Re: [Elphel-support] Elphel NC353L No HDD found

Tue, 30 Jul 2013 00:51:30 -0700

Hello Oleg,

On the USB port there is not even 5V so is cannot work. We have already upgraded to the latest firmeware (2011).
Thanks for your help.

Patrick

Gesendet: Montag, 29. Juli 2013 um 21:31 Uhr
Von: Oleg <support-list@support.elphel.com>
An: "Patrick Eisenkeil" <patethek...@gmx.net>
Cc: "elphel support-list" <support-list@support.elphel.com>
Betreff: Re: [Elphel-support] Elphel NC353L No HDD found
Patrick,

I think the interface board (10369) needs to be replaced.

You could still try:
1. Check the serial port output  if you have the cable.
2. Check if USB works - plug in some thumb drive and get the "dmesg" output.
3. Update the camera's firmware:
With the liveusb 
or without:
a. setup an nfs share.
b. copy firmware image files into /nfs/latest80/
c. go to http://cam-ip -> system preferences -> firmware -> check nfs -> validate... -> Reflash

Best regards,
Oleg Dzhimiev
Electronics Engineer
phone: +1 801 783 5555 x124
Elphel, Inc.

On 29 July 2013 00:14, Patrick Eisenkeil <patethek...@gmx.net> wrote:
This is the output from the dmesg:
Linux version 2.6.19 (andrey@inspiron) (gcc version 3.2.1 Axis release R64/1.64) #74 Tue Sep 6 13:08:44 MDT 2011
Setting up paging and the MMU.
On node 0 totalpages: 8192
  DMA zone: 32 pages used for memmap
  DMA zone: 0 pages reserved
  DMA zone: 8160 pages, LIFO batch:0
  Normal zone: 0 pages used for memmap
Linux/CRISv32 port on ETRAX FS (C) 2003, 2004 Axis Communications AB
Built 1 zonelists.  Total pages: 8160
Kernel command line: root=/dev/mtdblock3 init=/linuxrc rootfstype=jffs2
PID hash table entries: 256 (order: 8, 1024 bytes)
Dentry cache hash table entries: 8192 (order: 2, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 1, 16384 bytes)
Memory: 40320k/65536k available (1744k kernel code, 25216k reserved, 606k data, 72k init)
Calibrating delay loop... 199.47 BogoMIPS (lpj=997376)
Mount-cache hash table entries: 1024
NET: Registered protocol family 16
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
NET: Registered protocol family 2
IP route cache hash table entries: 512 (order: -2, 2048 bytes)
TCP established hash table entries: 2048 (order: 0, 8192 bytes)
TCP bind hash table entries: 1024 (order: -1, 4096 bytes)
TCP: Hash tables configured (established 2048 bind 1024)
TCP reno registered
Check hardware configuration of Elphel 353 camera
Elphel 10349/10369 IO extension board is present
fast_timer_init()
JFFS2 version 2.2. (NAND) (C) 2001-2006 Red Hat, Inc.
io scheduler noop registered (default)
Serial: CRISv32 driver $Revision: 1.78 $ <6>ttyS0 at I/O 0xb0026000 (irq = 68) is a CRISv32
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
PPP generic driver version 2.4.2
ETRAX FS 10/100MBit ethernet v0.01 (c) 2003 Axis Communications AB
eth0: changed MAC to 00:40:8C:CD:00:00
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 50MHz system bus speed for PIO modes; override with idebus=xx
ide: ETRAX FS built-in ATA DMA controller
cris_ide_init()
Probing IDE interface ide0...
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver usbserial
drivers/usb/serial/usb-serial.c: USB Serial support registered for generic
usbcore: registered new interface driver usbserial_generic
drivers/usb/serial/usb-serial.c: USB Serial Driver core
drivers/usb/serial/usb-serial.c: USB Serial support registered for Belkin / Peracom / GoHubs USB Serial Adapter
