Don't have time to scan the schematic, but here are the voltages you asked for:
R4160= +26V R4163= -26V And also R4161= -26V Also check the following chokes that are in series with the resistors: L4000, L4001, L4002. They open up also if the IC shorts. Chuck Perlingiero Chuck's Electronic Repair (610) 623-2224 (610) 259-9618 (Fax) [EMAIL PROTECTED] -----Original Message----- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] Behalf Of Joe Dickerson Sent: Tuesday, April 06, 2004 12:56 AM To: ELECTRONICS PROFESSIONALS LIST Subject: Re: [Techs] Zenith 9-1690...Mod. PVY5263RK('96)..convergence.wayout...... Jeff, I can't thank you enough for the responses, but I still think part of my problem is the Vcc going to the 9-1690 (convergence). I don't show any B+ on either side of these two resistors.....(R1460 and R4163).......and I am stuck for schematics, because not one tech has responded with any information as to the whereabouts of a print for this set. I guess it was a loser for Zenith. Anyways, I'll call all of my distributors tomorrow and some I've never tried b4 and do whatever it takes to win this battle. Thanks Again. Joe Intrepid Video Support wrote: > Joe, > You can get this board rebuilt from PTS for around $113..that price is 2 years old. > www.ptscorp.com > Most are repaired simply by replacing the IC's, the one ohm resistors and the 82/110k resistors on the > 9-1674 board. > If you are missing your supply voltages, you may have another open resistor. > I added the module number to the subject line with hopes it gets someone else's attention...but you need > to replace these parts, then see where you are. > > Jeff Dougherty > Intrepid Video TV/VCR > 263 S Front St > Steelton PA 17113 > fax...717-564-4952 > www.intrepid-video.com www.tech-repair.net > > ----- Original Message ----- > From: "Joe Dickerson" <[EMAIL PROTECTED]> > To: "ELECTRONICS PROFESSIONALS LIST" <[EMAIL PROTECTED]> > Sent: Monday, April 05, 2004 1:17 PM > Subject: Re: [Techs] Zenith Mod. PVY5263RK('96) ...convergence out......wayout...... > > > Since no-one has the schematics on this set, where would be the best > place to obtain them? I really need to get this set out'a here fast! > Thanks for ANY responses. > Joe > > Joe Dickerson wrote: > >>Nope... it's marked R1460 on the pc board. I'll try to check the other >>stuff you mentioned, though. Thanks for the response. >>Joe >> >>Intrepid Video Support wrote: >> >> >>>Joe, >>>Those resistors are probable 1 ohm...It appears you mistyped the one >>>as R1460, did you mean R4160? >>>Replace these and replace the two convergence amps. >>>Also check The 5a Pigtail Fuses On The Main Ps/Sweep Board May Be Open >>>And Open R3243* 110k Resistor On Power Supply. Also Check R3244*82k. >>>Also, resolder the connector on the 9-1674 module, there is a stand up >>>PCB with a cable going to the CRT >>>boards. I always remove the support bracket and solder these pins..the >>>replace the bracket. >>> >>>Jeff Dougherty >>>Intrepid Video TV/VCR >>>263 S Front St >>>Steelton PA 17113 >>>fax...717-564-4952 >>>www.intrepid-video.com www.tech-repair.net >>> >>>----- Original Message ----- From: "Joe Dickerson" <[EMAIL PROTECTED]> >>>To: "techs" <[EMAIL PROTECTED]> >>>Sent: Wednesday, March 31, 2004 9:43 PM >>>Subject: [Techs] Zenith Mod. PVY5263RK ('96) ...convergence >>>out......wayout...... >>> >>> >>>SMPS; 9-1674-01 >>>Convergence; 9-1690 >>>Main; 9-1679-01 >>> Convrgence out. Looks like 3 pictures superimposed on top of each >>>other. When I go through the menu to adjust, the adjustment controls >>>have no control. There are two resistors burned beyond recognition on >>>the 9-1690 convergence board. They are R4163 and R1460. Using the neg. >>>side of C4102 as ref. grd, I have 0 VDC on either side of these >>>resistors. I assume the supply voltages (I think there is a +24 and a >>>-24 vdc going to the convergencve amps (STK392-110). I'm not sure of >>>these voltages, though, since I have no schematics. (Hint, hint). The >>>two red horiz. lines are shifted to the left and won't budge over to the >>>right. The two vertical lines are shifted to the top and won't move down >>>at all. Can anyone out there give a guy a help up on this? >>>Any help is VERY much appreciated on this one. (any of them)! >>>Thanks ahead >>>Joe >> >> >> > > -- Joe Dickerson Joe's TV & Appliance Rt 1 Box 3781 Jasper, Texas 75951 (409) 384-3325 use same no. for fax _______________________________________________ Tech Repair CD...order your just $49.00 plus shipping...One year of updates free. www.intrepid-video.com www.tech-repair.net Techs mailing list [EMAIL PROTECTED] http://intrepid-video.com/mailman/listinfo/techs_intrepid-video.com _______________________________________________ Tech Repair CD...order your just $49.00 plus shipping...One year of updates free. www.intrepid-video.com www.tech-repair.net Techs mailing list [EMAIL PROTECTED] http://intrepid-video.com/mailman/listinfo/techs_intrepid-video.com
