Jeff can you tell me what position the little switch on the rear of the TECI1 adapter should be in? Or does it matter? If I have to change the SSB I will need to download the info from the old to the new board?
Robert J. Delhommer, Sr. Bob's Electronics & TV P.O. Box 40 / 212 W. Lafayette St. Maurice, LA 70555 USA ----- Original Message ----- From: "Intrepid Video Support" <[EMAIL PROTECTED]> To: "ELECTRONICS PROFESSIONALS LIST" <[EMAIL PROTECTED]> Sent: Monday, December 06, 2004 2:00 PM Subject: Re: [Techs] RCA D52W20BYX1 ITC222 Dead Robert. In all the times I called tech support, they never cared about the error codes. This should be on your Tech Repair CD: RCA\D52W19 ITC222\Troubleshooting\\\ITC222\Set should power up with the CRTs disconnected\Disconnect the H & V yokes*Disconnect BW001 & BW002*Disconnect BA010 (audio)*Disconnect BP611 to convergence PS\If the set powers up reconnect one at a time trying to turn on the set* and troubleshoot that circuit that caused the shutdown\If the set will not power up when these are disconnected the trouble is on the small signal board\\\\\ More than likely you have a defective small signal board. You can try reflowing the solder on the connectors for the ribbon connectors and spray contact cleaner inside the connectors. Also, be sure all connectors are in place, especially the ones to the CRT's..they like to pull out when you slide the PCB tray out. This may help, also.: RCA\D52W20 ITC222 ATC221\Shutdown troubleshooting\\\ITC222 ATC221\To temporarily defeat shutdown (FOR TEST ONLY) short transistor TV852 B-E on small signal board location H-7\\\\\\\\ Jeff -- Intrepid Video TV/VCR Repair 263 S Front St, Steelton PA 17113 717-939-7708; (F) 717-564-4952 www.intrepid-video.com www.tech-repair.net ----- Original Message ----- From: "Bob's TV" <[EMAIL PROTECTED]> To: <[EMAIL PROTECTED]> Sent: Monday, December 06, 2004 2:35 PM Subject: [Techs] RCA D52W20BYX1 ITC222 Dead This set came in dead, when plugged in and pressing the power button the set will cycle 3 times each time the green power LED flashes and you hear a chirp. Tried disconnecting HV Splitter. Checking error codes found Error Code 61 :HW:Switched 5Volt not available.SMPS cannot switch. Also Code:1:Invalid Error Code Code:1:Invalid Error Code. What is HW?? Anyone have any suggestions on this set or can answer the question What is HW?? & where do I look for the Switched 5Volt, is it on the SSB or Deflection board? Robert J. Delhommer, Sr. Bob's Electronics & TV P.O. Box 40 / 212 W. Lafayette St. Maurice, LA 70555 USA _______________________________________________ Tech Repair CD...order your just $49.00 plus shipping...One year of updates free. www.intrepid-video.com www.tech-repair.net Techs mailing list [EMAIL PROTECTED] http://intrepid-video.com/mailman/listinfo/techs_intrepid-video.com _______________________________________________ Tech Repair CD...order your just $49.00 plus shipping...One year of updates free. www.intrepid-video.com www.tech-repair.net Techs mailing list [EMAIL PROTECTED] http://intrepid-video.com/mailman/listinfo/techs_intrepid-video.com _______________________________________________ Tech Repair CD...order your just $49.00 plus shipping...One year of updates free. www.intrepid-video.com www.tech-repair.net Techs mailing list [EMAIL PROTECTED] http://intrepid-video.com/mailman/listinfo/techs_intrepid-video.com