usbcore: registered new interface driver belkin
drivers/usb/serial/belkin_sa.c: USB Belkin Serial converter driver v1.2
drivers/usb/serial/usb-serial.c: USB Serial support registered for cp2101
usbcore: registered new interface driver cp2101
drivers/usb/serial/cp2101.c: Silicon Labs CP2101/CP2102 RS232 serial adaptor driver v0.07
drivers/usb/serial/usb-serial.c: USB Serial support registered for Garmin GPS usb/tty
usbcore: registered new interface driver garmin_gps
drivers/usb/serial/garmin_gps.c: garmin gps driver v0.28
drivers/usb/serial/usb-serial.c: USB Serial support registered for MCT U232
usbcore: registered new interface driver mct_u232
drivers/usb/serial/mct_u232.c: Magic Control Technology USB-RS232 converter driver z2.0
drivers/usb/serial/usb-serial.c: USB Serial support registered for pl2303
usbcore: registered new interface driver pl2303
drivers/usb/serial/pl2303.c: Prolific PL2303 USB to serial adaptor driver
ETRAX FS stream co-processor driver v0.01, (c) 2003 Axis Communications AB
stream co-processor: init done.
axisflashmap: ...
NAND device: Manufacturer ID: 0x20, Chip ID: 0xf1 (ST Micro NAND 128MiB 3,3V 8-bit)
Additional Info: ID byte3=0x80, byte4=0x1d
Bad block table found at page 65472, version 0x01
Bad block table found at page 65408, version 0x01
Flash is rated 30 ns, modifying bif_core_rw_grp3: old=0x6300483, new=0x6300001
NAND 128MiB 3,3V 8-bit: 0x08000000 bytes of NAND flash memory.
axisflashmap: Set to boot from NAND flash, making NAND flash primary device.
axisflashmap: flash read 512 bytes at 0x00040000, data: 00 b0 05 f0 25 ff ed 9c
axisflashmap: partition table offset 10, data: ef be 84 00 2a 0f 00 00
axisflashmap: Found a valid partition table at 0xc02fd9ae-0xc02fda3a.
offset == 0x00040000, size == 0x007C0000
offset == 0x00800000, size == 0x01800000
offset == 0x02000000, size == 0x05000000
offset == 0x07000000, size == 0x00C00000
Creating 1 MTD partitions on "NAND 128MiB 3,3V 8-bit":
0x00000000-0x08000000 : "main"
Creating 1 MTD partitions on "NAND 128MiB 3,3V 8-bit":
0x00000000-0x00040000 : "part0"
Creating 1 MTD partitions on "NAND 128MiB 3,3V 8-bit":
0x00040000-0x00800000 : "part1"
Creating 1 MTD partitions on "NAND 128MiB 3,3V 8-bit":
0x00800000-0x02000000 : "part2"
Creating 1 MTD partitions on "NAND 128MiB 3,3V 8-bit":
0x02000000-0x07000000 : "part3"
Creating 1 MTD partitions on "NAND 128MiB 3,3V 8-bit":
0x07000000-0x07c00000 : "part4"
ETRAX FS GPIO driver v2.5, (c) 2003-2006 Axis Communications AB
Elphel (R) model 353 FPGA (Xilinx (R) XC3S1200E) configuration driver - 132
Elphel (R) model 353 system clocks (PLL frequency synth.) driver - 133
fpga_control- 129
arch/cris/arch-v32/drivers/elphel/framepars.c:387:initGlobalPars GLOBALPARS(G_DEBUG)=0
arch/cris/arch-v32/drivers/elphel/framepars.c:417:initMultiPars GLOBALPARS(G_MULTI_NUM)=0
Elphel (R) Model 353 Frame Parameters device driver - 130
Elphel FPGA interrupts initialized
Initializing DMA registers for EXTDMA3 - Elphel (R) Model 353 Camera Driver - 126
Elphel (R) model 353 i2c character device driver - 134, 2 channels
Raw image access driver- 131
Elphel (R) Model 353 video buffer device driver- 135
Elphel (R) model 353 Exif device driver - 125
Starting Elphel (R) Model 353 Gamma Tables device driver - 137
Elphel (R) Model 353 Gamma Tables device driver - 137
Elphel (R) Model 353 Histograms device driver
imu_logger- 141
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
