Hi That is indeed an odd update rate. The short term stability of the FE-5680 is in the parts in 10^-13 range once you get past 100 seconds. I would think updates of a DDS lsb or more would mess up the stability.
Of course if it is temperature correction, it may still be in the noise. Bob On Jan 29, 2012, at 8:22 AM, Javier Herrero <[email protected]> wrote: > El 29/01/2012 13:57, Magnus Danielson escribió: >> Hi Javier, >> >> On 01/29/2012 12:45 PM, Javier Herrero wrote: >>> Hello, >>> >>> As it has been discussed in the past days, the architecture of the newer >>> FE-5680A that has been recently purchased by a lot of us does not led to >>> a trimming resolution through the serial port of 1.7854e-7Hz, but rather >>> leds to think that the trimming resolution is in fact 6.80789e-6Hz >>> (relative frequency resolution 6.807e-13). >>> >>> I've hang a logic analyzer to the DDS SPI bus, and an SPI message >>> appears inmediately after updating the offset through the serial port. >>> I've found that the DDS is programmed in two frequencies, separated >>> 1400Hz near exactly, for each serial port offset setting, and that one >>> bit increment in the serial port offset setting is translated to a >>> one-bit increment for both DDS frequencies. The DDS frequencies are >>> alternated at 416.6666666Hz rate through FSELECT pin, at an invariable >>> 50% duty cycle, presumably to perform synchronous detection in the same >>> way as explained in the FRS-C manual. >>> >>> For example, the following data has been gathered: >>> >>> Serial offset 00 00 00 00 >>> DDS A word: 44 02 62 F6 = 1141007094 = 5 313 228.32219 Hz >>> DDS B word: 43 FD CC 8E = 1140706446 = 5 311 828.32085 Hz >>> >>> Serial offset 00 00 00 01 >>> DDS A word: 44 02 62 F7 = 1141007095 = 5 313 228.32685 Hz >>> DDS B word: 43 FD CC 8F = 1140706447 = 5 311 828.32550 Hz >>> >>> Serial offset 00 00 00 02 >>> DDS A word: 44 02 62 F8 = 1141007096 = 5 313 228.33151 Hz >>> DDS B word: 43 FD CC A0 = 1140706448 = 5 311 828.33016 Hz >>> >>> I've seen that these values seems to vary slightly from time to time in >>> the less significative digits, I've been then change in the order of 2-3 >>> units from one data take to a different one minutes later. I've checked >>> that the unit updates each several seconds the DDS control words, and >>> I've seen changes in the lower significant bits at minutes intervals, >>> although most of the times, same previous words are sent. I suspect this >>> is some form of unit self-compensation, perhaps to temperature changes. >>> >>> Last, I've sent an offset of 1468879 units, that shoudl correspond to a >>> 10Hz frequency change assuming a trimming resolution of 6.90789e-6Hz, >>> and after a temporary unit unlock, it has locked exactly at 10 000 >>> 010.000 Hz. So I can conclude that these units are not fully compliant >>> with the manual we are handling, and that the trimming resolution is >>> 6.80789e-6Hz and not the stated 1.7854e-7Hz. >> >> Good work Javier! >> >> It also makes perfect sense from the hardware architecture of these newer >> 5680A. It's nothing wrong with it, it's just different. >> >> Somebody put this up on the wiki. >> >> I will receive new 5680A when I pickup the packet on Monday, I only have an >> older variant with serial port and DDS output. >> >> Cheers, >> Magnus >> > I've just gathered the following message from the unit using the serial tool: > > Cmd 0x22 0x0D byte reply: [22] [0D] [00] [2F] [44] [02] [62] [EF] [43] [FD] > [CC] [87] [3E] > Cmd 0x22 ASCII (.): D.b.C... > Cmd 0x22 ASCII ( ): D b C > > It seems that these are the current DDS values. Since now they are a slightly > different of what I've logged before, I suppose that they are updated and are > not some stored start-up values. So another reverse-engineered commad :) > > I'm currently logging with the logic analyzer the SPI activity to the DDS, it > seems to be updated at a somewhat outrangeous interval of 671.5 seconds or > something like that. It will take several hours to fill the analyzer memory :) > > Regards, > > Javier, EA1CRB > > > _______________________________________________ > time-nuts mailing list -- [email protected] > To unsubscribe, go to https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts > and follow the instructions there. _______________________________________________ time-nuts mailing list -- [email protected] To unsubscribe, go to https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts and follow the instructions there.
