I have some experience with attaching 3 layers of 1.5 oz glass strips to
shaped foam LE cores, before bagging. 

I start out with irregular lengths 3/4" wide strips, going next to 1-1/4"
and then to 1/3/4". These are sprayed with 3M77 and progressively attached
so as to minimize puckers, bumps, overlaps and gaps. This may involve
frequent repositioning. After these strips are down, they are wetted out by
brushing on a mix of the bagging epoxy.  The epoxy is pressed in well with
a plastic strip curled around and drawn along the LE.  

Prior to adding these strips the mylars are cut, waxed and painted. The
cloth layers have been cut and are marked to know where they go and in what
order. You want to size the cloth pieces so there is no Kevlar or CF on the
LE. Better to stop the larger piece of Kevlar or CF a bit behind the LE and
have extra layers of glass in their place to complete the layup. I
carefully shape the LE's of the carriers to extend very close to the LE of
the cores, but not meet. This is easily controlled by having excess carrier
along the fold line at the TE and knowing where you will be positioning the
core after the cloth is wetted out. This leaves a place for epoxy to escape
at the rear of the cores and leeway in trimming up the TE's forward of the
area where the fold is and which often has bad spots. I also wax the
outside of the carriers to avoid epoxy sticking to them there. After the
epoxy has been spread, any excess cloth beyond the carriers is scissored
off. The core is then carefully positioned. Thin tape is applied in a few
spots along the LE and all is placed in the bag, surrounded by thick,
textured Bounty towel. As the vacuum presses, the excess epoxy is picked up
by the Bounty so it does not congregate along the LE and require all that
sanding. Out of the bag, the Bounty can be peeled away quite easily and the
carriers opened. A long sanding tool is used to touch up the LE. It is
always work and pits may appear to be filled and resanded. Touch up
painting is needed which requires great care. New paint may not stick to
the old which has a wax film residue from bagging on it. New paint may eat
into the old and make a terrible mess. Dishwashing detergent can be used to
remove the wax. If tape is applied to mask for LE painting, it may lift old
paint. It is safer to just lay a balsa sheet down and fog over the edge to
paint the LE with the same or a contrasting color. Practice on something
else first. After doing your best to make a nice looking LE, remember that
you can use some reflective material on the front to strategically cover
areas you are not happy with. 

----------
> From: happl <[EMAIL PROTECTED]>
> To: soaring <[EMAIL PROTECTED]>; [EMAIL PROTECTED]
> Subject: [RCSE] vac bagging technique question?
> Date: Tuesday, May 15, 2001 6:12 PM
> 
> Having watched other people do it; I quickly jump to a conclusion which
most
> likely is wrong.
> 
> Two things happen in the creation of the leading edge.  The leading edge
was
> created originally with sanding.  A very long sanding device with a hard
> back must be used to get a consistent surface and radius without concave
> points.  Similarly a tool like this must be used when finishing the glass
> layer.
> 
> Typically we want the leading edge reinforced.  Consequently we put extra
> there.  Suggested technique should work very well.
> 
> Now we are ready for the problems.  On the sanding of the glass it is
> typical to substitute pressure for course fast cutting sandpaper.  With
fine
> sandpaper at this stage kit would not be uncommon to be pushing into the
> glass.  My suggestion will create horror in the eyes of most people . 
Use a
> sixty grit paint remover grit of one of the better materials.  In
otherwords
> flint just will not cut it.   Make sure you go lightly .  Keep the heat
> down.  It is very easy to create heat with fine paper and haste.
> 
> If the original long hard back was used to get a good contour before
> covering then the clean up with the course afterwards should not take all
> that long.  If  the original surface was rippled then you will cut
through
> no matter how you do it on the high spots.
> 
> Now we shall hear how others do it.
> 
> Rick
> 
> 
> 
> 
> Date: Tue, 15 May 2001 11:17:17 -0700
> From: "Marc Webster" <[EMAIL PROTECTED]>
> To: [EMAIL PROTECTED]
> Subject: vac bagging technique question?
> Message-ID: <[EMAIL PROTECTED]>
> 
> Hello all,
> 
> With the demise of my addiction, I plan to bag another set of wings over
the
> memorial day holiday.  I want to try something new and I thought I would
run
> it buy everyone to get some feedback before I bag my wing.  I have bagged
> many wings, and hate all of the sanding that is required of the leading
> edge.  I usually, cut my materials an inch or so larger than my mylars
and
> after I lay the core on the bottom mylar, I fold over the remaining
material
> over the leading edge and onto the top of the core.  I then fold over my
top
> skin mylar and the extra inch of material attaches itself to the folded
> material and continues forward to nothing.  The problem with this is
after I
> cut off the flash, I need to sand my leading edge quite a bit to get the
> proper shape back.
> 
> To alleviate this I was going to try a new technique, and I am sure
someone
> else out there does it this way and I could use some feedback.
> 
> What I want to try is this.  Could I possibly attach a ribbon of glass
along
> the leading edge prior to bagging with a light coating of 3M 77.  I could
> mix a small batch of epoxy and wet out this ribbon, then set the wing
halves
> aside for say 30 minutes.  after the 30 minutes has passed, I could start
to
> wet out my layup on the mylars.  when this is done, I would trim the
> material flush with the mylars.  I could then lay my core in and fold
over
> the top skin.  If the core was placed accurately enough, the mylars would
> stop just short of the tip of the leading edge.  When it came time to
remove
> from the bag, there would be a small ridge the full length of the leading
> edge top and bottom where the mylar ended.  This would be much easier to
> sand smooth and my leading edge would be more accurate.
> 
> Does anyone out there do it this way.  If so, any tips you could pass on.
> Is there a better way?  I am open to any and all suggestions.
> 
> Another problem I have run into is; after the occasional dork landing, my
> wings swing forward and my root ribs tend to get pushed into the foam and
> separate from the surface.  I placed a dowel inside the fuselage to keep
it
> from cracking at the wing joint.  The result of this is my fuselage does
not
> absorb any of the energy and my root ribs get pushed in.  I may get rid
of
> the dowell altogether or replace it with an elastomer bushing as I would
> rather replace fuselages than wings.  I also may drill small holes all
> around the root rib, this would allow epoxy to fill the holes and act as
> rivets or nails between the skin and the root rib.  Anyone else have this
> problem?  How did you fix it?
> 
> Thank you for your time,
> 
> Marc Webster
> 
> RCSE-List facilities provided by Model Airplane News.  Send "subscribe"
and "unsubscribe" requests to [EMAIL PROTECTED]

RCSE-List facilities provided by Model Airplane News.  Send "subscribe" and 
"unsubscribe" requests to [EMAIL PROTECTED]

Reply via email to