Hello, thank you for your reply!
I am trying to read data from an i2c sensor.


On Mon, Mar 21, 2022 at 2:53 AM David Gwynne <[email protected]> wrote:

> are you trying to add an i2c device to the sensor framework? or are you
> asking how to touch i2c devices from userland?
>
> > On 21 Mar 2022, at 16:21, Dr. T.I.S. <[email protected]> wrote:
> >
> > I know the rule, try to research first on man pages,  openbsd.org, ect,
> > and ask people as a last resort. Unfortunately, I have exhausted
> > all resources online that I could find. (I was recommend to use this
> > email list by OpenBSd dev on reddit)
> >
> > Currently, I am trying to use I2C on the latest version of aarch64
> OpenBSD
> > on
> > RPI4. Are there any known drivers/libraries/userspace APIs to allow for
> > that? Or, I would have to write my own drivers for rpi4b?
> >
> > I found these two papers on openbsd.org  touching these two particular
> > topics:
> >
> > https://www.openbsd.org/papers/eurobsdcon2008-sensors.pdf
> >
> > and
> >
> > https://www.openbsd.org/papers/asiabsdcon2009-sensors-paper.pdf
> >
> > However, my system lacks /sys/dev/i2c/i2c_scan.c or any other tool.
> >
> > There are only headers files in the i2c directory:
> >
> > /usr/include/dev/i2c/i2c_bitbang.h
> >
> > /usr/include/dev/i2c/i2c_io.h
> >
> > /usr/include/dev/i2c/i2cvar.h
> >
> > /usr/include/dev/i2c/ihidev.h
> >
> > So, I am stuck a bit... and have no idea what to do next...
> >
> > Complete dmesg(8) below:
> >
> > OpenBSD 7.0 (GENERIC.MP) #3: Wed Dec 15 13:14:20 MST 2021
> >    [email protected]:/usr/src/sys/arch/arm64/compile/
> > GENERIC.MP
> > real mem  = 8426483712 (8036MB)
> > avail mem = 8135118848 (7758MB)
> > random: good seed from bootblocks
> > mainbus0 at root: Raspberry Pi 4 Model B Rev 1.4
> > psci0 at mainbus0: PSCI 1.1, SMCCC 1.2
> > cpu0 at mainbus0 mpidr 0: ARM Cortex-A72 r0p3
> > cpu0: 48KB 64b/line 3-way L1 PIPT I-cache, 32KB 64b/line 2-way L1 D-cache
> > cpu0: 1024KB 64b/line 16-way L2 cache
> > cpu0: CRC32,ASID16
> > cpu1 at mainbus0 mpidr 1: ARM Cortex-A72 r0p3
> > cpu1: 48KB 64b/line 3-way L1 PIPT I-cache, 32KB 64b/line 2-way L1 D-cache
> > cpu1: 1024KB 64b/line 16-way L2 cache
> > cpu1: CRC32,ASID16
> > cpu2 at mainbus0 mpidr 2: ARM Cortex-A72 r0p3
> > cpu2: 48KB 64b/line 3-way L1 PIPT I-cache, 32KB 64b/line 2-way L1 D-cache
> > cpu2: 1024KB 64b/line 16-way L2 cache
> > cpu2: CRC32,ASID16
> > cpu3 at mainbus0 mpidr 3: ARM Cortex-A72 r0p3
> > cpu3: 48KB 64b/line 3-way L1 PIPT I-cache, 32KB 64b/line 2-way L1 D-cache
> > cpu3: 1024KB 64b/line 16-way L2 cache
> > cpu3: CRC32,ASID16
> > efi0 at mainbus0: UEFI 2.7
> > efi0: https://github.com/pftf/RPi4 rev 0x10000
> > smbios0 at efi0: SMBIOS 3.3.0
> > smbios0: vendor https://github.com/pftf/RPi4 version "UEFI Firmware
> v1.32"
> > date 10/19/2021
> > smbios0: Raspberry Pi Foundation Raspberry Pi 4 Model B
> > apm0 at mainbus0
> > "system" at mainbus0 not configured
> > "axi" at mainbus0 not configured
> > simplebus0 at mainbus0: "soc"
> > bcmclock0 at simplebus0
> > bcmmbox0 at simplebus0
> > bcmgpio0 at simplebus0
> > bcmaux0 at simplebus0
> > ampintc0 at simplebus0 nirq 256, ncpu 4 ipi: 0, 1: "interrupt-controller"
> > bcmtmon0 at simplebus0
> > bcmdmac0 at simplebus0: DMA0 DMA2 DMA4 DMA5 DMA6 DMA7 DMA8 DMA9
> > "timer" at simplebus0 not configured
> > pluart0 at simplebus0
> > com0 at simplebus0: ns16550, no working fifo
> > "local_intc" at simplebus0 not configured
> > bcmdog0 at simplebus0
> > bcmirng0 at simplebus0
> > "firmware" at simplebus0 not configured
> > "power" at simplebus0 not configured
> > "mailbox" at simplebus0 not configured
