Tony,
  That is how I got started in all this as well. I still try to work on
the Cheap, but I did get a small Taig lathe for a combined birthday and
fathers day gift. I haven't gotten too far on it yet, but it is fun!

The smallest wobbler I have ever seen was in the front of a brass
engine, in 'HO' scale! The tender held the butane and the burner, the
engine was a little boiler, and in the smoke box was a tiny wobler
spinning a flywheel that linked to the worm gear for the locomotive! It
was great!!

I have also enjoyed what you have written and would like to try building
an enclosed tram... Once I've finished laying track and all the other
projects I have pending!

Thanks,
Terry Griner
387-0902 
 

-----Original Message-----
From: [EMAIL PROTECTED]
[mailto:[EMAIL PROTECTED] On Behalf Of Tony
Sent: Monday, November 07, 2005 11:45 AM
To: [email protected]
Subject: [SSLiveSteam] More Wobbler Food For Thought

Hi Steve...and wobbler fans...

Wobblers are neat in that for a folk like me I can make a steam engine
for little money and without a lathe...well sort of without a lathe!!!

Most of my wobblers I make from K&S brass tube...it is allready round
and has a hole down the middle!

Not making light of having a proper lathe...I would love to have one!

The pistons that I make up are of 3/8" or 1/2"  brass rodding that I
found scrap some where...a couple of feet of it has lasted me 20 years
of building with lots left for another 20 years if I can be so lucky. I
made one tiny wobbler single acting from 3/16" brass rod...drilled and
lapped on my verticle table drill...sort of a poor mans lathe.

My modeling budjet or lack of one has put me on a path of doing things
on the cheap...finding old Mamod cylinders fo me is like finding gold.
Lots of folks have upgraded to IP and I have been able to accquire the
Mamod discards. Mamod cylinders are quite well thought out... Inside is
a very smart piece of engineering...not like the early Mamod stationary
engines with a solid piston...and if you were lucky a grove had been
machined in it to act like a seal.

Most early Mamod stationary engines with their low pressure boilers
(12lbs) relied on the fact that their was lots of condesed water in the
steam...the water would get into the grove and help with cylinder
sealing...in fact putting nice dry steam into them made them run worse.

The Mamod piston is spring loaded on it's rod...with a couple of little
seals front and back...this lets the piston "float" in the cylinder and
self center...rather cool when you want to mass produce a prescion
assembly without having to lap etc...

A fairly new producer of steam motors have taken the lowly wobbler to
new levels...Chedder aside... the new wobblers from SVS are little
jewels. I am attaching a couple of pictures of the steam motor and a
small tram "Lucy" that I was commissioned to make. The SVS is TINY...the
whole motor with reduction drive fits into a 30 by 40mm cube...another
commission I am working on will use one in an "O" 
scale 2P british outline live steam...the boiler will be gas/butane
fired internal Belpar with a grate suitable for real coal...90% of the
heat will be from the Butane...the coal will provide a little of the
heat but 100% of real coal smoke...sort of cheating but a scale "O"
scale fire box is only 20 by 30mm...with a fire box door about as big
around as your thumb!

A single acting wobbler with a decent flywheel will pull a 20LB train
that I mentioned in another eMail...because the cylinder is single
acting and because there is only the ONE cylinder the motor it uses
1/4 the amount of a steam motor that has TWO double acting IP
cylinders...!

There is another wonderful thing that a single acting wobbler can do
that a slide valve cylinder can't! ...at least in the model sizes that
we deal with as in Roundhouse/Accucraft etc ...is that when a wobbler
cylinder runs fast you start to get steam cut off...'cause the cylinder
cannot fill fully on its power stroke...that is the cylinder is moving
accross the port so quicly that there is not enough time for it to fill
properly ...neat huh!

This takes us into a whole new realm of wobblers that is the size of the
steam inlet port and it's shape...for those who have not fallen to sleep
by now...ya I really like wobblers cause you can do a lot of
experimentation with them that you can't withe slide valve.

I have tried different hole sizes and shapes and get wonderful
results...I can tailor the steam motor to the expected power and speed
of the finished model. Besides the inlet and outlet sizes the timing of
wobblers can drastically change the power and speed of them to...that is
the spacing of the steam ports in the block have a major impact into the
speed of the motor...just like timing an electric motor by changing the
position of the comutator...these steam motors can be timmed...

Thats enough for tonight a lot to take in...I hope along the line some
one will get some help for their sick wobblers...

...Steve we will get there...lots to try yet...Tony
_______________________________________________
SSLiveSteam mailing list
Send messages: [email protected] Cancel subscription:
http://postfix.45mm.com/mailman/listinfo/sslivesteam
Rules: http://www.45mm.com/sslivesteam_guide.html


"This e-mail is intended for the sole use of the intended recipient and may 
contain privileged, sensitive, or protected health information. If you are 
not the intended recipient, be advised that the unauthorized use, disclosure, 
copying, distribution, or action taken in reliance on the contents of this
communication is prohibited. If you have received this e-mail in error, 
please notify the sender via telephone or return e-mail and immediately
delete this e-mail."

_______________________________________________
SSLiveSteam mailing list
Send messages: [email protected]
Cancel subscription: http://postfix.45mm.com/mailman/listinfo/sslivesteam
Rules: http://www.45mm.com/sslivesteam_guide.html

Reply via email to