Hi,
yet another drive with [Subject] message...
Case label:
DTP110 1TB DC+5V=~1.0A 03/14
P/N: HDTP110HK3AA FAC: P C
S/N: 34CTxxxxxxxx
# update-smart-drivedb
/var/lib/smartmontools/drivedb/drivedb.h updated from trunk
# smartctl -a /dev/sdc
smartctl 6.4 2014-09-29 r3990 [i686-linux-3.16.0-00046-g68e0854] (local build)
Copyright (C) 2002-14, Bruce Allen, Christian Franke, www.smartmontools.org
/dev/sdc: Unknown USB bridge [0x0480:0xa00c (0x107)]
Please specify device type with the -d option.
Use smartctl -h to get a usage summary
# smartctl -d sat -s on -a /dev/sdc
smartctl 6.4 2014-09-29 r3990 [i686-linux-3.16.0-00046-g68e0854] (local build)
Copyright (C) 2002-14, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Toshiba 2.5" HDD MQ01ABD...
Device Model: TOSHIBA MQ01ABD100
Serial Number: 34CTxxxxx
LU WWN Device Id: 5 000039 561exxxxx
Firmware Version: AX001U
User Capacity: 1.000.204.886.016 bytes [1,00 TB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 5400 rpm
Form Factor: 2.5 inches
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS (minor revision not indicated)
SATA Version is: SATA 2.6, 3.0 Gb/s (current: 3.0 Gb/s)
Local Time is: Mon Nov 17 21:56:47 2014 CET
SMART support is: Available - device has SMART capability.
SMART support is: Disabled
=== START OF ENABLE/DISABLE COMMANDS SECTION ===
SMART Enabled.
=== START OF READ SMART DATA SECTION ===
SMART Status not supported: Incomplete response, ATA output registers missing
SMART overall-health self-assessment test result: PASSED
Warning: This result is based on an Attribute check.
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 120) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off
support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 242) minutes.
SCT capabilities: (0x003d) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED
WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000b 100 100 050 Pre-fail Always
- 0
2 Throughput_Performance 0x0005 100 100 050 Pre-fail Offline
- 0
3 Spin_Up_Time 0x0027 100 100 001 Pre-fail Always
- 2782
4 Start_Stop_Count 0x0032 100 100 000 Old_age Always
- 17
5 Reallocated_Sector_Ct 0x0033 100 100 050 Pre-fail Always
- 0
7 Seek_Error_Rate 0x000b 100 100 050 Pre-fail Always
- 0
8 Seek_Time_Performance 0x0005 100 100 050 Pre-fail Offline
- 0
9 Power_On_Hours 0x0032 100 100 000 Old_age Always
- 1
10 Spin_Retry_Count 0x0033 100 100 030 Pre-fail Always
- 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always
- 11
191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always
- 0
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always
- 1
193 Load_Cycle_Count 0x0032 100 100 000 Old_age Always
- 30
194 Temperature_Celsius 0x0022 100 100 000 Old_age Always
- 23 (Min/Max 19/30)
196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always
- 0
197 Current_Pending_Sector 0x0032 100 100 000 Old_age Always
- 0
198 Offline_Uncorrectable 0x0030 100 100 000 Old_age Offline
- 0
199 UDMA_CRC_Error_Count 0x0032 200 253 000 Old_age Always
- 0
220 Disk_Shift 0x0002 100 100 000 Old_age Always
- 0
222 Loaded_Hours 0x0032 100 100 000 Old_age Always
- 0
223 Load_Retry_Count 0x0032 100 100 000 Old_age Always
- 0
224 Load_Friction 0x0022 100 100 000 Old_age Always
- 0
226 Load-in_Time 0x0026 100 100 000 Old_age Always
- 263
240 Head_Flying_Hours 0x0001 100 100 001 Pre-fail Offline
- 0
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
No SMART attributes have any "unknown" description,
so from an implementation POV we seem to be fine here :-)
So, for automatic recognition purposes
this device appears to need a "-d sat" entry
added to the controller database, too.
I will soon proceed with adding an entry to Wiki Supported_USB-Devices...
Thanks,
Andreas Mohr
--
GNU/Linux. It's not the software that's free, it's you.
------------------------------------------------------------------------------
Download BIRT iHub F-Type - The Free Enterprise-Grade BIRT Server
from Actuate! Instantly Supercharge Your Business Reports and Dashboards
with Interactivity, Sharing, Native Excel Exports, App Integration & more
Get technology previously reserved for billion-dollar corporations, FREE
http://pubads.g.doubleclick.net/gampad/clk?id=157005751&iu=/4140/ostg.clktrk
_______________________________________________
Smartmontools-database mailing list
[email protected]
https://lists.sourceforge.net/lists/listinfo/smartmontools-database
