Hello Janine,

Saturday, March 29, 2003, 2:40:51 PM, you wrote:

JM> Tony,

JM> My Dr. is a little gun shy about lead as we live in an area(North Idaho)
JM> where there is a lot of silver mining and lead has been know to be a
JM> problem. He has seen a lot of people with lead poisoning. I am considering
JM> having my water and cs tested for lead just to make sure. I don't think cs
JM> made with .999 pure silver have any more lead than your avg. water.

JM> Sincerely,

JM> Janine Meunier
JM> [email protected]


JM> -----Original Message-----
JM> From: Tony Moody [mailto:[email protected]] 
JM> Sent: Friday, March 28, 2003 11:29 PM
JM> To: [email protected]
Subject: Re: CS>>Lead

JM> Janine,
JM> Could you ask your medical professional to quote some sort of relative 
JM> figures or quantities . Like drinking water has 'somuch' lead in it and CS 
JM> made with distilled water has 'so much ' lead in it. Maybe you could ask him

JM> for references which you, or we, could follow up.

JM> We know how poisonous lead is and mercury is more poisonous. But the medical

JM> and dental lot have promoted mercury for dental fillings. So can you believe

JM> what they are saying now.
JM> sincerely
JM> Tony


JM> Janine Meunier wrote:
>> Hi,
>> 
>> I haven't been here in awhile but still using CS going on 2-3 years. I was
>> wondering if anyone has ever had their homemade CS tested for lead
JM> content?
>> I make my CS with the 3- 9 volt battery method and 2 .999 silver ingots.
>> Recently a medical professional said that there is lead in the silver and
>> that the levels are too high to be safe. What do you guys have to say?
>> Thanks very much.
>> 
>> Sincerely,
>> Janine 
>> 


Janine, all:

Simple math here. Let's assume that ALL of the contaminants in your
.999 silver are lead (which they aren't... Actually, .999 silver is
nearly always .9995, at least from every source I have personally
looked at).

YOUR CS:
20 PPM silver... Equals 20 milligrams per liter....20X0.001=0.02, or
0.02 milligrams per liter, or 0.02 PPM contaminants. This would be 2
parts per hundred million, or 20 PPB (parts per billion). The maximum
contaminant level (or MCL) for lead in drinking water in the United
States, from a municipal supply, is 15 PPB (parts per billion).

So... We would have a lead level in excess of the MCL for drinking
water, but ONLY if the contaminants in your silver were PURE LEAD and
nothing else, and ONLY if your CS was 20 PPM in concentration.

Now, for a more realistic look. 999 fine silver is allowed to have a
total of 0.001 (1/10 of 1 percent, or 1000 PPM) TOTAL impurities. But,
the MAXIMUM levels of various impurities is as follows....
copper: 800 PPM
lead: 250 PPM
iron: 200 PPM
bismuth: 10 PPM

So, applying this to our above situation, we find that the maximum
lead content we will achieve is 5 PPB lead. This is ONE THIRD the
amount allowed in a municipal source of drinking water.

Should you decide to get your CS tested for lead content, take the
time to do a proper analysis, and also send in a sample of the SAME
distilled water that you used to make it with (from the same batch,
same container). This will give you a baseline to compare with.
Without this baseline, you will NEVER determine if it is the silver
which is contaminated, or the distilled water!

All of this comes together to say, once again, that the "medical
professional" you consulted with doesn't have a clue as to what they
are talking about. Unfortunately, this is not uncommon.



-- 
Best regards,
 Solar                            


--
The silver-list is a moderated forum for discussion of colloidal silver.

Instructions for unsubscribing may be found at: http://silverlist.org

To post, address your message to: [email protected]

Silver-list archive: http://escribe.com/health/thesilverlist/index.html

List maintainer: Mike Devour <[email protected]>