I am not versed on TD planes, but it has always been my understanding
that any plane with a given airfoil has an optimum wing loading at which
it will fly best based in large part to the airfoil used. Now granted
"best" is a poor choice of words, perhaps efficiently is more accurate?

 In any regards, I would think lightness for lightness sake is a fools
mission, and in TD events it would seem to me your sailplanes weight
(mass) has it's largest influence with dork or spot landings whereas low
mass carbon reinforced light planes have the potential to sustain less
damage than heavy ships with greater inertia.  

I know in large scale soaring weight usually translates into energy, and
flying performance, up to a point, will increase up to the magic wing
loading number. With a 33% scale ship that could easily be up to 37
pounds!
TD guys are always amazed when they fly their first 5-6 meter ship and
the light bulb goes off.
Maybe or maybe not germane to your question...


JD

Endless Mountain Models
http://www.scalesoaring.com
email: [EMAIL PROTECTED]
 

-----Original Message-----
From: George Voss [mailto:[EMAIL PROTECTED] 
Sent: Sunday, July 11, 2004 5:26 PM
To: RCSE E-mail
Subject: [RCSE] Is it worth it?

Put on your thinking caps and let me know what you think.

The question is: How much weight loss is necessary to notice a
difference in
flying/landing capability?  The plane is question is an unlimited size
plane
with about 8 sq.ft. of wing (1151 sq.in.), weighs in at about 78 ounces
and
has a long tail moment.  The plane is flown in normally mild wind
conditions, but rarely in calm conditions.  It's flown in AMA style
contests
only, no F3X anything.  Average winds are typically 5-12mph.  The plane
has
ballast capabilities.

I weighed the molded stabs against a custom made "light" set of stabs
and I
can lose 4g if I change out the stabs.  Total weight savings at a 4:1
tail
moment ratio would be 16g or slightly over 1/2 an ounce. The rudder is
also
molded but I'm not going to pull it off to weigh it.  I'll guess I can
save
3g with a new light one so now we have a 7g savings in the tail and a
1-ounce loss in overall weight.

The only other thing I could change is the pushrod system, which weighs
a
little over an ounce according to the CST web site.  Since 90% is behind
the
CG, we'll call it one ounce.  If I leave the stab and rudder alone, I'll
lose roughly 4 ounces total weight.  If I include the stab and rudder
I'll
lose roughly 5 ounces total.  My guess is keeping the molded stab is a
good
idea strength wise.

The question then is: Is a 4-ounce weight loss, which equal 1/2 ounce
per
square foot, worth the trouble?  Making the rudder pull-pull will be an
evenings worth of work.  If we use the correct materials, the actuation
system is proven safe and weighs virtually nothing.  Is 1/2 an ounce of
wing
loading worth the trouble?

For the engineers, how do you calculate the weight of a pushrod in
inch/ounces over its total length?  Or asked another way, since the
pushrod
weighs in at slightly over an ounce and 90% of it is behind the CG, is 1
ounce times 0.9 going to give me the correct answer?  If I put the
pushrod
on 2 scales, one at each end of the rod, each would show 1/2 of the
total
weight.  So how much of this total 1 ounce weight can I calculate at the
rudder hookup?

gv

RCSE-List facilities provided by Model Airplane News.  Send "subscribe"
and "unsubscribe" requests to [EMAIL PROTECTED]  Please note
that subscribe and unsubscribe messages must be sent in text only format
with MIME turned off.

RCSE-List facilities provided by Model Airplane News.  Send "subscribe" and 
"unsubscribe" requests to [EMAIL PROTECTED]  Please note that subscribe and 
unsubscribe messages must be sent in text only format with MIME turned off.

Reply via email to