VFS: Mounted root (jffs2 filesystem) readonly.
Freeing unused kernel memory: 72k freed
Empty flash at 0x00b54c14 ends at 0x00b55000
[root@Elphel353 /root]769# dmesg
Linux version 2.6.19 (andrey@inspiron) (gcc version 3.2.1 Axis release R64/1.64) #74 Tue Sep 6 13:08:44 MDT 2011
Setting up paging and the MMU.
On node 0 totalpages: 8192
  DMA zone: 32 pages used for memmap
  DMA zone: 0 pages reserved
  DMA zone: 8160 pages, LIFO batch:0
  Normal zone: 0 pages used for memmap
Linux/CRISv32 port on ETRAX FS (C) 2003, 2004 Axis Communications AB
Built 1 zonelists.  Total pages: 8160
Kernel command line: root=/dev/mtdblock3 init=/linuxrc rootfstype=jffs2
PID hash table entries: 256 (order: 8, 1024 bytes)
Dentry cache hash table entries: 8192 (order: 2, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 1, 16384 bytes)
Memory: 40320k/65536k available (1744k kernel code, 25216k reserved, 606k data, 72k init)
Calibrating delay loop... 199.47 BogoMIPS (lpj=997376)
Mount-cache hash table entries: 1024
NET: Registered protocol family 16
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
NET: Registered protocol family 2
IP route cache hash table entries: 512 (order: -2, 2048 bytes)
TCP established hash table entries: 2048 (order: 0, 8192 bytes)
TCP bind hash table entries: 1024 (order: -1, 4096 bytes)
TCP: Hash tables configured (established 2048 bind 1024)
TCP reno registered
Check hardware configuration of Elphel 353 camera
Elphel 10349/10369 IO extension board is present
fast_timer_init()
JFFS2 version 2.2. (NAND) (C) 2001-2006 Red Hat, Inc.
io scheduler noop registered (default)
Serial: CRISv32 driver $Revision: 1.78 $ <6>ttyS0 at I/O 0xb0026000 (irq = 68) is a CRISv32
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
PPP generic driver version 2.4.2
ETRAX FS 10/100MBit ethernet v0.01 (c) 2003 Axis Communications AB
eth0: changed MAC to 00:40:8C:CD:00:00
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 50MHz system bus speed for PIO modes; override with idebus=xx
ide: ETRAX FS built-in ATA DMA controller
cris_ide_init()
Probing IDE interface ide0...
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver usbserial
drivers/usb/serial/usb-serial.c: USB Serial support registered for generic
usbcore: registered new interface driver usbserial_generic
drivers/usb/serial/usb-serial.c: USB Serial Driver core
drivers/usb/serial/usb-serial.c: USB Serial support registered for Belkin / Peracom / GoHubs USB Serial Adapter
usbcore: registered new interface driver belkin
drivers/usb/serial/belkin_sa.c: USB Belkin Serial converter driver v1.2
drivers/usb/serial/usb-serial.c: USB Serial support registered for cp2101
usbcore: registered new interface driver cp2101
drivers/usb/serial/cp2101.c: Silicon Labs CP2101/CP2102 RS232 serial adaptor driver v0.07
drivers/usb/serial/usb-serial.c: USB Serial support registered for Garmin GPS usb/tty
usbcore: registered new interface driver garmin_gps
drivers/usb/serial/garmin_gps.c: garmin gps driver v0.28
drivers/usb/serial/usb-serial.c: USB Serial support registered for MCT U232
usbcore: registered new interface driver mct_u232
drivers/usb/serial/mct_u232.c: Magic Control Technology USB-RS232 converter driver z2.0
drivers/usb/serial/usb-serial.c: USB Serial support registered for pl2303
usbcore: registered new interface driver pl2303
drivers/usb/serial/pl2303.c: Prolific PL2303 USB to serial adaptor driver
ETRAX FS stream co-processor driver v0.01, (c) 2003 Axis Communications AB
