The newest versions of the firmware there is a setting to allow you to modify the RSSI to DBM conversions and lets you put in your own figures to give you more accurate readings. This is found in the advanced tab of airbridge units.
oting Dominic Kilbride <[EMAIL PROTECTED]>: > Hi all, > Martin pointed out that the RSSI signal levels and link quanlitys are not > correct in simple monitor. This is definatly my experiece as well. Is this > the case for all versions and products? Is there anything you can do about > it? > > /Dominic > Svenska Antennspecialisten AB > http://www.antennspecialisten.se > > -----Ursprungligt meddelande----- > Fr�n: [EMAIL PROTECTED] > [mailto:[EMAIL PROTECTED] Martin Moreno > Skickat: den 5 september 2003 06:19 > Till: [EMAIL PROTECTED] > �mne: Re: [smartBridges] Distance and Links > > > Keep in mine the RSSI and Link qaulity are not correct in the SB product > you > need to log into you access point and get a true reading (if it is not an > APPO) > and or do the manual calculation as to what the true numbers are. > > > Quoting Rudolph Worrell <[EMAIL PROTECTED]>: > > > I have notice a lot of talks here regarding links, distances, antenna > types > > > > and Amps. It is a little scary because sB braggs a 21 mile range with > proper > > > > antenna (24dbi) in open space. I took that as a guarantee and I am > betting > > on > > it. > > > > So far I have been able to get a signal percent or 22% with a 14dbi > > directional antenna using the AirNic and a laptop at 6 miles with decent > line > > > > of site. When the 24dbi grid is added to the equation I get about 90-100 > > percent at the same 6 miles away. Is this good. Does anyone else get > the > > same or better. > > > > If this works at 6 miles at near 100 with decent LOS I am going to bet > that > > it > > will do the same at 10-15 with clear LOS on a tower without an amplifier. > > Anyone done this? > > > > Last question. What are your feelings on using utility poles for > > distribution > > of your services and do you think $700/month is too high? > > -- > > Rudolph Worrell > > President > > Phone:(540)664-3950 > > Fax:(270)458-6431 > > www.wave2net.com > > > > > > > > > > > > ------------------------------------------------- > > This mail sent through IMP: http://horde.org/imp/ > > ----------ANNOUNCEMENT---------- > > Don't forget to register for WISPCON IV > > http://www.wispcon.info/us/wispcon-iv/wispcon-iv.htm > > > > The PART-15.ORG smartBridges Discussion List > > To Join: mailto:[EMAIL PROTECTED] (in the body type subscribe > smartBridges > > <yournickname> > > To Remove: mailto:[EMAIL PROTECTED] (in the body type unsubscribe > > smartBridges) > > Archives: http://archives.part-15.org > > > > > Martin Moreno > Blazen Wireless > 909-907-4106 > www.blazenwireless.com > ----------ANNOUNCEMENT---------- > Don't forget to register for WISPCON IV > http://www.wispcon.info/us/wispcon-iv/wispcon-iv.htm > > The PART-15.ORG smartBridges Discussion List > To Join: mailto:[EMAIL PROTECTED] (in the body type subscribe > smartBridges <yournickname> > To Remove: mailto:[EMAIL PROTECTED] (in the body type unsubscribe > smartBridges) > Archives: http://archives.part-15.org > > > ----------ANNOUNCEMENT---------- > Don't forget to register for WISPCON IV > http://www.wispcon.info/us/wispcon-iv/wispcon-iv.htm > > The PART-15.ORG smartBridges Discussion List > To Join: mailto:[EMAIL PROTECTED] (in the body type subscribe smartBridges > <yournickname> > To Remove: mailto:[EMAIL PROTECTED] (in the body type unsubscribe > smartBridges) > Archives: http://archives.part-15.org > Martin Moreno Blazen Wireless 909-907-4106 www.blazenwireless.com ----------ANNOUNCEMENT---------- Don't forget to register for WISPCON IV http://www.wispcon.info/us/wispcon-iv/wispcon-iv.htm The PART-15.ORG smartBridges Discussion List To Join: mailto:[EMAIL PROTECTED] (in the body type subscribe smartBridges <yournickname> To Remove: mailto:[EMAIL PROTECTED] (in the body type unsubscribe smartBridges) Archives: http://archives.part-15.org
