voltage and Amperage - One of the really sensitive variables
affecting the quality of colloidal silver is the amount of voltage
between the silver plates as well as the amperage (a measurement of the
amount of current). Battery powered off-the-shelf home units typically
use a nine volt battery. These nine volt batteries usually only provide
about nine volts (big surprise, right?). Commercial manufacturers often
use ten to twenty times that amount of voltage in order to produce the
desired product. A low voltage, like nine volts, can often only pull off
the plate very small silver particles, smaller than the minimum 5nm (nm
= nanometer = one thousandth of a micron = one billionth of a meter)
colloidal limit. As a result, such suspensions are predominently
molecular, and can, therefore, promote the build up of a silver toxicity
(You may want to click So,
What's Colloidal Silver? to read more about the importance of
the colloidal limits when it comes to silver).
Battery operated, off-the-shelf, home units usually provide very low
amperages (Amp), as well. A fraction of one Amp is often the maximum
amount of current used in home units. Commercial manufacturers typically
use several Amps of current with their higher voltage equipment. Since
the amperage and voltage play such a significant role in the quality of
the product, it raises serious doubts whether the quality of colloidal
silver could possibly be the same, despite the huge differences in
voltage and amperage between the off-the-shelf, home units and the
commercial manufacturers. It's probably fair to assume the colloidal
silvers are NOT the same.
There is a strong reason for the low voltage and amperage output of
home units. If you think about it, it's the issue of safety that's the
real reason for the low voltage and amperage. Making available a unit
which supports high voltage and amperage would make it virtually
impossible to obtain product liability insurance. One person
electrocuting him- or herself on a nifty high powered home unit would be
devastating. Working with liquids around high voltages and amperages is
begging for disaster. Therefore, there is virtually no choice but to
provide only low voltage and amperage units where electrocution is
minimized. Unfortunately, such safety constraints significantly effect
the quality of colloidal silver.
Plate Shape and Orientation - Of equal importance with the
type of current, the amount of current and the voltage is the shape of
the silver plates and how they're oriented with each other. Commercial
manufacturers use flat plates. The flat plates parallel each other
giving as much active surface area to the opposite plate as possible.
The distance (the gap) between the plates in commercial units is usually
very small.
In contrast, most home units use plates which are actually
cylindrical rods. This means there is very little active surface because
of the cylindrical rod's shape. Further, with these rods, the distance
between the plates (the gap) changes as one moves around the cylinder.
In addition, the overall gap between the rods in a home unit is much
greater then that between the plates in commercial units. As you might
expect, the mass of the silver particles which are drawn from the widely
gapped home unit rods is much smaller. Again, the design of the home
units promotes the development of a molecular suspension rather than a
colloidal suspension.
READILY AVAILABLE CATALYSTS
If there were nothing wrong with the off-the-shelf home unit as far
as design, the next hurdle, the catalyst, might really be the biggest
problem. You see, the substances used in the home as a catalyst really
aren't that great when it comes to colloidal silver. For example, if one
uses just regular table salt (NaCl) or sodium chloride as the catalyst,
one always runs the risk of splitting the salt molecule into its
constituent elements, sodium and chlorine. Chlorine happens to be very
toxic when swallowed. Some even falter when it comes to high dosages of
sodium. Thus, in a colloidal silver home unit, with its tendancy towards
a molecular silver suspension, adding chlorine will give you a wonderful
molecular solution called silver chloride (AgCl) which, if taken in
large quantities, can poison you quite nicely.
Commercial manufacturers use other catalysts which can ONLY be
used in a commercial installation with the proper laboratory equipment.
The companies that sell these catalysts will not sell it to you at all
if you're going to use it in a home environment. Strict laws make this
absolutely necessary. As a result, the catalysts used to make the
super-Tyndall effect colloidal silver cannot be used in the home.
Instead, only poor substitutes are available. As a result, even with a
home unit designed properly, obtaining the right kind of catalyst like
commercial manufacturers is still impossible for home use.
DISTILLED WATER
Of the three areas necessary to make colloidal silver, obtaining some
distilled water is the least problematic. You can obtain distilled water
at many locations. In a way, it's too bad picking up a well designed
home unit along with the necessary catalyst is NOT as easy as
picking up the necessary distilled water.
Today, most commercial manufacturers of colloidal silver use water
that is even better than distilled water. Usually, they use water that
has been demineralized, has been run through a reverse osmosis machine,
before it's distilled once or twice. Some are even using injectable
quality water. Again, this helps provide a clean, safe colloidal silver.
RECOMMENDATIONS
At least so far, the off-the-shelf home units are not designed well
for manufacturing a high quality of colloidal silver. Some of the design
flaws can be rectified quite easily. However, the problem of safety is a
major hurdle which must be addressed before home units can provide
super-Tyndall effect colloidal silver. Anything which doesn't exhibit
that profound Tyndall effect means a high percentage of the suspension
is not colloidal. With silver, non-colloidal leads to toxicity.
When it comes to a commercial grade catalyst, the home manufacturer
is the loser. It is just not available. The catalysts which are
available in the home just don't do the job very well and may even
contribute to the toxicity of the end product. So the catalyst issue is
still a real blockade to home colloidal silver production.
So, the bottom line to home production is, DON'T!! Check out
where you can buy the super-Tyndall effect colloidal silver and compare
prices. Hopefully, not everybody selling colloidal silver is filled with
greed. The right stuff makes all the difference in effectiveness AND
safety.
This is the end of this Chapter. You might want to click Can Science Prove Something Is
True? to see the next chapter titled, THEORIES.