stream co-processor: init done.
axisflashmap: ...
NAND device: Manufacturer ID: 0x20, Chip ID: 0xf1 (ST Micro NAND 128MiB 3,3V 8-bit)
Additional Info: ID byte3=0x80, byte4=0x1d
Bad block table found at page 65472, version 0x01
Bad block table found at page 65408, version 0x01
Flash is rated 30 ns, modifying bif_core_rw_grp3: old=0x6300483, new=0x6300001
NAND 128MiB 3,3V 8-bit: 0x08000000 bytes of NAND flash memory.
axisflashmap: Set to boot from NAND flash, making NAND flash primary device.
axisflashmap: flash read 512 bytes at 0x00040000, data: 00 b0 05 f0 25 ff ed 9c
axisflashmap: partition table offset 10, data: ef be 84 00 2a 0f 00 00
axisflashmap: Found a valid partition table at 0xc02fd9ae-0xc02fda3a.
offset == 0x00040000, size == 0x007C0000
offset == 0x00800000, size == 0x01800000
offset == 0x02000000, size == 0x05000000
offset == 0x07000000, size == 0x00C00000
Creating 1 MTD partitions on "NAND 128MiB 3,3V 8-bit":
0x00000000-0x08000000 : "main"
Creating 1 MTD partitions on "NAND 128MiB 3,3V 8-bit":
0x00000000-0x00040000 : "part0"
Creating 1 MTD partitions on "NAND 128MiB 3,3V 8-bit":
0x00040000-0x00800000 : "part1"
Creating 1 MTD partitions on "NAND 128MiB 3,3V 8-bit":
0x00800000-0x02000000 : "part2"
Creating 1 MTD partitions on "NAND 128MiB 3,3V 8-bit":
0x02000000-0x07000000 : "part3"
Creating 1 MTD partitions on "NAND 128MiB 3,3V 8-bit":
0x07000000-0x07c00000 : "part4"
ETRAX FS GPIO driver v2.5, (c) 2003-2006 Axis Communications AB
Elphel (R) model 353 FPGA (Xilinx (R) XC3S1200E) configuration driver - 132
Elphel (R) model 353 system clocks (PLL frequency synth.) driver - 133
fpga_control- 129
arch/cris/arch-v32/drivers/elphel/framepars.c:387:initGlobalPars GLOBALPARS(G_DEBUG)=0
arch/cris/arch-v32/drivers/elphel/framepars.c:417:initMultiPars GLOBALPARS(G_MULTI_NUM)=0
Elphel (R) Model 353 Frame Parameters device driver - 130
Elphel FPGA interrupts initialized
Initializing DMA registers for EXTDMA3 - Elphel (R) Model 353 Camera Driver - 126
Elphel (R) model 353 i2c character device driver - 134, 2 channels
Raw image access driver- 131
Elphel (R) Model 353 video buffer device driver- 135
Elphel (R) model 353 Exif device driver - 125
Starting Elphel (R) Model 353 Gamma Tables device driver - 137
Elphel (R) Model 353 Gamma Tables device driver - 137
Elphel (R) Model 353 Histograms device driver
imu_logger- 141
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
VFS: Mounted root (jffs2 filesystem) readonly.
Freeing unused kernel memory: 72k freed
Empty flash at 0x00b54c14 ends at 0x00b55000
Empty flash at 0x02ae50f8 ends at 0x02ae5800
Empty flash at 0x02aedf3c ends at 0x02aee000
Empty flash at 0x042b2964 ends at 0x042b3000
Empty flash at 0x0442c4e4 ends at 0x0442c800
Empty flash at 0x047a68cc ends at 0x047a7000
eth0: changed MAC to 00:0E:64:08:18:EC
eth0: changed MAC to 00:0E:64:08:18:EC
arch/cris/arch-v32/drivers/elphel/framepars.c:387:initGlobalPars GLOBALPARS(G_DEBUG)=0
initSequencers:resetting both sequencers
arch/cris/arch-v32/drivers/elphel/framepars.c:417:initMultiPars GLOBALPARS(G_MULTI_NUM)=0
sensor clock set to 20000000
removing MRST from the sensor
Found MT9P001 2592x1944 sensor, chip ID=1801
trying MT9P001
Resetting MT9X001 sensor
Reading sensor registers to the shadows:
Initializing MT9X001 registers with default values:
Starting hardware sequencers
arch/cris/arch-v32/drivers/elphel/quantization_tables.c:211:init_qtable_head_cache
 
