Having watched other people do it; I quickly jump to a conclusion which most
likely is wrong.
Two things happen in the creation of the leading edge. The leading edge was
created originally with sanding. A very long sanding device with a hard
back must be used to get a consistent surface and radius without concave
points. Similarly a tool like this must be used when finishing the glass
layer.
Typically we want the leading edge reinforced. Consequently we put extra
there. Suggested technique should work very well.
Now we are ready for the problems. On the sanding of the glass it is
typical to substitute pressure for course fast cutting sandpaper. With fine
sandpaper at this stage kit would not be uncommon to be pushing into the
glass. My suggestion will create horror in the eyes of most people . Use a
sixty grit paint remover grit of one of the better materials. In otherwords
flint just will not cut it. Make sure you go lightly . Keep the heat
down. It is very easy to create heat with fine paper and haste.
If the original long hard back was used to get a good contour before
covering then the clean up with the course afterwards should not take all
that long. If the original surface was rippled then you will cut through
no matter how you do it on the high spots.
Now we shall hear how others do it.
Rick
Date: Tue, 15 May 2001 11:17:17 -0700
From: "Marc Webster" <[EMAIL PROTECTED]>
To: [EMAIL PROTECTED]
Subject: vac bagging technique question?
Message-ID: <[EMAIL PROTECTED]>
Hello all,
With the demise of my addiction, I plan to bag another set of wings over the
memorial day holiday. I want to try something new and I thought I would run
it buy everyone to get some feedback before I bag my wing. I have bagged
many wings, and hate all of the sanding that is required of the leading
edge. I usually, cut my materials an inch or so larger than my mylars and
after I lay the core on the bottom mylar, I fold over the remaining material
over the leading edge and onto the top of the core. I then fold over my top
skin mylar and the extra inch of material attaches itself to the folded
material and continues forward to nothing. The problem with this is after I
cut off the flash, I need to sand my leading edge quite a bit to get the
proper shape back.
To alleviate this I was going to try a new technique, and I am sure someone
else out there does it this way and I could use some feedback.
What I want to try is this. Could I possibly attach a ribbon of glass along
the leading edge prior to bagging with a light coating of 3M 77. I could
mix a small batch of epoxy and wet out this ribbon, then set the wing halves
aside for say 30 minutes. after the 30 minutes has passed, I could start to
wet out my layup on the mylars. when this is done, I would trim the
material flush with the mylars. I could then lay my core in and fold over
the top skin. If the core was placed accurately enough, the mylars would
stop just short of the tip of the leading edge. When it came time to remove
from the bag, there would be a small ridge the full length of the leading
edge top and bottom where the mylar ended. This would be much easier to
sand smooth and my leading edge would be more accurate.
Does anyone out there do it this way. If so, any tips you could pass on.
Is there a better way? I am open to any and all suggestions.
Another problem I have run into is; after the occasional dork landing, my
wings swing forward and my root ribs tend to get pushed into the foam and
separate from the surface. I placed a dowel inside the fuselage to keep it
from cracking at the wing joint. The result of this is my fuselage does not
absorb any of the energy and my root ribs get pushed in. I may get rid of
the dowell altogether or replace it with an elastomer bushing as I would
rather replace fuselages than wings. I also may drill small holes all
around the root rib, this would allow epoxy to fill the holes and act as
rivets or nails between the skin and the root rib. Anyone else have this
problem? How did you fix it?
Thank you for your time,
Marc Webster
RCSE-List facilities provided by Model Airplane News. Send "subscribe" and
"unsubscribe" requests to [EMAIL PROTECTED]