I know the rule, try to research first on man pages,  openbsd.org, ect,
and ask people as a last resort. Unfortunately, I have exhausted
all resources online that I could find. (I was recommend to use this
email list by OpenBSd dev on reddit)

Currently, I am trying to use I2C on the latest version of aarch64 OpenBSD
on
RPI4. Are there any known drivers/libraries/userspace APIs to allow for
that? Or, I would have to write my own drivers for rpi4b?

I found these two papers on openbsd.org  touching these two particular
topics:

https://www.openbsd.org/papers/eurobsdcon2008-sensors.pdf

and

https://www.openbsd.org/papers/asiabsdcon2009-sensors-paper.pdf

However, my system lacks /sys/dev/i2c/i2c_scan.c or any other tool.

There are only headers files in the i2c directory:

/usr/include/dev/i2c/i2c_bitbang.h

/usr/include/dev/i2c/i2c_io.h

/usr/include/dev/i2c/i2cvar.h

/usr/include/dev/i2c/ihidev.h

So, I am stuck a bit... and have no idea what to do next...

Complete dmesg(8) below:

OpenBSD 7.0 (GENERIC.MP) #3: Wed Dec 15 13:14:20 MST 2021
    [email protected]:/usr/src/sys/arch/arm64/compile/
GENERIC.MP
real mem  = 8426483712 (8036MB)
avail mem = 8135118848 (7758MB)
random: good seed from bootblocks
mainbus0 at root: Raspberry Pi 4 Model B Rev 1.4
psci0 at mainbus0: PSCI 1.1, SMCCC 1.2
cpu0 at mainbus0 mpidr 0: ARM Cortex-A72 r0p3
cpu0: 48KB 64b/line 3-way L1 PIPT I-cache, 32KB 64b/line 2-way L1 D-cache
cpu0: 1024KB 64b/line 16-way L2 cache
cpu0: CRC32,ASID16
cpu1 at mainbus0 mpidr 1: ARM Cortex-A72 r0p3
cpu1: 48KB 64b/line 3-way L1 PIPT I-cache, 32KB 64b/line 2-way L1 D-cache
cpu1: 1024KB 64b/line 16-way L2 cache
cpu1: CRC32,ASID16
cpu2 at mainbus0 mpidr 2: ARM Cortex-A72 r0p3
cpu2: 48KB 64b/line 3-way L1 PIPT I-cache, 32KB 64b/line 2-way L1 D-cache
cpu2: 1024KB 64b/line 16-way L2 cache
cpu2: CRC32,ASID16
cpu3 at mainbus0 mpidr 3: ARM Cortex-A72 r0p3
cpu3: 48KB 64b/line 3-way L1 PIPT I-cache, 32KB 64b/line 2-way L1 D-cache
cpu3: 1024KB 64b/line 16-way L2 cache
cpu3: CRC32,ASID16
efi0 at mainbus0: UEFI 2.7
efi0: https://github.com/pftf/RPi4 rev 0x10000
smbios0 at efi0: SMBIOS 3.3.0
smbios0: vendor https://github.com/pftf/RPi4 version "UEFI Firmware v1.32"
date 10/19/2021
smbios0: Raspberry Pi Foundation Raspberry Pi 4 Model B
apm0 at mainbus0
"system" at mainbus0 not configured
"axi" at mainbus0 not configured
simplebus0 at mainbus0: "soc"
bcmclock0 at simplebus0
bcmmbox0 at simplebus0
bcmgpio0 at simplebus0
bcmaux0 at simplebus0
ampintc0 at simplebus0 nirq 256, ncpu 4 ipi: 0, 1: "interrupt-controller"
bcmtmon0 at simplebus0
bcmdmac0 at simplebus0: DMA0 DMA2 DMA4 DMA5 DMA6 DMA7 DMA8 DMA9
"timer" at simplebus0 not configured
pluart0 at simplebus0
com0 at simplebus0: ns16550, no working fifo
"local_intc" at simplebus0 not configured
bcmdog0 at simplebus0
bcmirng0 at simplebus0
"firmware" at simplebus0 not configured
"power" at simplebus0 not configured
"mailbox" at simplebus0 not configured
sdhc0 at simplebus0
sdhc0: SDHC 3.0, 250 MHz base clock
sdmmc0 at sdhc0: 4-bit, sd high-speed, mmc high-speed
"gpiomem" at simplebus0 not configured
"fb" at simplebus0 not configured
