I tried compiling support for ZIP+ external drive into my kernel 2.2.2
with the following on bootup ?

<4>imm: Version 2.03 (for Linux 2.0.0)
<4>imm: parport reports no devices.

It was connected with a disk in it.

I have a SCSI system with the following :

<4>scsi0 : Adaptec AHA274x/284x/294x (EISA/VLB/PCI-Fast SCSI) 5.1.10/3.2.4
<4>       <Adaptec AHA-294X Ultra SCSI host adapter>
<4>scsi : 1 host.
<4>  Vendor: SEAGATE   Model: ST15150W          Rev: 0023
<4>  Type:   Direct-Access                      ANSI SCSI revision: 02
<4>Detected scsi disk sda at scsi0, channel 0, id 0, lun 0
<4>  Vendor: SEAGATE   Model: ST15150N          Rev: 0023
<4>  Type:   Direct-Access                      ANSI SCSI revision: 02
<4>Detected scsi disk sdb at scsi0, channel 0, id 1, lun 0
<4>  Vendor: SEAGATE   Model: ST15230W SUN4.2G  Rev: 0738
<4>  Type:   Direct-Access                      ANSI SCSI revision: 02
<4>Detected scsi disk sdc at scsi0, channel 0, id 2, lun 0
<4>  Vendor: PLEXTOR   Model: CD-ROM PX-20TS    Rev: 1.01
<4>  Type:   CD-ROM                             ANSI SCSI revision: 02
<4>Detected scsi CD-ROM sr0 at scsi0, channel 0, id 3, lun 0
<4>  Vendor: HP        Model: T4000s            Rev: 1.10
<4>  Type:   Sequential-Access                  ANSI SCSI revision: 02
<4>Detected scsi tape st0 at scsi0, channel 0, id 4, lun 0
<4>  Vendor: YAMAHA    Model: CDR400t           Rev: 1.0d
<4>  Type:   CD-ROM                             ANSI SCSI revision: 02
<4>Detected scsi CD-ROM sr1 at scsi0, channel 0, id 6, lun 0
<4>scsi : detected 1 SCSI tape 2 SCSI cdroms 3 SCSI disks total.
<6>(scsi0:0:3:0) Synchronous at 10.0 Mbyte/sec, offset 15.
<6>Uniform CDROM driver Revision: 2.52
<4>sr1: scsi3-mmc drive: 6x/6x writer xa/form2 cdda tray
<6>(scsi0:0:0:0) Synchronous at 20.0 Mbyte/sec, offset 8.
<4>SCSI device sda: hdwr sector= 512 bytes. Sectors= 8388315 [4095 MB] [4.1 GB]
<6>(scsi0:0:1:0) Synchronous at 10.0 Mbyte/sec, offset 15.
<4>SCSI device sdb: hdwr sector= 512 bytes. Sectors= 8388315 [4095 MB] [4.1 GB]
<6>(scsi0:0:2:0) Synchronous at 20.0 Mbyte/sec, offset 8.
<4>SCSI device sdc: hdwr sector= 512 bytes. Sectors= 8386733 [4095 MB] [4.1 GB]


What else should be configured for the ZIP+ to work ?
Thanks so much.

-Dee


W.D.McKinney (Dee) [EMAIL PROTECTED]
Faith is acting on your passions & beliefs.

-
To get out of this list, please send email to [EMAIL PROTECTED] with
this text in its body: unsubscribe suse-linux-e
Check out the SuSE-FAQ at http://www.suse.com/Support/Doku/FAQ/ and the
archive at http://www.suse.com/Mailinglists/suse-linux-e/index.html

Reply via email to