> > sdhc0 at simplebus0
> > sdhc0: SDHC 3.0, 250 MHz base clock
> > sdmmc0 at sdhc0: 4-bit, sd high-speed, mmc high-speed
> > "gpiomem" at simplebus0 not configured
> > "fb" at simplebus0 not configured
> > "clocks" at mainbus0 not configured
> > "phy" at mainbus0 not configured
> > "clk-27M" at mainbus0 not configured
> > "clk-108M" at mainbus0 not configured
> > simplebus1 at mainbus0: "emmc2bus"
> > sdhc1 at simplebus1
> > sdhc1: SDHC 3.0, 100 MHz base clock
> > sdmmc1 at sdhc1: 8-bit, sd high-speed, mmc high-speed, ddr52, dma
> > "arm-pmu" at mainbus0 not configured
> > agtimer0 at mainbus0: 54000 kHz
> > simplebus2 at mainbus0: "scb"
> > bcmpcie0 at simplebus2
> > pci0 at bcmpcie0
> > ppb0 at pci0 dev 0 function 0 "Broadcom BCM2711" rev 0x10
> > pci1 at ppb0 bus 1
> > xhci0 at pci1 dev 0 function 0 "VIA VL805 xHCI" rev 0x01: intx, xHCI 1.0
> > usb0 at xhci0: USB revision 3.0
> > uhub0 at usb0 configuration 1 interface 0 "VIA xHCI root hub" rev
> 3.00/1.00
> > addr 1
> > bse0 at simplebus2: address dc:a6:32:d3:42:c1
> > brgphy0 at bse0 phy 1: BCM54210E 10/100/1000baseT PHY, rev. 2
> > "dma" at simplebus2 not configured
> > "hevc-decoder" at simplebus2 not configured
> > "rpivid-local-intc" at simplebus2 not configured
> > "h264-decoder" at simplebus2 not configured
> > "vp9-decoder" at simplebus2 not configured
> > "leds" at mainbus0 not configured
> > "sd_io_1v8_reg" at mainbus0 not configured
> > "sd_vcc_reg" at mainbus0 not configured
> > "fixedregulator_3v3" at mainbus0 not configured
> > "fixedregulator_5v0" at mainbus0 not configured
> > simplebus3 at mainbus0: "v3dbus"
> > "bootloader" at mainbus0 not configured
> > simplefb0 at mainbus0: 800x600, 32bpp
> > wsdisplay0 at simplefb0 mux 1: console (std, vt100 emulation)
> > wsdisplay0: screen 1-5 added (std, vt100 emulation)
> > dt: 445 probes
> > scsibus0 at sdmmc1: 2 targets, initiator 0
> > sd0 at scsibus0 targ 1 lun 0: <SD/MMC, SR128, 0080> removable
> > sd0: 121942MB, 512 bytes/sector, 249737216 sectors
> > uhub1 at uhub0 port 1 configuration 1 interface 0 "VIA Labs USB2.0 Hub"
> rev
> > 2.10/4.21 addr 2
> > bwfm0 at sdmmc0 function 1
> > manufacturer 0x02d0, product 0xa9a6 at sdmmc0 function 2 not configured
> > manufacturer 0x02d0, product 0xa9a6 at sdmmc0 function 3 not configured
> > uhidev0 at uhub1 port 4 configuration 1 interface 0 "SINO WEALTH USB
> > KEYBOARD" rev 1.10/1.00 addr 3
> > uhidev0: iclass 3/1
> > ukbd0 at uhidev0: 8 variable keys, 6 key codes
> > wskbd0 at ukbd0: console keyboard, using wsdisplay0
> > uhidev1 at uhub1 port 4 configuration 1 interface 1 "SINO WEALTH USB
> > KEYBOARD" rev 1.10/1.00 addr 3
> > uhidev1: iclass 3/0, 5 report ids
> > uhid0 at uhidev1 reportid 2: input=1, output=0, feature=0
> > ucc0 at uhidev1 reportid 3: 24 usages, 13 keys, enum
> > wskbd1 at ucc0 mux 1
> > wskbd1: connecting to wsdisplay0
> > uhid1 at uhidev1 reportid 5: input=0, output=0, feature=5
> > umass0 at uhub0 port 3 configuration 1 interface 0 "SupTronics X862" rev
> > 3.00/0.20 addr 4
> > umass0: using SCSI over Bulk-Only
> > scsibus1 at umass0: 2 targets, initiator 0
> > sd1 at scsibus1 targ 1 lun 0: <ASMT, 2115, 0> serial.174c0862202101000034
> > sd1: 244198MB, 512 bytes/sector, 500118192 sectors
> > vscsi0 at root
> > scsibus2 at vscsi0: 256 targets
> > softraid0 at root
> > scsibus3 at softraid0: 256 targets
> > root on sd1a (e58930ea2c9b3c87.a) swap on sd1b dump on sd1b
> > WARNING: / was not properly unmounted
> > gpio0 at bcmgpio0: 58 pins
> > bwfm0:
> >
> > P.S.
> > I am new here, so any input about writing style, and correct usage of
> > mailing lists are welcome!
>
>

Reply via email to