"clocks" at mainbus0 not configured
"phy" at mainbus0 not configured
"clk-27M" at mainbus0 not configured
"clk-108M" at mainbus0 not configured
simplebus1 at mainbus0: "emmc2bus"
sdhc1 at simplebus1
sdhc1: SDHC 3.0, 100 MHz base clock
sdmmc1 at sdhc1: 8-bit, sd high-speed, mmc high-speed, ddr52, dma
"arm-pmu" at mainbus0 not configured
agtimer0 at mainbus0: 54000 kHz
simplebus2 at mainbus0: "scb"
bcmpcie0 at simplebus2
pci0 at bcmpcie0
ppb0 at pci0 dev 0 function 0 "Broadcom BCM2711" rev 0x10
pci1 at ppb0 bus 1
xhci0 at pci1 dev 0 function 0 "VIA VL805 xHCI" rev 0x01: intx, xHCI 1.0
usb0 at xhci0: USB revision 3.0
uhub0 at usb0 configuration 1 interface 0 "VIA xHCI root hub" rev 3.00/1.00
addr 1
bse0 at simplebus2: address dc:a6:32:d3:42:c1
brgphy0 at bse0 phy 1: BCM54210E 10/100/1000baseT PHY, rev. 2
"dma" at simplebus2 not configured
"hevc-decoder" at simplebus2 not configured
"rpivid-local-intc" at simplebus2 not configured
"h264-decoder" at simplebus2 not configured
"vp9-decoder" at simplebus2 not configured
"leds" at mainbus0 not configured
"sd_io_1v8_reg" at mainbus0 not configured
"sd_vcc_reg" at mainbus0 not configured
"fixedregulator_3v3" at mainbus0 not configured
"fixedregulator_5v0" at mainbus0 not configured
simplebus3 at mainbus0: "v3dbus"
"bootloader" at mainbus0 not configured
simplefb0 at mainbus0: 800x600, 32bpp
wsdisplay0 at simplefb0 mux 1: console (std, vt100 emulation)
wsdisplay0: screen 1-5 added (std, vt100 emulation)
dt: 445 probes
scsibus0 at sdmmc1: 2 targets, initiator 0
sd0 at scsibus0 targ 1 lun 0: <SD/MMC, SR128, 0080> removable
sd0: 121942MB, 512 bytes/sector, 249737216 sectors
uhub1 at uhub0 port 1 configuration 1 interface 0 "VIA Labs USB2.0 Hub" rev
2.10/4.21 addr 2
bwfm0 at sdmmc0 function 1
manufacturer 0x02d0, product 0xa9a6 at sdmmc0 function 2 not configured
manufacturer 0x02d0, product 0xa9a6 at sdmmc0 function 3 not configured
uhidev0 at uhub1 port 4 configuration 1 interface 0 "SINO WEALTH USB
KEYBOARD" rev 1.10/1.00 addr 3
uhidev0: iclass 3/1
ukbd0 at uhidev0: 8 variable keys, 6 key codes
wskbd0 at ukbd0: console keyboard, using wsdisplay0
uhidev1 at uhub1 port 4 configuration 1 interface 1 "SINO WEALTH USB
KEYBOARD" rev 1.10/1.00 addr 3
uhidev1: iclass 3/0, 5 report ids
uhid0 at uhidev1 reportid 2: input=1, output=0, feature=0
ucc0 at uhidev1 reportid 3: 24 usages, 13 keys, enum
wskbd1 at ucc0 mux 1
wskbd1: connecting to wsdisplay0
uhid1 at uhidev1 reportid 5: input=0, output=0, feature=5
umass0 at uhub0 port 3 configuration 1 interface 0 "SupTronics X862" rev
3.00/0.20 addr 4
umass0: using SCSI over Bulk-Only
scsibus1 at umass0: 2 targets, initiator 0
sd1 at scsibus1 targ 1 lun 0: <ASMT, 2115, 0> serial.174c0862202101000034
sd1: 244198MB, 512 bytes/sector, 500118192 sectors
vscsi0 at root
scsibus2 at vscsi0: 256 targets
softraid0 at root
scsibus3 at softraid0: 256 targets
root on sd1a (e58930ea2c9b3c87.a) swap on sd1b dump on sd1b
WARNING: / was not properly unmounted
gpio0 at bcmgpio0: 58 pins
bwfm0:

P.S.
I am new here, so any input about writing style, and correct usage of
mailing lists are welcome!

Reply via email to