I cold started, warm started... everything with the unit. The one I had sitting on my desk was only about 3 feet from the ap I was testing it with... I know both of them were getting packets.
I grabbed another APP this morning went back out there... messed with the unit that was currently out there... nothing.. still dead... grabbed the new one, plugged it in, hoped into it (one of the units I was playing with last night) and it works great... didn't have a single issue, didn't replace anything else except the unit it's self.. Although... just as an FYI for everyone... If you use the APro Indoor's and only hook one ant up to them (mount the box in a NEMA or something) MAKE SURE you tell it to only use that one ant. I was seeing the RSSI jump up to -70 every 3 or 4 seconds and LQ go down to about 20%... then go right back up to -24 and a LQ of 94%... Told the unit to only use that one interface, and it's stable at -24 now... and the speeds through it doubled... But I guess I'm going to see if I can redo these two units with simpleDeploy.. if not.. their getting RMA'ed later today... -----Original Message----- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] Behalf Of IVAN KORSHUN Sent: Tuesday, June 17, 2003 3:28 AM To: [EMAIL PROTECTED] Subject: Re: [smartBridges] Wireless port problems... Shawn Mitchell, It is old_bugs firmware. If " warm restart ", AP expects the ANY_packets_interrupts from a Aether, if the packets are that there are no problems :) If " cold restart " (off/on power) no problems. -Ivan -----Original Message----- From: "Shawn Mitchell" <[EMAIL PROTECTED]> To: <[EMAIL PROTECTED]> Date: Tue, 17 Jun 2003 01:08:52 -0500 Subject: [smartBridges] Wireless port problems... > > Ok... Here's a big problem that's starting to just p*** me off... > > airPoint Pro (indoor) > > Unit 1: Will not do any RF Output when in repeater mode... If I set it to > AP mode, and reset it (holding in the reset button) and clicking the factory > default's button... and spend 10 min or so doing this the unit will start > sending RF packets... > > Now, the counters show that it's getting rf packets, but not a single tx > packet... not even beacon's... > > Now, Unit 2: > > Same problems as Unit one, except with a twist... On the Tx packets for the > RF interface, I see one broadcast... never anymore than that... and the > Ethernet interface keeps resetting about every 2 min... This one is just > going to be a normal AP... > > > Has anyone ever seen anything like this before? On Unit 1 I'm trying to > Associate it to an AP. I can see many AP's, but any of them I double click > on it just counts down to 0 seconds and gives me the failed message. If I > put the info (ESSID, BSSID, etc) in manually, as soon as I hit the Set > Values button, it pop's up an error telling me it can't set it... > > > Any idea's? Or do I have to RMA these units? I already have a handful of > other ap's that I am having to rma... > > The PART-15.ORG smartBridges Discussion List > To Join: mailto:[EMAIL PROTECTED] (in the body type subscribe smartBridges <yournickname> > To Remove: mailto:[EMAIL PROTECTED] (in the body type unsubscribe smartBridges) > Archives: http://198.63.203.6 The PART-15.ORG smartBridges Discussion List To Join: mailto:[EMAIL PROTECTED] (in the body type subscribe smartBridges <yournickname> To Remove: mailto:[EMAIL PROTECTED] (in the body type unsubscribe smartBridges) Archives: http://198.63.203.6 The PART-15.ORG smartBridges Discussion List To Join: mailto:[EMAIL PROTECTED] (in the body type subscribe smartBridges <yournickname> To Remove: mailto:[EMAIL PROTECTED] (in the body type unsubscribe smartBridges) Archives: http://198.63.203.6
