Christos,
I am having EXACTLY the same problem! I have 2 APPO turned on at the site right now. I upgraded to the latest firmware as per sb tech support -then I went on vacation for a week- and when I came back to test today, there is no change. Did you finally get this resolved somehow?
Thanks,
Sevak
On Wed, 2003-07-30 at 13:16, Christos Ventouris wrote:
If we accept the fact that it’s a problem of the cables, how can we explain the fact that after a power down for 15-20’ the AP works ok for a little time and then goes bad again ?
-----Original Message-----
From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of Scott Damron
Sent: Wednesday, July 30, 20038:11 PM
To: [EMAIL PROTECTED]
Subject: RE: [smartBridges] Overheating Airpoint Outdoor Pro ?
Actually, humidity will cause it as well, I am pretty sure you have quite alot of humidity there (?) I wish I were there, I would confirm or deny it for you!! :)
Scott
-----Original Message-----
From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of Christos Ventouris
Sent: Wednesday, July 30, 2003 9:47 AM
To: [EMAIL PROTECTED]
Subject: RE: [smartBridges] Overheating Airpoint Outdoor Pro ?
Well I’d go and check it, but It’s summer here in Greece and It has never rained since I’ve installed the AP on the mast J
-----Original Message-----
From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of John Speakman
Sent: Wednesday, July 30, 2003 7:36 PM
To: [EMAIL PROTECTED]
Subject: RE: [smartBridges] Overheating Airpoint Outdoor Pro ?
Is your RF cable OK? This sounds a little like water ingress into the cable.
-----Original Message-----
From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]On Behalf Of Christos Ventouris
Sent: 30 July 2003 17:33
To: [EMAIL PROTECTED]
Subject: RE: [smartBridges] Overheating Airpoint Outdoor Pro ?
Hi Scott,
I’ve already tried that. I’ve performed a site survey and there are no other clients or APs working on the same channel or other interfering channels.
-----Original Message-----
From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of Scott Damron
Sent: Wednesday, July 30, 2003 7:30 PM
To: [EMAIL PROTECTED]
Subject: RE: [smartBridges] Overheating Airpoint Outdoor Pro ?
Possibly you have some interference, and not an overheating issue. I have seen this myself, and it happened when some wise guy decided to put up a linksys AP and share out his connection with his neighbors. It was running on the same channel as our AP. You might do a little war driving and see what you can see before you assume it is the AB.
Scott
-----Original Message-----
From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of Christos Ventouris
Sent: Wednesday, July 30, 2003 9:28 AM
To: [EMAIL PROTECTED]
Subject: [smartBridges] Overheating Airpoint Outdoor Pro ?
Hello All,
I have an Airpoint Outdoor Pro (later reffered as AP) which I’ve been using for 2 months now with no problems. It is operating in Client Bridge mode with
Firmware version 1.6j6.
It’s been over 10 days I am having serious problems with it. The Link Quality graph on the Link Status graph appears spiky with values ranging from
90% to 60% at all times and changing constantly every 2 secs (Usually It was steady on 90-95%). I’m using the FTP service on a remote computer to check the speed of the link and I was surprised to see that I was downloading with an average of 3-10kb/sec and the transfer rate was also going up and down until in a couple of minutes the transfer failed. Note that my AP is never disassociated from the host AP (I tried the v1.6j8 firmware with no change in my situation)
After a lot of tests I got angry and unplugged the AP from the power and let it cool for about 20 minutes. When I plugged it back on It seemed to be working perfect , with the Link Graph I was used to have and FTP transfer rates I always enjoyed, but only for a minute or less. It fell back to this state I described earlier. I repeated the on/off test for the same period and I had the same results.
I believe that something is overheating. But I wonder, is it the power supply that goes nuts or the AP itself ? Anyone with experience on this matter would be very helpful.
Thank you,
Christos Ventouris.
|
