Re: [smartBridges] Why not to use smartBridge...

[Mark Radabaugh]

ï You didn't somehow manage to create a bridge loop?   It will cause exactly the packet loss behavior you are seeing.   Mark ----- Original Message ----- From: Rick Kosick To: [EMAIL PROTECTED] Sent: Thursday, November 13, 2003 9:17 AM Subject: Re: [smartBridges] Why not to use smartBridge... Well I am very sure that the other side is not talking because I can't get that to work at all. Plus, there is not enough capacity on the wireless side to drain a 100Mbps switch. I'm thinking that maybe somehow the APPO in Access Point mode is maybe arp'ing for everything to be sent through it? Who knows. Weird. ----- Original Message ----- From: Blazen Wireless To: [EMAIL PROTECTED] Sent: Thursday, November 13, 2003 9:14 AM Subject: Re: [smartBridges] Why not to use smartBridge... HEHe that sucks maybe thats what part of my problem at the tower is but mine is a little different, when I see traffic from users to the APPO the latency on the network from the APPO to any other users goes WAY WAY WAY up!   See if you can turn the ant away at the noc so it is not picking up your remote APPO and stop all traffic and see if that has any affect just curious... OR just plug the appo in and dont hook up the ant and ping it and see what you get? ----- Original Message ----- From: Rick Kosick To: [EMAIL PROTECTED] Sent: Thursday, November 13, 2003 6:05 AM Subject: Re: [smartBridges] Why not to use smartBridge... I don't know the actual version number but I just downloaded it off the website in the past few days and it is the very latest on both sides.   This part about it bringing the switch to its knees is VERY disturbing because a switch, by its design, should not allow that to happen normally. I can see it happening to a hub.   I was working on this remotely (from home) at late hours both times and had to drive to the NOC to remedy it because I couldn't access any machines via PC Anywhere. The whole network crashed basically. === Rick Kosick StarLinX Internet Service ----- Original Message ----- From: Blazen Wireless To: [EMAIL PROTECTED] Sent: Thursday, November 13, 2003 8:59 AM Subject: Re: [smartBridges] Why not to use smartBridge... Interesting what firmware were you using which should not affect your switch like that just curious to know..   ----- Original Message ----- From: Rick Kosick To: [EMAIL PROTECTED] Sent: Thursday, November 13, 2003 5:39 AM Subject: [smartBridges] Why not to use smartBridge... So far I've come up with three good reasons to not continue to use smartBridges but I'm open to suggestions for fixing these problem. Pardon my frustration but I have 3 years of wireless experience and its taking me more than 10 hours of fiddling to get a simple Wireless Bridge to Wireless Bridge up and running and I am sitting here with more problems than solutions right now.   1) Last week I plugged the ethernet side of an APPO into an APCC PNET4 ethernet surge supressor where there where three other devices plugged in. This caused severe packet loss on the other devices. Pinging the other devices between each other would result in 4 out of 10 pings timeing out.   SOLUTION:    Bypass the ethernet surge supressor.   2) Right now I have two APPO's configured in Wireless Bridge mode (which won't work, see #3). At my NOC side its plugged into a D-Link DES3226 Managed Switch. If I put the APPO into Access Point mode, it KILLS the traffic on my switch entirely to the point where workstations and servers can barely reach each other. As soon as I unplug the APPO's ethernet connection from the switch, immediately everything goes back to normal. This has happened twice now in my quest to get my wireless link working.   SOLUTION:    No idea. Maybe avoid Access Point mode?   3) I have to admit I did enjoy 3 minutes of Wireless Bridge mode where everything worked as it was expected, but I got adventerous and enabled WEP. This did not work out for some reason and now, after disabling WEP... I cannot get the Wireless Bridge mode to work again. I've reset to Defaults and started over, still nothing. I simply cannot get Wirless Bridge to Wireless Bridge mode to work at this point. I've been through the "recycling both sides", "double checking MAC#'s", etc. You'd think that if this was going to work at all, I would have accidentally made it work by now.   SOLUTION:    None as of yet.       Clearly, when considering points #1 and #2 above, there is more happening on the ethernet side of the link than just ethernet. Something is different than a standard ethernet connection because this radio clearly caused major packet loss between the other devices plugged into am ethernet surge supressor. Maybe power is leaking through from the PowerShot device? And, its ability to completely bring a managed switch to its knees just reassures this.   === Rick Kosick StarLinX Internet Service