And my Sereal Number is: 00:0E:64:08:18:EC
 
 
 
Patrick
 
Gesendet: Sonntag, 28. Juli 2013 um 23:07 Uhr
Von: Oleg <support-list@support.elphel.com>
An: "Patrick Eisenkeil" <patethek...@gmx.net>
Cc: "elphel support-list" <support-list@support.elphel.com>
Betreff: Re: [Elphel-support] Elphel NC353L No HDD found
Hi,
 
What does "dmesg" display if you telnet to the camera? Please, send the output.
Also, what's the serial number? It's shown on the camera's front page.

Oleg
 
On 27 July 2013 07:29, Patrick Eisenkeil <patethek...@gmx.net> wrote:
I power it with a separate power Source  and it is The Same power Source on The PC 
What Setup do you mean?

Thanks for your help so far
 
Patrick

Am 26.07.2013 um 19:01 schrieb Oleg <support-list@support.elphel.com>:
 
Patrick,
 
What's the power source for the HDD when connected to the camera? the same PC? A picture of your setup might be of help.

Best regards,
Oleg Dzhimiev
Electronics Engineer
phone: +1 801 783 5555 x124
Elphel, Inc.
 
On 26 July 2013 01:38, Patrick Eisenkeil <patethek...@gmx.net> wrote:
Yes The Hdd Works perfectly on The PCs 

Von meinem iPhone gesendet

Am 26.07.2013 um 09:26 schrieb Oleg <support-list@support.elphel.com>:
 
Hi Patrick,

How do you power the HDD? Is it detected when connected to a PC?

Best regards,
Oleg Dzhimiev
Electronics Engineer
phone: +1 801 783 5555 x124
Elphel, Inc.
 
On 25 July 2013 23:26, Patrick Eisenkeil <patethek...@gmx.net> wrote:
I am using an Elphel NC353L.
I tried to connect the HDD via Sata and tired this: http://wiki.elphel.com/index.php?title=HDD_Format
But Step 2 does not show the right result, the camera does not find the HDD
If someone have an idea pleas give me any advice you have

_______________________________________________
Support-list mailing list
Support-list@support.elphel.com
http://support.elphel.com/mailman/listinfo/support-list_support.elphel.com

_______________________________________________
Support-list mailing list
Support-list@support.elphel.com
http://support.elphel.com/mailman/listinfo/support-list_support.elphel.com

_______________________________________________
Support-list mailing list
Support-list@support.elphel.com
http://support.elphel.com/mailman/listinfo/support-list_support.elphel.com

_______________________________________________
Support-list mailing list
Support-list@support.elphel.com
http://support.elphel.com/mailman/listinfo/support-list_support.elphel.com

_______________________________________________
Support-list mailing list
Support-list@support.elphel.com
http://support.elphel.com/mailman/listinfo/support-list_support.elphel.com

Reply via email to