Hi, thanks to you all I have got the Speedtouch operational with the kernel module.
This incorporated the following steps: - install kernel-source rpm - apply patches of Duncan for usb - configure the kernel to include ATM, PPP Over ATM support, Speedtouch (and RFC1483/2684 Bridged Protocols, but I doubt if that is required for pppoatm) - Âmake and Âmake modules_install install for the kernel - add new kernel to grub.conf - use speedbundle-1.0, where the kernel-module part is not built/ installed. Then I see still some errors/warnings during boot, but the modem is operational (I sent this mail via FC2 using the kernel module). See the part of /var/log/messages related to the ST330: May 27 07:18:12 localhost kernel: USB Universal Host Controller Interface driver v2.2 May 27 07:18:13 localhost kernel: uhci_hcd 0000:00:04.2: UHCI Host Controller May 27 07:18:13 localhost kernel: uhci_hcd 0000:00:04.2: irq 9, io base 0000d400 May 27 07:18:13 localhost kernel: uhci_hcd 0000:00:04.2: new USB bus registered, assigned bus number 1 May 27 07:18:13 localhost kernel: hub 1-0:1.0: USB hub found May 27 07:18:13 localhost kernel: hub 1-0:1.0: 2 ports detected May 27 07:18:13 localhost kernel: uhci_hcd 0000:00:04.3: UHCI Host Controller May 27 07:18:13 localhost kernel: uhci_hcd 0000:00:04.3: irq 9, io base 0000d000 May 27 07:18:13 localhost kernel: uhci_hcd 0000:00:04.3: new USB bus registered, assigned bus number 2 May 27 07:18:13 localhost kernel: hub 2-0:1.0: USB hub found May 27 07:18:13 localhost kernel: hub 2-0:1.0: 2 ports detected May 27 07:18:13 localhost kernel: usb 1-2: new full speed USB device using address 2 May 27 07:18:13 localhost kernel: hub 1-2:1.0: USB hub found May 27 07:18:13 localhost kernel: device-mapper: 4.1.0-ioctl (2003-12-10) initialised: [EMAIL PROTECTED] May 27 07:18:13 localhost kernel: usb 1-2: control timeout on ep0in May 27 07:18:13 localhost kernel: hub 1-2:1.0: config failed, can't read hub descriptor (err -110) May 27 07:18:13 localhost kernel: usb 2-2: new full speed USB device using address 2 May 27 07:18:13 localhost kernel: hub 2-2:1.0: USB hub found May 27 07:18:13 localhost kernel: hub 2-2:1.0: 4 ports detected May 27 07:18:13 localhost kernel: usb 2-2.2: new full speed USB device using address 3 May 27 07:18:13 localhost kernel: usbcore: registered new driver speedtch May 27 07:18:13 localhost kernel: usb 2-2.2: usbfs: interface 1 claimed while 'modem_run' sets config #1 May 27 07:18:13 localhost kernel: usb 2-2.2: usbfs: interface 2 claimed while 'modem_run' sets config #1 May 27 07:18:13 localhost kernel: usb 2-2.2: bulk timeout on ep5in May 27 07:18:13 localhost kernel: usbfs: USBDEVFS_BULK failed dev 3 ep 0x85 len 512 ret -110 May 27 07:18:13 localhost kernel: usb 2-2.2: usbfs: interface 0 claimed while 'modem_run' sets config #1 May 27 07:18:13 localhost kernel: usb 2-2.2: usbfs: interface 1 claimed while 'modem_run' sets config #1 May 27 07:18:13 localhost kernel: usb 2-2.2: usbfs: interface 2 claimed while 'modem_run' sets config #1 May 27 07:18:22 localhost kernel: usbfs: process 1627 (modem_run) did not claim interface 0 before use May 27 07:18:28 localhost pppd[2533]: Plugin pppoatm.so loaded. May 27 07:18:28 localhost kernel: CSLIP: code copyright 1989 Regents of the University of California May 27 07:18:28 localhost pppd[2533]: PPPoATM plugin_init May 27 07:18:28 localhost pppd[2533]: PPPoATM setdevname - remove unwanted options May 27 07:18:28 localhost kernel: PPP generic driver version 2.4.2 May 27 07:18:28 localhost pppd[2533]: PPPoATM setdevname_pppoatm - SUCCESS:8.48 May 27 07:18:28 localhost pppd[2533]: pppd 2.4.2b3 started by root, uid 0 May 27 07:18:28 localhost pppd[2533]: Using interface ppp0 May 27 07:18:28 localhost pppd[2533]: Connect: ppp0 <--> 8.48 May 27 07:18:31 localhost pppd[2533]: PAP authentication succeeded May 27 07:18:31 localhost pppd[2533]: local IP address xx.xx.xxx.xxx May 27 07:18:31 localhost pppd[2533]: remote IP address xxx.xxx.xxx.xxx May 27 07:18:31 localhost pppd[2533]: primary DNS address xx.xx.xx.x May 27 07:18:31 localhost pppd[2533]: secondary DNS address xx.xx.xx.x Duncan, you told that most of them are due to modem_run.c and are not critical, but the ÂdonÂt look good messages as you called them are still there: May 27 07:18:13 localhost kernel: usb 1-2: control timeout on ep0in May 27 07:18:13 localhost kernel: hub 1-2:1.0: config failed, can't read hub descriptor (err -110) Everything operates however properly. Thanks all for the support! I will give feedback to Eric Brasseur who already has a webpages online with solutions for the Speedtouch 330 on FC1 (kernel space) and FC2 (user space). Regards, Aad Liste de diffusion modem ALCATEL SpeedTouch USB Pour se désinscrire : mailto:[EMAIL PROTECTED]
