The adhoc network looks like any other wireless device. Do check the version. I think I had to start the chat on the 1.5, but I am not sure.
Gerald On Sunday, February 6, 2011, Caryl Bigenho <[email protected]> wrote: > > > > > > OK I think I know what happened. First a question... how will the ad hoc > networks look on the XO-1? They were still targets on these. Maybe I > grabbed the wrong usb stick and put 10.1.2 on them again... but I don't think > so. > > I didn't see any parenthesis... just that the 2 XO-1s could see each other > fine, but they couldn't see the 1.5s, even with sharing on. I started the > Chat on a 1.5. Maybe it has to start on a 1.0? > > Caryl > >> Date: Sun, 6 Feb 2011 12:52:01 -0500 >> Subject: Re: [Testing] [support-gang] Lost Communication in 10.1.3? >> From: [email protected] >> To: [email protected] >> CC: [email protected]; [email protected]; >> [email protected]; [email protected]; [email protected] >> >> Caryl, >> >> Once you connect to one of the ad-hoc networks, you will see the >> familiar parentheses surrounding it. Then, in the Neighborhood View on >> the the XOs, this network should appear as a wireless device. >> >> I would start troubleshooting by going o Settings and turning the >> radio off and then on again. >> >> Good luck. >> >> Gerald >> >> On Sunday, February 6, 2011, Caryl Bigenho <[email protected]> wrote: >> > >> > >> > >> > >> > >> > Hi Gerald, >> > >> > That was the first thing I tried and it didn't work for me. I'll try it >> > again when I get back from TX. How did you connect the 1.0 to the >> > network? They are still showing as access points rather than the Mayan >> > numerals on the 1.0s. Maybe I need to do the install again. >> > >> > Caryl >> > >> >> Date: Sun, 6 Feb 2011 11:39:38 -0500 >> >> From: [email protected] >> >> To: [email protected] >> >> CC: [email protected]; [email protected]; >> >> [email protected] >> >> Subject: Re: [Testing] [support-gang] Lost Communication in 10.1.3? >> >> >> >> Caryl, >> >> >> >> I have been able to make this work. Here's what I did: >> >> 1. Create an ad-hoc network on one of the 1.5s. >> >> 2. Connect to it on the 1.0s. >> >> 3. Open Chat and make public. >> >> >> >> Hope this helps. >> >> Gerald >> >> >> >> On Sunday, February 6, 2011, Caryl Bigenho <[email protected]> wrote: >> >> > >> >> >tee's what I >> >> > >> >> > >> >> >. >> >> >> >> H >> >> > Hi... >> >> > >> >> > Prepping some XOs for our booth at SCaLE 9X Feb 26-27. When I first >> >> > started charging and testing I was running 10.1.2. I tried Chat and >> >> > found that the XO-1s could easily chat with the XO-1.5s. >> >> > >> >> > Then I updated all of them to 10.1.3, and this ability seems to have >> >> > been lost. While the XO-1.5s connected right away to the ad hoc >> >> > network, the XO-1s were totally left out. They can only see each other. >> >> > >> >> > Is this an intentional change? Is there a way for both models to >> >> > communicate among themselves in 10.1.3? >> >> > >> >> > Caryl >> >> > >> >> _______________________________________________ >> >> Testing mailing list >> >> [email protected] >> >> http://lists.laptop.org/listinfo/testing >> > >> > > > _______________________________________________ Testing mailing list [email protected] http://lists.laptop.org/listinfo/testing
