So you should generate another/duplicate scraps with different names only with stations for part of map only with centerline and create map definition with them.
Martin Odesláno z iPhonu > 26. 11. 2024 v 17:02, Bill Gee <[email protected]>: > > Hi Pavel - > > It might - but then I have to keep two copies of the centerline data. Might > not be so bad now, but as more is added, I have to make sure both data sets > are in sync. > > =============== > Bill Gee > >> On 11/26/24 09:56, Pavel Herich wrote: >> This should help a bit: >> data normal from to tape compass clino ignoreall #ignore all lrud data in >> centerline >> 14P 15P 7.91 345 2.5 1.6 0.2 1.5 0.3 >> 15P 16P 5.4 25 -3 0 1.5 1.2 2 >> ... >> Pavel >> Dňa 2024-11-26 16:46 Bill Gee napísal(a): >>> Thank you all for your suggestions and hints. I have figured out how to >>> make this work - Mostly! >>> >>> Take a look at this map: >>> >>> https://campercaver.net/MiscFiles/CaveSpringCave-All.pdf >>> >>> This is very close to what I want. The only problem is more of an >>> annoyance. It appears that adding the centerline as a survey makes Therion >>> process the LRUDs to come up with a pseudo-wall. I would like that to go >>> away. I tried adding "hide-symbol line wall" to the layout, but that made >>> all of the walls go away. >>> >>> In the thconfig file I changed the "source" line to the new .th file, added >>> a symbol-hide line for cross-sections and changed the name of the output >>> file on the export line. I also changed the "select" line to reference >>> MainPlan-All. >>> >>> Here is how I set up the .th file: >>> >>> ======================== >>> map MainPlan-All >>> MainPlan >>> MainCenterLine >>> endmap >>> >>> # Create the main map to include all submaps >>> map MainPlan -title "CaveSpringCave (SHN-017) - Plan View" -projection plan >>> >>> # X and Y upper level >>> X-Survey@CaveSpringCave >>> Y-Survey@CaveSpringCave >>> >>> # Main passages >>> MainPassages@CaveSpringCave >>> >>> # Lower stream passage >>> A-Entrance@CaveSpringCave >>> A-Survey@CaveSpringCave >>> >>> # T-Survey - Small side passage off upper trunk >>> T-Survey@CaveSpringCave >>> endmap >>> >>> survey MainCenterLine >>> centreline >>> >>> # Define the units that will be used. >>> units compass degrees >>> units clino degrees >>> units length feet >>> units depth feet >>> units tape feet >>> units altitude feet >>> units dimensions feet >>> >>> # A separate file contains all of the survey data. Use multiple files as >>> needed >>> input CaveSpringCave-Surveydata.txt >>> >>> endcentreline >>> endsurvey >>> >>> survey CaveSpringCave -title "Cave Spring Cave" >>> >>> centreline >>> >>> # Define the units that will be used. >>> units compass degrees >>> units clino degrees >>> units length feet >>> units depth feet >>> units tape feet >>> units altitude feet >>> units dimensions feet >>> >>> # A separate file contains all of the survey data. Use multiple files as >>> needed >>> input CaveSpringCave-Surveydata.txt >>> >>> endcentreline >>> >>> >>> # Lower stream passage A survey >>> input 20161107/CaveSpringCave-LowerEntrance.th2 >>> input 20221013/CaveSpringCave-A3-A7.th2 >>> input 20221013/CaveSpringCave-A7-A17.th2 >>> [much more omitted ...] >>> >>> ============================== >>> >>> =============== >>> Bill Gee >>> >>> On 11/25/24 09:31, Bill Gee wrote: >>>> Actually, I would like full detail where it exists and centerline only >>>> where it does not. Martin's hints give me an idea how to get this. It >>>> will take a day or two for me to set it up and test. >>>> >>>> I also want maps where only the drawn stuff is shown. I think what I need >>>> to do is leave those parts of *.th2 and thconfig alone, and add new stuff >>>> as