Good test to try! Will do. Thanx! -----Original Message----- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] Behalf Of Shawn Mitchell Sent: Saturday, August 16, 2003 12:15 PM To: [EMAIL PROTECTED] Subject: RE: [smartBridges] 2 New aPPo's DONT WORK
Something you might try just for grins... Take the little crossover extention that comes with the AB's, and plug it into it and then into the hub. I had an ABBO, brand new w/ the pig tail, the ethernet kept crashing... I did that, and it started working somewhat correctly... very unusual and weird... -----Original Message----- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] Behalf Of The Wirefree Network Sent: Saturday, August 16, 2003 10:02 To: [EMAIL PROTECTED] Subject: RE: [smartBridges] 2 New aPPo's DONT WORK I had 1400 size pings running all night to this aPPo setup and the airBridge on the other side (and vice versa). I graphed it all with MRTG and it looks fine. I dont know why it didnt work on the roof?? I am going to put a 70 ft piece of cat5 on it this morning before I go install it at the repeater location...I will see if that is an issue. Sully -----Original Message----- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] Behalf Of The Wirefree Network Sent: Saturday, August 16, 2003 1:00 AM To: [EMAIL PROTECTED] Subject: RE: [smartBridges] 2 New aPPo's DONT WORK Shouldn't have to do this with a 45 ft run that works with the old unit??? I am using the supplied power supply (which is not one of the super old recalled ones). Thanks for the advice though....really!! Sully -----Original Message----- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of Tom Haynes Sent: Saturday, August 16, 2003 12:14 AM To: [EMAIL PROTECTED] Subject: RE: [smartBridges] 2 New aPPo's DONT WORK Sully, that sounds a lot like a power quality issue. Can you check the actual voltage on the cable JUST BEFORE IT GOES IN THE APPO using an analog volt meter? You should see no less then 8vdc and the needle should not move any. If the needle swing any then you have a cable or power problem. How long is the cat5 and what power supply are you using? -----Original Message----- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of The Wirefree Network Sent: Friday, August 15, 2003 11:32 PM To: 'The Wirefree Network'; [EMAIL PROTECTED] Cc: [EMAIL PROTECTED]; [EMAIL PROTECTED]; [EMAIL PROTECTED] Subject: RE: [smartBridges] 2 New aPPo's DONT WORK Oh...forgot one thing. During the 5 minute period of the aPPo's working...I was watching the statistics and noticed that the unit's kept rebooting. The statistics would keep going back to zero. Then it just died. What the heck is going on?!?!? Sully -----Original Message----- From: The Wirefree Network [mailto:[EMAIL PROTECTED] Sent: Friday, August 15, 2003 9:26 PM To: '[EMAIL PROTECTED]' Cc: '[EMAIL PROTECTED]'; '[EMAIL PROTECTED]'; '[EMAIL PROTECTED]' Subject: 2 New aPPo's DONT WORK Importance: High I received an aPPo from Electro-Comm that I PAID EXTRA for to have it overnighted to me so that I could replace a faulty aPPo (firmware issue). First thing I did was upgrade the firmware like the STICKER says on the box. Then burned in my settings with simpleDeploy. All went well. I replaced it and it worked like a champ--all clients reassociated! Woohooo!! Five minutes later clients started dropping off and the Ethernet side died! I did a power reset and it came back up but only a few clients associated back up with it. So...I waited a couple minutes and the Ethernet side died again. I reflashed it...I lowered the firmware...I reflashed it...I upgraded the firmware...I replaced the powershot twice...I did EVERYTHING! The Ethernet side would keep crashing. In case it matters to anyone...it was only 70 degrees here today. So...I put my old unit back up (after only 3 hours of MY LABOR WAISTED) and it worked fine. My old unit periodically crashes..and that is why I am RMAing it. Yesterday...I received my stock (and spares) from Electro-Comm. I started the process ALL OVER AGAIN...with the exact same results (3 more hours waisted). The Ethernet side DIED after 5 minutes. I am once again back on my old aPPo...I have a bunch of pissed off customers....and I am VERY pissed myself. I am soooo sick of spending hours upon hours replacing bad equipment. sB...can you please send me 2 aPPo's from Singapore...that you have actually verified work for longer than 5 minutes?!?! Sully The PART-15.ORG smartBridges Discussion List To Join: mailto:[EMAIL PROTECTED] (in the body type subscribe smartBridges <yournickname> To Remove: mailto:[EMAIL PROTECTED] (in the body type unsubscribe smartBridges) Archives: http://archives.part-15.org The PART-15.ORG smartBridges Discussion List To Join: mailto:[EMAIL PROTECTED] (in the body type subscribe smartBridges <yournickname> To Remove: mailto:[EMAIL PROTECTED] (in the body type unsubscribe smartBridges) Archives: http://archives.part-15.org The PART-15.ORG smartBridges Discussion List To Join: mailto:[EMAIL PROTECTED] (in the body type subscribe smartBridges <yournickname> To Remove: mailto:[EMAIL PROTECTED] (in the body type unsubscribe smartBridges) Archives: http://archives.part-15.org The PART-15.ORG smartBridges Discussion List To Join: mailto:[EMAIL PROTECTED] (in the body type subscribe smartBridges <yournickname> To Remove: mailto:[EMAIL PROTECTED] (in the body type unsubscribe smartBridges) Archives: http://archives.part-15.org The PART-15.ORG smartBridges Discussion List To Join: mailto:[EMAIL PROTECTED] (in the body type subscribe smartBridges <yournickname> To Remove: mailto:[EMAIL PROTECTED] (in the body type unsubscribe smartBridges) Archives: http://archives.part-15.org The PART-15.ORG smartBridges Discussion List To Join: mailto:[EMAIL PROTECTED] (in the body type subscribe smartBridges <yournickname> To Remove: mailto:[EMAIL PROTECTED] (in the body type unsubscribe smartBridges) Archives: http://archives.part-15.org