noted by Martin. >>>> >>>> One additional question regarding the "select" statement location ... I >>>> think I need to put it in thconfig just before the layout and export lines >>>> that creates the file, like this: >>>> >>>> ====================== thconfig ============ >>>> select MainPlan >>>> >>>> layout basics >>>> ... >>>> endlayout >>>> >>>> (more layout sections) >>>> >>>> export map -proj plan -layout ChosenLayout -o Outputfile >>>> >>>> (several more "export map" commands to get Loch, Aven, KML etc files) >>>> >>>> select FullMap >>>> >>>> layout FullMapLayout >>>> ... >>>> endlayout >>>> >>>> export map -proj plan -layout FullMapLayout -o AnotherOutputFile >>>> ====================== >>>> >>>> Is this about right? >>>> >>>> Another way I might do it is to create entirely new thconfig and *.th2 >>>> files just for this map, then use a "system" call in the main thconfig to >>>> launch another instance of therion with the alternate thconfig as a >>>> command line option. >>>> >>>> =============== >>>> Bill Gee >>>> >>>> On 11/25/24 08:38, Martin Sluka via Therion wrote: >>>>> It means you want only centerline for all the data set and walls for only >>>>> part of a cave. Correct? >>>>> >>>>> Define map which will contain only survey data. >>>>> Define other map, which will contain only sraps or maps from scraps for >>>>> that part of the cave you want. >>>>> Define map, which will include both maps defined above. >>>>> Select this map in thconfig >>>>> Add to layout: >>>>> symbol-hide group all >>>>> symbol-show line wall >>>>> symbol-show group centerline >>>>> (or symbol-show line centerline) >>>>> >>>>> It should work >>>>> >>>>> M. >>>>> >>>>> >>>>> Odesláno z iPhonu >>>>> >>>>>> 25. 11. 2024 v 14:03, Bill Gee <[email protected]>: >>>>>> >>>>>> I am looking at this entry in the Wiki: >>>>>> >>>>>> https://therion.speleo.sk/wiki/ >>>>>> tips#showing_centreline_for_parts_of_a_cave_and_passage_walls_for_others >>>>>> >>>>>> My understanding it that this requires making two sets of centerline >>>>>> data, then creating a survey for each set. One of the data sets is for >>>>>> that part of the cave which has walls/scraps and the other is for the >>>>>> remainder of the cave. >>>>>> >>>>>> The thconfig file is set up with only one survey/endsurvey section. I >>>>>> think this also would have to change into two sections. >>>>>> >>>>>> Is this correct? >>>>>> >>>>>> The cave I want to do this for has all centerline data in one big file. >>>>>> It would be a huge pain to separate that into two files. Even more of a >>>>>> pain would be moving the data as sketching is completed. >>>>>> >>>>>> Thanks! >>>>>> -- =============== >>>>>> Bill Gee >>>>>> >>>>>> _______________________________________________ >>>>>> Therion mailing list >>>>>> [email protected] >>>>>> https://mailman.speleo.sk/listinfo/therion >>>>> _______________________________________________ >>>>> Therion mailing list >>>>> [email protected] >>>>> https://mailman.speleo.sk/listinfo/therion >>>> >>>> _______________________________________________ >>>> Therion mailing list >>>> [email protected] >>>> https://mailman.speleo.sk/listinfo/therion >>> >>> _______________________________________________ >>> Therion mailing list >>> [email protected] >>> https://mailman.speleo.sk/listinfo/therion >> _______________________________________________ >> Therion mailing list >> [email protected] >> https://mailman.speleo.sk/listinfo/therion > > _______________________________________________ > Therion mailing list > [email protected] > https://mailman.speleo.sk/listinfo/therion _______________________________________________ Therion mailing list [email protected] https://mailman.speleo.sk/listinfo/therion
